J-Tech Digital ARC-HDEX40ARC Manual de usuario

ARC-HDEX40ARC

18G HDMI Extender with Audio Breakout

Version: ARC-HDEX40ARC1.3

User Manual

Statement

Thanks for choosing this product, please read this user manual carefully before using

this product. The functions described in this version are updated till May, 2019. In the

constant effort to improve our product, we reserve the right to make functions or

parameters changes without notice or obligation.

Safety Precaution

Do not dismantle the housing or modify the module to avoid electrical shock or burn.

Using supplies not meeting the products' specifications may cause damage,

deterioration or malfunction.

Do not expose the unit to rain, moisture or install this product near water.

Install the device in a place with fine ventilation.

Do not twist or pull by force ends of the optical cable. It can cause malfunction.

Do not use liquid or aerosol cleaners to clean this unit.

Always unplug the power to the device before cleaning.

Unplug the power when not used for a long period of time.

Refer all servicing to qualified service personnel.

After-sales Service

We provide limited warranty for the product within three years.

Packing List

1x Transmitter

2x TX Mounting Ears with 4 Screws

4x TX Plastic Cushions

1x 3-pin Terminal Block

1x Power Adapter (24V DC 1.25A)

1x Receiver

2x RX Mounting Ears with 4 Screws

4x RX Plastic Cushions

1x RS232 Cable (3-pin to DB9)

1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the

components is found.

Product Introduction

Thanks for choosing the ARC-HDEX40ARC HDMI 2.0 Extender, which consists of a

transmitter and a receiver. It can extend 4K video to distance up to 131 feet (40

meters) and 1080P video to distances up to 230 feet (70 meters) over a single CATx

cable. It supports audio de-embedded and ARC. It also supports bidirectional IR and

RS232 pass-through to control source or display device remotely. PoC feature allows

the transmitter and the receiver can be powered from each other and only one power

adapter is needed in system. Besides passing EDID information from the display, there

are multiple built-in EDID settings can be selected by the 4-pin DIP switch on the front

panel of transmitter. Moreover, the extender supports convenient firmware upgrade

through Micro-USB port.

Features

Supports HDMI 2.0 and the HDMI video resolution up to 4K@60Hz 4:4:4 HDR.

HDMI input supports HDCP 2.2 and the output support HDCP Active or HDCP

Passive mode.

Extends 4K signals to distances up to 131 feet (40 meters) and 1080P signals to

distances up to 230 feet (70 meters) over a single CATx cable.

Supports video resolution up-scaling, the 1080P input can be automatically

upgraded to 4K output.

SPDIF out on receiver for source audio de-embedding.

18Gbps high bandwidth.

Advanced EDID management: multiple built-in EDID settings can be selected.

Test pattern provides a built-in 4K/1080P image for troubleshooting.

Bidirectional IR, RS232 and 24V PoC.

Supports ARC.

Supports CEC pass-through.

Provides LEDs to indicate the current operating status.

Firmware upgrade by Micro-USB port.

Transmitter Panel Description

①Power LED: The LED illuminates red when power is applied.

②Test Pattern: Press the button with paper clip or other sharp tool to enable the

test pattern, and the left LED illuminates blue, the product generates an image of

1080P/60Hz color bar to output; Press this button again, the left LED blinks blue

at an interval of 500ms, the product generates an image of 4K/60Hz 4:4:4 color

bar to output. Press and hold this button for three seconds again can exit the Test

Pattern mode.

③1080P →4K: Press and hold the button at least three seconds with paper clip or

other sharp tool to enable 1080P to 4K up-scaling, and then the left LED

illuminates blue. Press and hold it again to exit.

④EDID: 4-pin DIP switch for EDID setting and HDCP mode selection. Please refer

to the EDID Management for more details.

⑤FW: Micro-USB port for firmware upgrade and user-defined EDID upload.

⑥HDMI In: Type-A female HDMI input port to connect a HDMI source.

⑦ARC Audio Out: Toslink connector to connect speaker or amplifier for ARC audio

output.

⑧IR In: 3.5mm jack to connect the IR receiver for IR pass-through.

⑨IR Out: 3.5mm jack to connect the IR emitter for IR pass-through.

