IHP HeatFlo Kit Manual de usuario

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1

GENERAL INFORMATION

The HeatFlo™ system is designed to redirect the convective heat

of the ﬁreplace from the front of the unit, above the glass, to

a location higher on the wall. The use of this kit allows for TV

installations closer to the ﬁreplace or in recessed wall cavities

above the ﬁreplace (see Tables 1 and 2, Page 3).

When Installing this kit, reference the framing dimensions and

follow the framing instructions shown on the ﬁreplace installation

Instructions. Follow all other installation requirements for the

ﬁreplace as detailed in the installation manual.

REFER TO INSTALLATION INSTRUCTIONS AND CARE AND

OPERATIONS MANUAL (IICO) FOR FRAMING DETAILS BEFORE

INSTALLING THIS KIT.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE FIREPLACE APPLY

TO THESE INSTRUCTIONS.

WARNING

This kit must be installed by a qualiﬁed installer,

service agency, or gas supplier at the time of the

ﬁreplace installation. These instructions must

be used in conjunction with the installation and

operation manual provided with the ﬁreplace.

INSTALLER: Leave this manual with the ﬁreplace.

CONSUMER: Retain this manual for future

reference.

HeatFlo™ Kit

INSTALLATION INSTRUCTIONS FOR HEATFLO KITS

[FOR USE WITH MODELS: Compass45TEN, CompassDLX45TEN, Compass55TEN, CompassDLX55TEN, DRL2000 45/55 and DRL3500 45/55]

HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 901068-00

REV. A 07/2021

Figure 1 - Kit Contents Overview

KIT CONTENTS (see Figure 1)

1 ea. Register Assembly

1 ea. Register Trim

4 ea. 4-1/2” x 24” Flex Pipe (stretches up to 70” in length)

8 ea. Gear Clamp

2 ea. Register Support Bracket

18 ea. Screws

4 ea. Collar Mounting Plate

4 ea. Small Collar

4 ea. Large Collar

1 ea. Hood

TOOLS / SUPPLIES REQUIRED (not included)

Electric Drill/Driver Gun

Phillips Screwdriver Bits

5/16 Nut Driver

3/8 Nut Driver

Wood Screws

HeatFlo™ Kit

Cat. No. Model Number Kit Name

F4454 HTFLO-DV45 Kit, HeatFlo 45 DV Units

F4453 HTFLO-DV55 Kit, HeatFlo 55 DV Units

Collar Mounting

Plates

Large Collars

Gear Clamps

Small Collars

Flex Pipes

Brackets

Figure 1

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

WARNING

Ensure clearances to combustibles are maintained when building a mantel or shelves above the fireplace.

Elevated temperatures on the wall or in the air above the fireplace can cause melting, discoloration or damage

to decorations, a television (TV) or other electronic components.

IMPORTANT NOTICE

Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may

negatively affect the longevity of the television and may negate the warranty. If you do place a television above the

ﬁreplace, please be aware of the large amount of heat generated by the ﬁreplace and consider placing the television

above the ﬁreplace at 12” minimum on a ﬂush wall and at 18" for a recessed installation, to reduce the amount of heat

that reaches the television. The homeowner must understand that IHP does not take responsibility for any negative

impact to televisions placed near this ﬁreplace.

FRAMING DIMENSIONS

Figure 2 - Fireplace Framing Dimensions For HeatFlo Installations - Flush Wall & Recessed Wall Pocket

Framing Dimensions - Inches (millimeters)

A B C D* E* F* G H

45” Models

45-7/8 (1165) 18 (458) 29 (737) 3-1/2 (89) 81-1/2 (2070) 1-1/2 (38) 43-1/2 (1105) 5-1/8 (130)

55” Models

55-7/8 (1420) 18 (458) 29 (737) 3-1/2 (89) 81-1/2 (2070) 1-1/2 (38) 53-1/2 (1359) 5-1/8 (130)

with HeatFlo Kit

forFlush Wall

with HeatFlo Kit

forRecessed Wall Pocket

with HeatFlo Kit

forFlush Wall

with HeatFlo Kit

forRecessed Wall Pocket

with HeatFlo Kit

for Flush Wall

with HeatFlo Kit

for Recessed Wall Pocket

NOTE: Unit must be installed a minimum of 6” off ﬂoor if the optional facade is to be installed.

D* Maximum allowable depth

E* Minimum height from appliance base to ceiling

F* Minimum distance from framed opening to ceiling

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3

Table 1 - Minimum Dimensions for Television (TV) Installed

Above Fireplace (Flush Wall)

(A) TV Above ﬁreplace Opening (Min.) 12” (305 mm)

(B) TV Below Heat Vent Opening (Min.) 3” (77 mm)

See Tables 1 and 2 for TVs Installed above the ﬁreplace:

WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to protect from

contact with hot surfaces.

Television (TV)

Fireplace

Ceiling

Wall

Base of Fireplace

HeatFlo

Opening

Min. 76”

(1930 mm)

Max. 20 ft.

(6.096 m)

Table 2 - Minimum Dimensions for Television (TV) Installed

Above Fireplace on a Recessed Wall Pocket

(A) Pocket Above Fireplace Opening (Min.) 18” (457 mm)

(B) Pocket Below Fireplace Opening (Min.) 5-1/2” (140 mm)

(C*) Vent Opening Below Ceiling 4” (102 mm)

* NOTE: Maximum pocket depth is 3-1/2” (89 mm)

Television (TV)

Fireplace

Ceiling

Wall

HeatFlo

Opening

Min. 76”

(1.930 m)

Max. 20 ft.

(6.096 m)

3" Min.

(All Sides)

Pocket *

TVs should not be used in situations where the actual TV temperature exceeds the manufacturer’s technical speciﬁcation. Contact

the TV manufacturer directly if you cannot locate this information or have questions regarding this information.

NOTE: Clearances to TV are provided only for guidance, please follow TV manufacturer’s recommendation for installation.

1-1/2”

4-1/2” DIA.

2-5/8”

1/2” FACING

3-1/2”

1”

6-1/4”

3-1/4”

1”

B C

11”

Figure 2

Inches (millimeters)

A B C D

45” Models

42-7/8

(1089)

(203)

(432)

44-5/8

(1133)

55” Models

52-7/8

(1343)

(305)

(508)

54-5/8

(1387)

Base of Fireplace

Figure 3 - Register Assembly and Trim

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

NOTICE

This kit must be installed by a qualiﬁed installer,

service agency, or gas supplier at the time of the

ﬁreplace installation. These instructions must

be used in conjunction with the installation and

operation manual provided with the ﬁreplace.

WARNING

DO NOT cover or place objects in front of the heat

opening within 76 inches above ﬂoor level as

discharge temperatures are hot!

WARNING

Minimum clearances below the ceiling is 4”. Note

that staining or streaking may occur on light colored

ceilings due to any dust, etc. in air ﬂow.

HEATFLO™ KIT INSTALLATION

FIREPLACE PREPARATION

NOTE: The installation of this HeatFlo system must be done at the

framing stage. Some work can be performed before the ﬁreplace

is placed in the framing, though installing the collars onto the

ﬁreplace must be done after to prevent interference with framing

header when placing ﬁreplace.

NOTE: Before the following steps are performed, it is recommended

to prepare the ﬁreplace top spacers, install the non-combustible

ﬁreboard standoffs, and install the header shield. Refer to ﬁreplace

installation instructions.

1. Remove four knockouts in ﬁreplace top and discard (Figure 4).

2. Remove four precut plugs in insulation between ﬁreplace top

and inner heat deﬂector (Figure 4).

3. Remove four knockouts from inner heat deﬂector (Figure 4).

4. Installﬁreplaceintoframingaccordingtotheﬁreplaceinstallation

instructions.

5. Insert four small collars into knockout openings in ﬁreplace top

with tabs up (Figure 5). Tabs should be resting on ﬁreplace top.

6. Place four large collars with ﬂange down on ﬁreplace top aligned

with small collars (Figure 5).

7. Place four collar mounting plates over large collars and attach

with screws provided (Figure 5).

8. Complete ﬁreplace preparation by removing ﬂat hood from

convection opening and replace with angled hood provided

(Figure 6).

Figure 4 Figure 5

Fireplace Top

Metal Knockout

Insulation Plug

Heat Deflector

Metal Knockout

Collar Mounting

Plate

Large Collar

Small Collar

Figure 4 Figure 5

Fireplace Top

Metal Knockout

Insulation Plug

Heat Deflector

Metal Knockout

Collar Mounting

Plate

Large Collar

Small Collar

Figure 4 - Knockout Removal

Figure 6 - Hood Removal / Installation

Figure 5 - Collar Installation

NOTE: Flat hood (shown) must be replaced with angled hood provided in kit.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5

Figure 7 - Placing Register Assembly

HEATFLO INSTALLATION

1. Mount the register into the framed opening by tilting forward and

inserting from the back while rotating into place with register

resting on lower stud of framed opening (Figures 7 and 8).

2. Attach register top mounting ﬂange to top of framed opening

using screws (Figure 10).

NOTE: Top mounting ﬂange is not intended to carry all the weight.

The register rests on the lower stud of the framed opening and

support brackets.

3. Ensure the register is leveled and its outlet is not distorted,

then secure using support brackets (Figures 8 and 9). Support

brackets must be secured to both register and framing.

4. With ﬁreplace and register fully secured, attach the provided ﬂex

pipes to the collars on ﬁreplace and secure with provided gear

clamps (Figure 11).

5. Stretch ﬂex pipe to slightly less than desired length.

6. With the ﬂex pipes attached to ﬁreplace, connect the ﬂex pipes to

7. After wall ﬁnishing and facing details are completed, attach trim

to register on both sides with provided screws.

Insert Register From

Back of Framing and

Rotate into Place

Sprinkler Head

60” Min.

4” Min.

Vent Opening Protrudes

from Framing 1/2”

1” Min. Clearance to Combustibles

Around All Pipes

Level Register and

Secure to Framing

Insert Register From

Back of Framing and

Rotate into Place

Sprinkler Head

60” Min.

4” Min.

Vent Opening Protrudes

from Framing 1/2”

1” Min. Clearance to Combustibles

Around All Pipes

Level Register and

Secure to Framing

Figure 8 - Register Clearances

Figure 9 - Installing Support Brackets

Secure Support Brackets

to Register and Framing

Rear Framing

Figure 9

Figure 10 - Securing Register Front View

Figure 10

Attach Register Top Mounting Flange with Screws

Rests on

Framing

2x4 Framing on Edge

NOTES:

• DO NOT SLICE OR RUPTURE FLEX PIPES!

• Flex pipe stretches up to 2.9 times its compressed length (i.e.,

24” long pipe will stretch to approximately 70” maximum).

• Minimum allowed distance from base of ﬁreplace to register vent

opening is 76”. Maximum is 20ft.

• Maintain 1” min. clearance to combustibles around ﬂex pipes.

• Keep ﬂex pipes as vertical as possible to maintain airﬂow.

• Do not let ﬂex pipes contact ﬁreplace venting.

•NOTE: Trim has 1” of adjustment to allow for different thickness

of facing materials.

WIRING NOTE: Do Not let ﬂex pipes come in contact with any

type of wiring.

CAUTION: Flex pipe should be stretched out from its compressed state

before installation. DO NOT over stretch the Flex. Make sure the ﬂex pipe

is slightly loose (but not sagging) when installed to allow for expansion

and contraction. Flex pipe must not come in contact with combustible

materials. Excessively loose ﬂex could contact combustible materials

and cause a ﬁre hazard.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 13 - HeatFlo Kit Installed

Figure 11 - Installing Flex Pipe to Fireplace

Figure 11

Flex

Pipe

Gear

Clamp

HeatFlo

Collar

Figure 13

Flex Pipes

Stretched

into Place

Maintain 1” Min.

Clearance Around

Flex Pipes

Gear Clamp

3/8” Hex Head Screw

for Attaching Trim to

Heat Register

3/8” Hex Head

Screw for

Attaching Trim to

Heat Register

HeatFlo collar

HeatFlo

HeatFlo Trim

4-1/2" Flex pipe

(Stretches up to

approximately 70")

Figure 12 - Installing Flex Pipe to Heat Register

CAUTION: Flex pipe should be stretched out from its compressed state before installation. DO NOT over stretch the Flex.

Make sure the ﬂex pipe is slightly loose (but not sagging) when installed to allow for expansion and contraction. Flex

pipe must not come in contact with combustible materials. Excessively loose ﬂex could contact combustible materials

and cause a ﬁre hazard.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7

FINISHING FIREPLACE

The appliance is designed to mate with 1/2” wall sheathing materials such

as drywall, plywood, wood composites, or non-combustible materials.

Finishing and Sealing Joints

All joints between the ﬁnished wall sheathing and the appliance must be

sealed with non-combustible materials. Sealants, such as caulk or mastic

used to seal the gap between the wall and the ﬁreplace, should be rated

at a minimum continuous exposure to 300 ºF.

Finishing Around Opening with Gypsum Wallboard

Gypsum wallboard (drywall) joints adjacent to the ﬁreplace opening,

including the non-combustible board on the appliance, require special

attention to minimize cracking. When installing gypsum wallboard around

the ﬁreplace, install the hole for the ﬁreplace opening in a single wallboard

sheet, if possible. This will minimize the joints adjacent to the ﬁreplace

opening.

Tape wall board joints around the ﬁreplace opening with ﬁberglass-mesh

tape. It will provide a more crack-resistant joint than paper tape. Fill, smooth

and ﬁnish wall joints with chemically setting-type joint compound. It will

provide a more crack-resistant joint than air-drying light-weight compound.

NOTE: NEVER install combustible material (wall ﬁnish, surround, trim,

etc.) on, in front of, or overlapping any part of the ﬁreplace front face.

NOTE: The HeatFlo Register Trim ships from the factory painted black

and it may be painted another color to match the wall color. Use high

temperature paint with a minimum 400°F continuous rating. Do not ﬁnish

over any of the opening in the trim outlet.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

P/N 901068-00 REV. A 07/2021

Innovative Hearth Products (IHP) reserves the right to make changes at any time, without

notice, in design, materials, speciﬁcations, prices and also to discontinue colors, styles and

products. Consult your local distributor for ﬁreplace code information.

1769 East Lawrence Street • Russellville, AL 35654

Tabla de contenidos

Otros manuales de Accesorios para chimeneas de IHP

IHP

IHP DWLS-RNCL35 Manual de usuario

IHP

IHP Superior 900347-00 Manual de usuario

IHP

IHP RDV-BRK-STD Manual de usuario

IHP

IHP STK-LIN60-B KIT Manual de usuario

IHP

IHP UZY-7-B Manual de usuario

IHP

IHP PURFIRE AH1924 Manual de usuario

IHP

IHP SV4.5-TWSK Manual de usuario

IHP

IHP Montebello Series Manual de usuario

IHP

IHP F1762 Manual de usuario

IHP

IHP F2460 Manual de usuario

IHP

IHP VF F3784 Manual de usuario

IHP

IHP DEL SOL Manual de usuario

IHP

IHP BNZN Manual de usuario

IHP

IHP SEREFINA CI1500 GCK LP Manual de usuario

IHP

IHP 900077-07 Manual de usuario

IHP

IHP MERIT ZEN GARDEN MLDVTCD-35 Manual de usuario

IHP

IHP LPDBK Manual de usuario

IHP

IHP PCBM-42 Manual de usuario

IHP

IHP AK4 Manual de usuario

IHP

IHP BWBK Manual de usuario

IHP

IHP RDV-CONTF-BLK Manual de usuario

IHP

IHP PCBE-36 Manual de usuario

IHP

IHP 900935-00 Manual de usuario

IHP

IHP F2624 Manual de usuario

Manuales populares de Accesorios para chimeneas de otras marcas

Valor

Valor L2 1700K Manual de usuario

Exodraft

Exodraft Xzense Manual de usuario

Whalen

Whalen Ruso MNFP62BF23-6 Manual de usuario

Lopi

Lopi Hearthview 864 Manual de usuario

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manual de usuario

EdilKamin

EdilKamin SERBATOIO 250 Guía de inicio rápido

Bronpi

Bronpi KIT-1 Manual de usuario

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manual de usuario

Travis Industries

Travis Industries 33 DVI Manual de usuario

Superior

Superior ASD3628-TI Manual de usuario

pleasant hearth

pleasant hearth OFP28WG Manual de usuario

Firegear

Firegear FG-H-2110SS Manual de usuario

Nibe

Nibe Contura C i31 Manual de usuario

kozy heat

kozy heat KZK-052 Manual de usuario

SimpliFire

SimpliFire SF-WM36 Manual de usuario

Bluegrass Living

Bluegrass Living BC18NR Guía de inicio rápido

pleasant hearth

pleasant hearth IRIS SCROLL Manual de usuario

Cooke

Cooke Glass Wind Guard Manual de usuario