Impex MARCY MD-859P Manual de usuario

MARCY DIAMOND

WEIGHT BENCH

MD-859P

IMPEX®INC.

2801 S. Towne Ave, Pomona, CA 91766

Tel: (800) 999-8899 Fax (626) 961-9966

www.impex-fitness.com

[email protected]

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Exploded Diagram

Parts List

Warranty

Ordering Parts

Model

MD-859P

Retain This

Manual for

Reference

110719

OWNER'S

MANUAL

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICE....................................................................... 2

HARDWARE PACK………............................................................................... 4

ASSEMBLY INSTRUCTIONS........................................................................... 5

EXPLODED DIAGRAM.................................................................................... 10

PARTS LIST..................................................................................................... 11

WARRANTY..................................................................................................... 12

ORDERING PARTS.......................................................................................... 12

BEFORE YOU BEGIN

Thank you for selecting the MARCY DIAMOND WEIGHT BENCH MD-859P by

IMPEX®INC. For your safety and benefit, read this manual carefully before

using the machine. As a manufacturer, we are committed to provide you

complete customer satisfaction. If you have any questions, or find there are

missing or damaged parts, we guarantee your complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please

call our TOLL-FREE customer service number. Our Customer Service

Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[email protected]

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave children

unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,

STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or

outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other

clothing that could become caught in the machine. Running or aerobic shoes are also

required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in

attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

13. Maximum user’s weight: 300 lbs.

14. Maximum weight on uprights: 600 lbs.

15. Maximum weight on leg developer: 100 lbs.

CARE AND MAINTENANCE

1. Inspect and tighten all parts before using the machine.

2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.

DO NOT use solvents.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT

YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS

OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH

PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS

EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL

INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF

THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

WARNING LABEL REPLACEMENT

The Warning Labels shown here have been placed on the Rear Base Frame and Rear

Stabilizer. If the labels are missing or illegible, please call customer service at

1-800-999-8899 for replacement. Apply the labels in location shown

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

ASSEMBLY INSTRUCTION

Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen

Wrenches. NOTE: It is strongly recommended for two or more people to assemble this

machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach one Base Frame (#3) to the Rear Base Frame (#2). Attach an Upright Beam (#1)

onto the Base Frame and Rear Base Frame. Secure them together with two M10 x 3 1/2”

Carriage Bolts (#32), one 5 ½” x 2” Bracket (#15), two Ø ¾” Washer (#41), and two M10

Aircraft Nuts (#44) from bottom. Secure with two M10 x 2 ¾” Carriage Bolts (#33), two Ø

¾” Washer (#41), and two M10 Aircraft Nuts (#44) from side. Do not tighten the Nuts

and Bolts yet. Repeat the same procedure to install the other side.

B.) Securely tighten all Nuts and Bolts.

C.)Insert two Crutches (#4) into the two Upright Beams. Insert two M18 Lock Knobs (#19)

through the selected holes to obtain desired height. DIAGRAM 1

STEP 2 (See Diagram 2)

A.) Attach the Main Seat Support (#5) to the Rear Stabilizer (#6). Secure it with two M10 x 2 ¾”

Carriage Bolts (#33), one 5 1/8” x 2 ¾” Bracket (#14), two Ø ¾” Washers (#41), and two M10

Aircraft Nuts (#44).

B.) Attach the two Incline Support Frames (#12) to the Main Seat Support. Secure them to the

Main Seat Support with three M10 x 3 1/2” Allen Bolts (#35), six Ø ¾” Washers (#41), and

three M10 Aircraft Nuts (#44). DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Attach the pivot on the Leg Developer Holder (#7) to the open bracket on the Main Seat

Support (#5). Attach the bottom of Leg Developer Holder to the Main Seat Support. Secure

it with one M10 x 2 ¾” Carriage Bolt (#33) from front, one M10 x 2 ½” Allen Bolt (#37) from

rear, two Ø ¾” Washers (#41), and one M10 Aircraft Nut (#44).

B.) Attach the Incline Support (#9) to the side-holes on the two Backrest Supports (#8). Align the

holes. Secure it with one M10 x 5 ½” Allen Bolt (#34), two Ø ¾” Washers (#41), and one M10

Aircraft Nut (#44).

C.) Attach the holes on the end of the Backrest Supports (#12) to the bracket on the Main Seat

Support. Align the holes. Secure the two Backrest Supports to the bracket, and the pivot on

Leg Developer Holder together with one M12 x 5 ¾” Hex Bolt (#31), two Ø 1” Washers (#41),

and one M12 Aircraft Nut (#44).

D.) Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports and Backrest

Incline are able to swivel.

E.) Place the other ends of Incline Support onto the selected slot on Incline Support Frames

(#12) to hold the Backrest Incline in position. DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Backrest Board (#17) to the Backrest Supports (#8). Secure it with four M8 x 1

5/8” Allen Bolts (#38) and four Ø 5/8” Washers (#42).

B.) Place the Seat Pad (#16) onto the seat bracket on Leg Developer Holder (#7). Secure it with

two M8 x 1 5/8” Allen Bolts (#38) and two Ø 5/8” Washers (#42). DIAGRAM 4

STEP 5 (See Diagram 5)

A.) Attach two Ø 3/4” Bushings (#20) to the Leg Developer (#10). Attach the Leg Developer to

the Leg Developer Holder (#7). Secure it with one M10 x 3 1/8” Allen Bolt (#36), two Ø ¾”

Washers (#41), and one M10 Aircraft Nut (#44).

B.) Insert three Foam Tubes (#13) halfway through the holes on the Leg Developer and Leg

Developer Holder. Push six Foam Rolls (#27) onto the Tubes from both ends. Plug six Foam

Roll End Caps (#26) into the ends.

C.) Slide an Olympic Sleeve (#29) onto the weight post on Leg Developer. Attach a Spring Clip

(#30) onto the Sleeve.

D.) Attach the Arm Curl Pad (#18) to the Arm CurlStand (#11). Secure it with two M8 x 5/8” Allen

Bolts (#39) and two Ø 5/8” Washers (#42).

E.) Insert the Arm Curl Stand into the Leg Developer holder. Use the M10 Lock Knob (#28) to

lock the Arm Curl Stand in position.

F.) Remove the Arm Curl Stand when doing Leg Developer exercises. DIAGRAM 5

Tabla de contenidos

Otros manuales de Gimnasio en casa de Impex

Impex

Impex Marcy Platinum MP-2105 Manual de usuario

Impex

Impex IRON GRIP STRENGTH TSA-5762 Manual de usuario

Impex

Impex MARCY DIAMOND ELITE MD-389 Manual de usuario

Impex

Impex POWERHOUSE SB-210 Manual de usuario

Impex

Impex MARCY MWB 850 Manual de usuario

Impex

Impex STT 353 Manual de usuario

Impex

Impex Powerhouse Club PHC 710 Manual de usuario

Impex

Impex CB-202 Manual de usuario

Impex

Impex IGS-6500 Manual de usuario

Impex

Impex MARCY MKB-957 Manual de usuario

Impex

Impex COMPETITOR WM-357 Manual de usuario

Impex

Impex MARCY PRO 5 Manual de usuario

Impex

Impex PLATINUM MARCY PM-3000 Manual de usuario

Impex

Impex MARCY MWB-4300 Manual de usuario

Impex

Impex Circuit Fitness AMZ-986RW Instrucciones de instalación y funcionamiento

Impex

Impex MARCY SB-510 Manual de usuario

Impex

Impex MD-867 Manual de usuario

Impex

Impex MARCY MWB-9000 Manual de usuario

Impex

Impex Marcy Diamond MD-2109 Manual de usuario

Impex

Impex MARCY MCB-347 Manual de usuario

Impex

Impex PM-4510 Manual de usuario

Impex

Impex MARCY TSA 5000 Manual de usuario

Impex

Impex MARCY MKM-81030 Manual de usuario

Impex

Impex IGS-5100 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario