Intersil ISL98001 Manual del propietario
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 1/16 Ver. 1.1, 12/19/05
Installation and Operation of Intersil’s ISL98001
Analog Front End Evaluation System
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 2/16 Ver. 1.1, 12/19/05
Note
To simplify installation and prevent unnecessary Windows messages during installation, do
not connect the USB cable to the ISL98001 Evaluation Board until the software installation is
complete.
PC Requirements
Operating System: Tested under Windows XP (service pack 2) and Windows 2000. Windows 98 and
ME not currently supported.
Hardware Requirements: USB Port, CD-ROM drive for install files, minimum 10MB free hard disk
space.
Software Installation
Launch the “ISL98001 Installer.exe” file on the CD ROM and follow the instructions. The default
installation will add an “Intersil” directory to the “Start Menu/Programs” tree. That directory will contain
a shortcut to the ISL98001 executable and an uninstaller. The main program files will be installed in
the Program Files/ISL98001 directory. The USB driver file windrvr6.sys will be placed into
C:\WINDOWS\system32\drivers and ISL98001.inf will be installed under C:\WINDOWS\INF.
Press “Next” to continue.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 3/16 Ver. 1.1, 12/19/05
By default, the installer will put the evaluation software under c:\Program Files\ISL98001 directory.
To us a different directory, select the “Browse” button.
Press “Next” to continue.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 4/16 Ver. 1.1, 12/19/05
Press “Next” to create the Intersil folder in the Start Menu.
Press the “Install” button to copy all the necessary files onto the PC.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 5/16 Ver. 1.1, 12/19/05
Connecting the Evaluation Board
After installation of the ISL98001 software, re-boot the PC if requested. Apply power to the ISL98001
Evaluation Board with the provided 5V power supply. Connect the USB cable to the ISL98001
Evaluation Board. The Microsoft windows operating system will see the ISL98001 Evaluation Board
as a new device, and will try to load appropriate driver for it.
Windows XP may pop up this message:
If you see this box, select “Yes, now and every time I connect a device” and click on “Next”. If you
elect not to select “Yes, now and every time I connect a device”, you may see this requester
whenever the device is reconnected after being disconnected.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 6/16 Ver. 1.1, 12/19/05
The following screen will then appear:
Press Next (“Install the software automatically”).
The Hardware Wizard will try to locate and install the driver for the ISL98001:
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 7/16 Ver. 1.1, 12/19/05
Click Finish to complete the installation.
On XP systems, a pop-up message may display the status of the ISL98001 hardware.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 8/16 Ver. 1.1, 12/19/05
Hardware Setup
By default, the ISL98001 Evaluation board is configured for an input video resolution of
1280x1024@60Hz on the VGA1 connector. The quickest way to verify operation is this:
•Connect a monitor with a DVI input to the DVI output connector
•Connect a 1280x1024@60Hz RGB video source to VGA1
•Connect the 5V power supply to the power connector
At this point, the evaluation board’s FPGA will format the data from the ISL98001 and generate SXGA
video timing on the DVI output connector. The incoming SXGA image should appear on the DVI
monitor.
Additional video modes and AFE configuration options are available using the ISL98001 evaluation
software through the USB interface.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 9/16 Ver. 1.1, 12/19/05
Starting the Software
Launch the software (default location is Start/Programs/Intersil/ISL98001).
After the program has launched, you should see the following screen:
Click on the “Read All Registers” button in the lower left screen. All of the register values from the
ISL98001 on the evaluation board should appear as shown in the next image. If the register values
are not read correctly, proceed to the Troubleshooting section of this document.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 10/16 Ver. 1.1, 12/19/05
To change a register value, simply change the hexadecimal number in the appropriate box. To
change both digits of the 8 bit hex number, select both digits with the mouse (or double click inside
the text box) , then quickly type both digits of the desired value. If you type too
slowly (more than 1 second between the first and second digit), the first digit typed will become the
lower nibble, and the higher nibble will be 0. To only change one nibble using the keyboard, select
the high nibble or the low nibble and type the new hexadecimal
value.
You can also change the register values using the keyboard:
•Increment by 1: Up Arrow
•Decrement by 1: Down Arrow
•Increment by 16 (increment high nibble by 1): Page Up
•Decrement by 16 (decrement high nibble by 1): Page Up
Tabla de contenidos
Otros manuales de Placa madre de Intersil
Intersil
Intersil ISL85003DEMO1Z Manual de usuario
Intersil
Intersil ISL3331EVAL1Z Manual de usuario
Intersil
Intersil JESD204B Manual de usuario
Intersil
Intersil HIP4086 Manual de usuario
Intersil
Intersil ISL75052SEHEVAL1Z Manual de usuario
Intersil
Intersil ISL54200EVAL1Z Manual de usuario
Intersil
Intersil ISL9440CEVAL1Z Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL71026MEVAL1Z Manual de usuario
Intersil
Intersil ISL6294AEVAL1Z Instrucciones de uso
Intersil
Intersil ISL6560 Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL8202MEVAL1Z Manual de usuario
Intersil
Intersil ISL59420/21EVAL1 Manual de usuario
Intersil
Intersil ZL2005P Manual de usuario
Intersil
Intersil ISL32741EVAL1Z Manual de usuario
Intersil
Intersil ISL9220IRTZEVAL1Z Instrucciones de instalación y funcionamiento
Intersil
Intersil ISL8011EVAL1Z Manual de usuario
Intersil
Intersil ISL78205EVAL1Z Manual
Intersil
Intersil ISL284xxEVAL1Z Series Manual de usuario
Intersil
Intersil ISL282x6EVAL1Z Manual de usuario
Intersil
Intersil ISL62381 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