⑩RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a

third-party device to be controlled.

⑪HDBT Out: RJ45 port to connect the HDBT input port of receiver by CATx

Ethernet cable. The LINK LED illuminates orange when there is a valid HDBaseT

link between the transmitter and the receiver. The HDCP LED illuminates green

when the video contains HDCP content.

⑫DC 24V: DC connector for the power adapter connection.

Tx Rx

LINKHDCP

123 4 5678910 11 12

HDBTOut

HDMI In

IROut

IRIn

ARC Aud io Out

Receiver Panel Description

①Power LED: The LED illuminates red when power is applied.

②ARC Mode: Press the button with paper clip or other sharp tool to enable the

ARC mode, and then the left LED illuminates blue. Press it again to exit the ARC

mode and the LED is off.

③ARC Audio In: Toslink connector to connect ARC audio source device (e.g.TV).

④FW: Micro-USB port for firmware upgrade.

⑤HDMI Out: Type-A female HDMI output port to connect HDMI display (e.g.TV).

⑥Audio Breakout: If the ARC mode is OFF, the Toslink connector is connected to

speaker or amplifier for HDMI source audio de-embedding. Note that if the ARC

mode is ON, this port has no audio output.

⑦IR In: 3.5mm jack to connect the IR receiver for IR pass-through.

⑧IR Out: 3.5mm jack to connect the IR emitter for IR pass-through.

⑨RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a

third-party device to be controlled.

⑩HDBT In: RJ45 port to connect the HDBT output port of transmitter by CATx

Ethernet cable. The LINK LED illuminates orange when there is a valid HDBaseT

link between the transmitter and the receiver. The HDCP LED illuminates green

when the video contains HDCP content.

⑪DC 24V: DC connector for the power adapter connection.

12345678911

DIP Switch Operation

EDID Management

The Extended Display Identification Data (EDID) is used by the source device to

match its video resolution with the connected display. By default, the source device

obtains its EDID from the first connected display. Meanwhile, since the displays with

different capabilities are connected to the extender, the DIP switch on the front panel

of transmitter can be used to set the EDID to a fixed value to ensure the compatibility

in video resolution.

The switch represents “0” when in the lower (OFF) position, and it represents “1” while

putting the switch in the upper (ON) position.

Switch 1~3 are used for EDID setting. The DIP switch status and its corresponding

setting are shown at the back of the product.

Switch Status

Video Resolution

Audio Format

000

Pass Through

001

1080P

2CH

010

3840x2160@30Hz

2CH

011

3840x2160@30Hz

Multi-CH

100

3840x2160@60Hz

2CH

101

3840x2160@60Hz

Multi-CH

110

3840x2160@60Hz HDR

Multi-CH (Supports PCM

2CH, PCM5.1, Dolby

1 2 3

EDID Setting

Default

1 2 3 4

OFF

0ON

OFF

HDCP Active

HDCP Passive

Pass Through

1080p 2CH

4K/30Hz Multi-CH

OFF

1 2 3

OFF

1 2 3

OFF

1 2 3

OFF

1 2 3

4K/30Hz 2CH

OFF

1 2 3

OFF

1 2 3

OFF

1 2 3

4K/60Hz 2CH

4K/60Hz Multi-CH

4K/60Hz HDR Multi-CH

OFF

1 2 3

User Defined

Digital 5.1,DTS 2CH)

111

User-defined EDID (Upload the EDID by Micro-USB port)

Note:

2CH: Supports LPCM 2CH.

Multi-CH: Supports LPCM 8CH, Dolby TrueHD, DTS-HD , Dolby Digital5.1, DTS

5.1, Dolby Digital Plus.

User-defined EDID Setting

Except directly invoking the built-in EDID, the specific EDID can be customized by

following the below operation process.

1) Rename the user-defined EDID according the following format.

EC_xx_xxxxx_xxxx_xxx.bin

EC: Fixed value

xx: EDID ID. It is “15”.

xxxxx: Video resolution.

xxxx: Refresh rate.

xxx: Audio format.

Example: EC_15_3840x2160_60Hz_ Dolby.bin

2) Connect the FW port of transmitter to the PC with USB cable, and then power on

the transmitter, the PC will automatically detect a virtual disk named of

“BOOTDISK”.

