Interlogix UltraView IP XP4 Box Day/Night Range Camera Manual de usuario

UltraView IP XP4 Box

Day/Night Range Camera

User Manual

P/N 1234568A-EN • REV 1.0• ISS 19DEC12

2012 UTC Fire & Security Americas Corporation, Inc.

Interlogix is part of UTC Climate Controls & Security, a unit of United

Trademarks and

patents

The UltraView name and l

ogo are trademarks of United

Technologies.

Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands.

Certification

N4131

FCC compliance

Class A: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rul

es. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference a

t his own

expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

Canada

This Class

A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class A conforme à la norme NMB

-003

du Canada

European Union

directives

2004/108/EC (EMC directive):

Hereby, UTC Fire & Security

Americas Corporation, Inc.

declares that this device is in compliance

with the essential requireme

nts and other relevant provisions of

Directive 2004/108/EC

2002/96/EC (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local

supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info.

Contact information

For contact information see our Web site:

www.interlogix.com or

www.utcfssecurityproducts.eu

UltraView IP XP4 Box Day/Night Range Camera User Manual 1

Content

Introduction 2

Product description 2

Features 2

Installation 3

Installation environment 3

Package contents 3

Cable requirements 3

Setting up the camera 4

Camera description 5

Lenses 5

Mounting the camera 5

Connections 6

Alarm connection 6

Connecting analog cables 7

Setting the camera DIP switches 7

Description of the DIP switch settings 8

System configuration 9

Software requirements 9

Windows Vista and 7 users 9

Accessing the camera over the internet 10

Overview of monitoring and configuring the system 10

Live viewing 11

Monitoring the system 11

Configuring the camera and network 13

2 UltraView IP XP4 Box Day/Night Range Camera User Manual

Introduction

Product description

The UltraView IP XP4 box day/night range camera uses a digital signal

processor (DSP) to process video signals. The video camera includes a

microcontroller to provide high-quality images with high-color reproduction and

sharp pictures.

Product codes:

• UVC-IP-XP4DN-HR

• UVC-IP-XP4DN-HR-P

Features

Camera features include:

• H.264-SVC video compression with multistream capability

• Pixim Seawolf technology

• Excellent performance in almost any lighting conditions

• Supports up to 4CIF resolution (540HTVL analog)

• True day/night (removable IR cut filter)

• Long life and high reliability

• DIP switch control of camera settings

• Power over Ethernet (PoE) or Isolated switching power 12 VDC or 24 VAC

UltraView IP XP4 Box Day/Night Range Camera User Manual 3

Installation

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be done by qualified

service personnel. Always use a proper PoE switch or a 12 VDC or 24 VAC

UL listed Class 2 or CE certified power supply to power the camera. Do not

overload the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation of the

camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified temperature,

humidity or power source ratings. The operating temperature of the camera is

between -30 to +50°C (-22 to +122°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture, or try to operate it in

wet areas. Turn the power off immediately if the camera is wet and ask a

qualified service person for servicing. Moisture can damage the camera and

also create the danger of electric shock.

• Servicing: Do not attempt to service this camera yourself. Any attempt to

dismantle or remove the covers from this product will invalidate the warranty

and may also result in serious injury. Refer all servicing to qualified service

personnel.

WARNING: To reduce the risk of fire or electronic shock, do not expose the

camera to rain or moisture and do not remove the cover or back.

Package contents

The camera is shipped with the following items:

• The camera assembly

• 1 channel passive video transceiver

• AC power wiring harness

• 150 mm DC jack to terminal adapter

Cable requirements

For proper operation, adhere to the following cable and power requirements for

the cameras. Category 5 cabling or better is recommended. All network cabling

must be installed according to applicable codes and regulations.

4 UltraView IP XP4 Box Day/Night Range Camera User Manual

Table 1 below lists the requirements for the cables that connect to the camera.

Table 1: Recommended cable requirements

Cable type

Requirements

Video

75 ohm RS-59 coaxial cable with BNC ends

Power

24 VAC cable

Setting up the camera

Note: If the light source where the camera is installed experiences rapid, wide-

variations in lighting, the camera may not operate as intended.

To quickly put the camera into operation:

1. Connect the lens to the camera.

2. Prepare the mounting surface and mount the camera to the wall/ceiling using

the appropriate fasteners.

3. Connect the cables to the camera.

4. Connect a CCTV monitor to the system to program the camera.

5. Set the camera’s DIP switches, which are located on the rear of the camera,

to suit the camera’s location. See “Setting the camera DIP switches” on page

6. Set up the camera’s network and streaming parameters so that the camera

can be controlled over the network. See “Accessing the camera over the

internet” on page 10.

UltraView IP XP4 Box Day/Night Range Camera User Manual 5

Camera description

Figure 1: Side view of XP4 box camera

Auto iris lens connector

Video-type auto iris lens connection:

A. Video (white); B. Power; C. NC;

D. GND (black)

DC-type auto iris lens connection:

A. Driving coil (+);B. Damping coil (+);

C. Damping coil (-); D. Driving coil (-)

2. Camera

3. Back focus adjustment

4. Lens (auto

iris lens shown. Manual lens has

no cable.) Not included

5. Back focus lock screw

6. Auto iris lens cable. Not included

Lenses

Attach a manual lens using an auto electronic shutter (AES) lens or attach an

auto iris (AI) lens.

