IHP SV4.5-TWSK Manual de usuario

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios para chimeneas de IHP

Manuales populares de Accesorios para chimeneas de otras marcas

Valor

Valor L2 1700K Manual de usuario

Exodraft

Exodraft Xzense Manual de usuario

Whalen

Whalen Ruso MNFP62BF23-6 Manual de usuario

Lopi

Lopi Hearthview 864 Manual de usuario

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manual de usuario

EdilKamin

EdilKamin SERBATOIO 250 Guía de inicio rápido

Bronpi

Bronpi KIT-1 Manual de usuario

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manual de usuario

Travis Industries

Travis Industries 33 DVI Manual de usuario

Superior

Superior ASD3628-TI Manual de usuario

pleasant hearth

pleasant hearth OFP28WG Manual de usuario

Firegear

Firegear FG-H-2110SS Manual de usuario

Nibe

Nibe Contura C i31 Manual de usuario

kozy heat

kozy heat KZK-052 Manual de usuario

SimpliFire

SimpliFire SF-WM36 Manual de usuario

Bluegrass Living

Bluegrass Living BC18NR Guía de inicio rápido

pleasant hearth

pleasant hearth IRIS SCROLL Manual de usuario

Cooke

Cooke Glass Wind Guard Manual de usuario

THROUGH-WALL

SHIELD KIT

HEARTH PRODUCTS

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR THE THROUGH-WALL SHIELD KIT

(MODEL NUMBER: SV4.5-TWSK) (CATALOG NUMBER: H5816)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

P/N 750247M

REV. A 05/2014

GENERAL INFORMATION

The Through-Wall Shield may be used to shield the Direct Vent Pipe from

blown insulation where required. It is critical to maintain the airspace

clearance free from any material between the shield and the pipe.

If you encounter any problems, need clariﬁcation of these instructions

or are not qualiﬁed to properly install this kit, contact you local distribu-

tor or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUALS PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

INSTALLATION INSTRUCTIONS

Step 1. Cut the Through-Wall Shield to the desired length.

Step 2. Bring both ends of the Through-Wall Shield together to form a

cylinder (see Figure 1).

Step 3. Insert all the remaining locking tabs into the corresponding slots

and bend the tabs inwards to prevent the Through-Wall Shield

from disengaging. Refer to Section “A”-“A” of Figure 1.

Step 4. Bend the mounting tabs (with holes) outwards on the Through-

Wall Shield (see Figure 2).

Step 5. Bend the locating tabs inward on the Through-Wall Shield (see

Figure 3).

Step 6. Position the Through-Wall Shield on the ﬁrestop spacer and

center it by placing the locating tabs to the edge of the circular

opening on the ﬁrestop spacer (see Figure 3).

Step 7. While keeping the Through-Wall Shield centered on the ﬁrestop

spacer opening, drive a screw on each of the four (4) mounting

tabs of the Through-Wall Shield into the ﬁrestop spacer (refer

to Figure 3).

NOTE: To ensure that the screws will not interfere with the termination

assembly, place the Through-Wall Shield so the seam is located at 12 or

6 o’clock (see Figure 4).

Figure 1

Figure 2

Through-Wall Shield

"A" "A"

SECTION "A" - "A"

Firestop

Securing Screws - Four (4)

Through-Wall Shield

Mounting Tabs

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Printed in U.S.A. © 2007 IHP LLC

P/N 750247M REV. A 05/2014

Figure 3 Figure 4

Mounting Tabs

Four (4) Places

Locating Tabs

Four (4) Places

Through-Wall Shield Seam

Located At 12 Or 6 O’Clock

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local

distributor for ﬁreplace code information.

fire-parts.com