IMT 4 Series Manual de usuario

IOWA MOLD TOOLING CO., INC.

P.O. Box 189

Garner, IA 50438

Tel: 641.923.3711

Fax: 641.923.2424

www.imt.com

Revised 05-24-2022

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any

means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa

Mold Tooling Co., Inc.

Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company

Series 4

Chassis Wiring

Manual # 91728483

Series 4 - Manual # 91728483

Operating, servicing and maintaining this vehicle

or equipment can expose you to chemicals

including engine exhaust, carbon monoxide,

phthalates, and lead, which are known to the

State of California to cause cancer and birth

defects or other reproductive harm. To minimize

exposure, avoid breathing exhaust, do not idle the

engine except as necessary, service your vehicle

or equipment in a well-ventilated area and wear

gloves or wash your hands frequently when

servicing. For more information go to

www.P65Warnings.ca.gov.

70490167

iii

Series 4 - Manual # 91728483

Table of Contents

S4 Ford 1

99906779 - Ford - Super Duty - Chassis Wiring ...........................................................................................2

99906779 - Ford - Super Duty - (IPU) w Optional Heater - Chassis Wiring................................................... 3

S4 RAM 5

99906780 - RAM - Chassis Wiring.................................................................................................................6

99906780 - RAM (IPU) w Optional Heater - Chassis Wiring .........................................................................7

GM/IH 9

99906781 - GM/IH - Chassis Wiring ............................................................................................................10

Peterbuilt 11

99906782 - Peterbuilt - IMT Installed Switches - Chassis Wiring ................................................................12

Kenworth 13

99906783 - Kenworth- IMT Installed Switches - Chassis Wiring .................................................................14

Series 4 - Manual # 91728483

S4 Ford 1 Section - 1

Series 4 - Manual # 91728483

S4 FordSection - 1

S4 Ford 2 Section - 1

Series 4 - Manual # 91728483

99906779 - Ford - Super Duty - Chassis Wiring

PTO GROUND

E-BRAKE

IGNITION

PTO RELAY BU/WT

SWITCH #6 POWER GY/OG

RUN/START OUT BN

UP-FITTER RELAY BOX

(UNDER HOOD)

PTO SELONOID GN/WH

PTO SOL.

CP-2100

SWITCH #5 POWER BRN/BLU

IN CAB SWITCH #1

IN CAB SWITCH #2

ENGINE SPEED 1

PTO RPM GN SEIC

PTO REF WH/BN SEIC

(*)

SIG RTN SEIC

(*)

SPEED CONTROL

77441694

BLACK

GREEN

RED

GAS DIESEL

PTO REF

SIG RTN

18 10

16 6

PTO RELAY BU/WH SEIC

PTO REQ 1 YE/GN SEIC

PARK BRAKE WH/VT SEIC

SEIC CONNECTOR

C213

(*) SEE ABOVE CHART

COMP POWER

BATTERY TO BATTERY

TO BATTERY

77441668

HORN

ENGINE START

PIN 4 YE/RD IGN SWITCH

TO HORN

TO BATTERY

PIN 4 YE/RD IGN SWITCH

PIN 7 BL/WT IGN SWITCH

TO BATTERY

ENGINE STOP

S4 Ford 3 Section - 1

Series 4 - Manual # 91728483

99906779 - Ford - Super Duty - (IPU) w Optional Heater - Chassis

Wiring

E-BRAKE

IGNITION

SWITCH #6 POWER GY/OG

RUN/START OUT BN

(UP-FITTER RELAY BOX)

CP-2100

SWITCH #5 POWER BRN/BLU

IN CAB SWITCH #1

IN CAB SWITCH #2

PARK BRAKE WH/VT

BATTERY TO BATTERY

77441668

HORN

HORN TO HORN

TO BATTERY

(SEIC)

(BODY POWER)

(MULTI)

COMP PWR TO BATTERY

TO HEATER

TO BATTERY

AUX #2 (IMT CNTRL PANNEL)

PTO GROUND

This page left intentionally blank

Series 4 - Manual # 91728483

S4 RAM 5 Section - 2

Series 4 - Manual # 91728483

S4 RAMSection - 2

S4 RAM 6 Section - 2

Series 4 - Manual # 91728483

99906780 - RAM - Chassis Wiring

NOTES:

1. PTO IS INTERLOCKED WITH THE PARKING BRAKE. IF THE PARKING BRAKE IS DISENGAGED, THE PTO WILL

DISENGAGE.

2. DIESEL ENGINE COOLANT MUST BE AT LEAST 20 DEGREES F BEFORE SPEED CONTROL WILL WORK.

3. GAS ENGINE COOLANT MUST BE AT LEAST 40 DEGREES F BEFORE SPEED CONTROL WILL WORK.

4. TRANSMISSION OIL MUST BE LEAST 20 DEGREES F BEFORE SPEED CONTROL WILL WORK.

77441668

PTO GROUND

E BRAKE

CP-2100

IN CAB SWITCH #1

IN CAB SWITCH #2

ENGINE SPEED 1

RAM ENGINE ON

PTO PRESSURE SW

AUX 3

AUX 4

W541 GREEN VISM GY/OG PIN 5

GY/YL

BATTERY

COMP POWER

IGNITION

PIN 6 FACTORY IGN PLUG

TO BATTERY

HORN

W522 GREEN VISM

TO BATTERY

PIN 1 FACTORY IGN PLUG

TO BATTERY

TO PTO SOLENOID

W725 BROWN VISM DG/WT PIN 11

DB/BG PIN 14

ENGINE START(STOP)

T754 DG/GR

BLACK PIN 6 FACTORY SPEED HARNESS

PINK PIN 3 FACTORY SPEED HARNESS

(UNDER FUSE BLOCK)

Tabla de contenidos

Manuales populares de Equipos de construcción de otras marcas

SASFORKS

SASFORKS EXTREME Manual de usuario

Hailo

Hailo H-50 Manual de usuario

Graco

Graco LineLazer ES 1000 Manual de uso y cuidado

Greenlee

Greenlee 555RSC Manual de usuario

Manitowoc

Manitowoc Grove CD3340B Manual de usuario

Lux Tools

Lux Tools A-FMR-20 Set Manual de usuario

SIP

SIP 03683 Manual de usuario

Volvo

Volvo L30G Manual de usuario

Grizzly

Grizzly G8712 Manual de usuario

Modulift

Modulift CMOD 12 Manual de usuario

Case

Case DV201 Manual de usuario

Sealey

Sealey SC10.V2 Manual de usuario

Wacker Neuson

Wacker Neuson DT05 Manual de usuario

HYVA

HYVA AMCO VEBA 81 Series Manual de usuario

Atlas Copco

Atlas Copco Dynapac V5100TV Manual de usuario

Toro

Toro 323 Manual de usuario

Manitowoc

Manitowoc National Crane 1400A Manual de usuario

SGS

SGS EC1500 Manual de usuario