3) Double-click to open the disk, a file named of “READY.TXT” will be showed.

4) Copy the user-defined EDID (such as EC_15_3840x2160_60Hz_Dolby.bin) to

the “BOOTDISK” disk.

5) Reopen the disk to check the filename “READY.TXT” whether automatically

becomes “SUCCESS.TXT”, if yes, the user-defined EDID was imported into the

transmitter and saved as its corresponding EDID ID successfully.

6) Remove the USB cable, and then reboot the transmitter.

7) Now the new EDID can be invoked by setting the DIP switch status to “111”.

HDCP Mode

Put the switch 4 on the “ON” position to select HDCP Active mode, or on the “OFF”

position for HDCP Passive mode.

Switch Status

Mode

HDCP

OFF (0)

Passive

(Default)

Automatically follows the HDCP version of source

device.

ON (1)

Active

If the input video has HDCP content, the HDCP

version of HDMI output is HDCP 1.4 for broader

video solution.

If the input video has no HDCP content, the HDMI

output has no HDCP too.

ARC Mode

The front panel of receiver provides a buttons to enable or disable ARC mode, as

below figure shows:

Press the button with paper clip or other sharp tool to enable the ARC mode, and then

the left LED illuminates blue. Press it again to exit the ARC mode and the LED is off.

ARC Mode

Display (e.g.TV)

Audio Transmission Path

ARC is supported.

The TV audio is transmitted from the TV back

to the receiver via HDMI cable, and then it will

be output by the ARC Audio Out port of

transmitter.

ARC is not supported.

Connect the TV to the ARC Audio In port of

receiver with an audio cable. The TV audio is

transmitted from the TV back to the receiver via

the audio cable, and then it will be output by

the ARC Audio Out port of transmitter.

Note that if the ARC mode is ON, the Audio

Breakout port of receiver has no audio output.

OFF

The TV audio can’t be back to the ARC Audio

Out port of transmitter. The Audio Breakout

port of receiver is connected to speaker or

amplifier for HDMI source audio

de-embedding.

System Connection

The following diagram illustrates the typical input and output connections of the

extender:

1) The ARC mode of receiver is ON, and the display device (e.g. HDTV) supports

ARC. The TV audio is transmitted from the TV back to the receiver via HDMI

cable, and then it will be output by the ARC Audio Out port of transmitter.

Note: The STP cable is recommended to be used to ensure optimal machine

performance in ARC mode.

1 2 3 4

Tx Rx

LINKHDCP

Tx Rx

LINKHDCP

Speaker Laptop Remote HDTV

HDMI:

HDBaseT:

Audio:

IR:

RS232:

ARC

Tx Rx

Receiver

PoC

4K 40m 1080P 70m,

Emitter

2) The ARC mode of receiver is ON, but the display device (e.g. HDTV) doesn’t

support ARC. The TV audio is transmitted from the TV back to the receiver via the

audio cable, and then it will be output by the ARC Audio Out port of transmitter.

Note: The STP cable is recommended to be used to ensure optimal machine

performance in ARC mode.

1 2 3 4

Tx Rx

LINKHDCP

Tx Rx

LINKHDCP

Speaker Laptop Remote HDTV

HDMI:

HDBaseT:

Audio:

IR:

RS232:

ARC

Tx Rx

ARC

Receiver

PoC

4K 40m 1080P 70m,

Emitter

Tabla de contenidos

Otros manuales de Extensor de J-Tech Digital

J-Tech Digital

J-Tech Digital JTD-3023 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-EX230 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-2865 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-183 Manual de usuario

J-Tech Digital

J-Tech Digital ProAV Series Manual de usuario

J-Tech Digital

J-Tech Digital JTD-2980 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-3033 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-611V3 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-1651 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-2994 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-DVI-EX-196 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-2860 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-VW09 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-190 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-WEX-22 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-677 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-WEX20 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-185 Manual de usuario

J-Tech Digital

J-Tech Digital JTDHDEX-1 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-416 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-ex2 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-4K88-EX2 Manual de usuario

J-Tech Digital

J-Tech Digital JTECH-BE100 Manual de usuario

J-Tech Digital

J-Tech Digital JTD-2987 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario