Intel 5000 Series Manual de usuario

Intel®5000 Sequence Processor

Integration

Warning, Important Safety Instructions

System power on/off: The power button DOES NOT turn off the system AC power. To remove power

from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is

unplugged before you open the chassis, add, or remove any components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,

telephone, and communication cables. Turn off the server workstation and disconnect the power cord,

telecommunications systems, networks, and modems attached to the server workstation before opening

it. Otherwise, personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other

parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one

is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis

ground any unpainted metal surface on your server workstation when handling parts.

ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD.

Hold boards only by their edges. After removing a board from its protective wrapper or from the server

workstation , place the board component side up on a grounded, static free surface. Use a conductive

foam pad if available but not the board wrapper. Do not slide board over any surface.

Installing the Processor

Note:

• Do not touch the contacts on either the processor or the processor socket.

• Do not force the processor socket into place. When correctly aligned, the socket will easily drop

into place.

To install a processor, follow these instructions:

1. Observe safety and ESD precautions.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the chassis cover. See the documentation that came with your chassis for instructions

on removing the cover.

5. Locate the processor sockets (see Figure 1).

Figure 1. Example: Locating Processor Sockets.

Note: Consult Your Board Documentation for Proper Socket Location

6. Disconnect and remove any components necessary to access the processor sockets. See the

documentation that came with your chassis for instructions on removing chassis components.

7. Push down on the lever attached to the processor socket. While holding the lever down, pull it

towards the center of the board to disengage the lever from the hook. Fully open the lever. See

Figure 2.

Figure 2. Opening Processor Socket Lever

8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully

open the load plate. See Figure 3.

Figure 3. Opening Load Plate

9. If the protective cover is attached from the load plate, remove it and store it for future use. See

Figure 4.

Figure 4. Removing Protective Cover from Load Plate

10. Remove the processor from the box and remove the protective shipping cover.

11. Set the processor in the socket with the processor cutouts matching the processor socket

notches. See Figure 5.

Figure 5. Setting Processor in Place

12. Close the load plate.

13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of

the processor socket to engage it under the hook on the processor socket.

Installing the Heat Sink(s)

Note: The heat sink has thermal interface material (TIM) located on the bottom of it. Use

caution when handling the heat sink so you do not damage the TIM.

Each processor requires a heat sink. Depending on your chassis, you may need to use

either a active (Figure 6) or an passive heat sink (Figure 7). An active heat sink has a fan

attached to the top of it and a cable that needs to be connected to the server board.

AF000099

Figure 6. Active Heat Sink (Cable Not Shown)

Use the following steps to install a heat sink.

1. Set the heat sink over the processor, lining up the four captive screws with the four posts

surrounding the processor.

2. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 7.

Do not fully tighten one screw before loosely attaching the others.

3. In the same order, gradually and equally tighten each captive screw until each is firmly

tightened. Do not fully tighten one screw at a time.

Figure 7. Installing Heat Sink (Passive Heat Sink Shown)

4. Active heat sink only: Connect the heat sink cable to the server board. Reference you board

documentation for proper fan header location.

5. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.

See the documentation that came with your chassis for instructions on installing chassis

components.

6. Replace the chassis cover and reconnect the AC power cord. See the documentation that came

with your chassis for instructions on installing the cover.

Otros manuales para 5000 Series

Tabla de contenidos

Otros manuales de Hardware de computadora de Intel

Intel

Intel Core i7-3960X Instrucciones de funcionamiento y seguridad

Intel

Intel SASWT4I Manual de instalación

Intel

Intel Xeon 5600 Series Manual técnico

Intel

Intel I/O Processor Manual de usuario

Intel

Intel 925 - Pentium D 925 3.0GHz 800MHz 4MB-Cache Socket 775... Manual de usuario

Intel

Intel Water 3.0 Performer C Manual de usuario

Intel

Intel BX80571E7500 - Core 2 Duo 2.93 GHz Processor Instrucciones de funcionamiento

Intel

Intel EP80579 Manual de usuario

Intel

Intel PXA27 Series Manual de usuario

Intel

Intel EP80579 Manual de usuario

Intel

Intel 865G Manual de usuario

Intel

Intel G34920-002 Manual de usuario

Intel

Intel BX80613I7980 Manual de usuario

Intel

Intel NUC Kit NUC11PAHi7 Manual de usuario

Intel

Intel FCPGA2 - Processor - 1 x Pentium 4 2.66 GHz Manual de instrucciones

Intel

Intel E2180 - Pentium Dual-Core 2.00GHz 800MHz 1MB Socket 775... Manual de instrucciones

Intel

Intel RMS2MH080 Manual de instalación

Intel

Intel RS3GC008 Manual de usuario

Intel

Intel SRCSASBB8I - RAID Controller Manual de instalación

Intel

Intel U3-1L Manual de usuario

Intel

Intel SBC 711 Guía rápida de usuario

Intel

Intel LGA1155 SOCKET - THERMAL MECHANICAL S AND DESIGN GUIDELINES... Manual de usuario

Intel

Intel 80C188EC Manual de usuario

Intel

Intel I5 3570K Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario

Jupiter

Jupiter RAM PACK Manual de usuario