Mounting the camera

To mount the camera, attach the camera to the prepared mounting surface using

the appropriate mount.

6 UltraView IP XP4 Box Day/Night Range Camera User Manual

Connections

Figure 2: Rear panel of camera

Power LED.

Reset button.

Press to reset camera to factory default

settings.

Ethernet RJ45 port.

Connect to network devices.

DIP switches.

Configure camera settings.

5. Alarm input and output.

Connect to be able to trigger an alarm at

the network device.

6. Power supply.

Connect 12 VDC or 24 VDC power supply.

7. Video output.

Connect to a CCTV monitor

Alarm connection

Figure 3: DC alarm input and output wiring

1. OUT 2. GND 3. IN 4. GND

Table 2: Description of alarm connections

Alarm input

Type

TTL. Compliant with 48 V input voltage.

Connector type

Screw terminal

Alarm output

Type

Open collector. Compliant with 48 V external power.

Connector type

Screw terminal

UltraView IP XP4 Box Day/Night Range Camera User Manual 7

Connecting analog cables

Connect a standard CCTV monitor to the system to adjust the quality of the video

image using the DIP switches. The DIP switches can also be adjusted when

connected to the IP system.

To connect the cables:

1. Connect a coaxial cable from the camera’s BNC connector to a CCTV

monitor or video recording device.

2. Connect a PoE switch, a 12 VDC or 24 VAC power supply to the power input.

Do not connect both the PoE connection and DC or AC connection at the

same time.

Setting the camera DIP switches

You can set up six camera functions using the DIP switch bank on the rear of the

camera. Figure 4 below shows the DIP switch layout. See “Description of the DIP

switch settings” on page 8 for information on these functions.

Figure 4: DIP switch layout (located on rear of camera)

OFF

Table 3: DIP switch functions

Switch

Description

White balance

ON: ATW mode; OFF: PTL mode

Backlight compensation

ON: BLC on; OFF: BLC off

AI/AE exposure

ON: Auto exposure (AE) mode; OFF: Auto iris (AI) mode

Day/Night setting

ON: Black and white mode; OFF: Auto Day/Night mode

High/Normal Resolution

ON: High resolution; OFF: Normal resolution

Flickerless control

ON: Flickerless enabled; OFF: Normal

8 UltraView IP XP4 Box Day/Night Range Camera User Manual

Description of the DIP switch settings

White balance (WB)

White balance tells the camera what the color white looks like. Based on this

information, the camera will then display all colors correctly.

There are two methods to determine the WB:

• ATW (auto tracking white balance). The value used depends on the lighting

condition selected. It ensures reliable color reproduction when lighting

conditions change frequently.

• PTL (push-to-lock) white balance. WB is fixed at the moment the DIP switch it

set to ON.

Backlight compensation (BLC)

The backlight compensation function improves image quality when the

background illumination is high. It prevents the object in the center from

appearing too dark.

AI/AE exposure

Use this setting to select the method the camera uses to adjust to different light

levels.

Day/Night

This function controls if the camera switches to day/night mode. The camera

produces high-quality color video during the day or when light levels are high. It

then switches monochrome and removes the infrared filter to improve IR

sensitivity at night or when light levels are low.

Resolution

High resolution produces higher quality images but also increases the file size of

video images.

Flickerless control

Flickerless control eliminates the flicker caused by the differences between the

frequencies (60 Hz) of the ionization of the gas in a fluorescent light bulb with

that of the vertical frequency (59.95 Hz) in the camera. Although the difference is

very small, it results in a slight flicker at the top of the monitor scene or, in video

over IP applications, it would be interpreted as motion. Flickerless control helps

reduce the file size and transfer bit rates of compressed video images.

Reset button

Use this button to reset the camera to factory defaults including camera and

network settings. With the camera powered on press the red reset button for 10

to 15 seconds. The red LED indicator light flashes when the reset signal is

accepted.

Tabla de contenidos

Otros manuales de Cámara IP de Interlogix

Interlogix

Interlogix TVD-2202 Manual de usuario

Interlogix

Interlogix TruVisioin 12 Series Manual de usuario

Interlogix

Interlogix TruVision 12 Series Manual de usuario

Interlogix

Interlogix TVD-TIR6-MR Manual de usuario

Interlogix

Interlogix TVB-1101 Manual de usuario

Interlogix

Interlogix TruVision TVA-1101 Hoja de instrucciones

Interlogix

Interlogix UltraSync RS3130 Manual de usuario

Interlogix

Interlogix TVC-5125BE-3 Manual de usuario

Interlogix

Interlogix TruVision TVC-1201 Hoja de instrucciones

Interlogix

Interlogix TruVision TVB-4409 Manual