IHP PURFIRE AH1924 Manual de usuario
Figure 1 - Masonry Fireplaces
Figure 2 - Factory Built Fireplaces
PURFIRE™ ADJUSTABLE EMISSION CONTROL HOOD KITS
[FOR USE WITH MASONRY AND FACTORY BUILT WOOD-BURNING FIREPLACES]
PURFIRE™ ADJUSTABLE EMISSION
CONTROL HOOD KITS
P/N 127124-01
Rev. B, 04/2017
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. Adjustable Hood
4 ea. Mounting Screws
1 ea. Instruction Sheet
PureFire™ Aftermarket Adjustable Emission Control Hood Kits
Cat. No. Model Description
F0878 AH1924 Adjusts to fireplace back wall measuring 19"-24"
F0879 AH2231 Adjusts to fireplace back wall measuring 22"-31"
F0880 AH3143 Adjusts to fireplace back wall measuring 31"-43"
GENERAL INFORMATION
The PureFire Catalytic Hood can be installed in a wood burning
masonry fireplace or a factory built zero clearance fireplace. The
PureFire Catalytic Hood can easily be installed in less than an
hour. Four mounting screws will hold the two mounting brack-
ets in place. Included with the hood are two sets of mounting
brackets (for masonry fireplace or factory-built fireplace). The
PureFire Catalytic Hood has a trapezoidal shape to fit the angu-
lar sides of the firebox. The hood is equipped with adjustable
extensions that slide in and out. The PureFire Catalytic Hood
should be installed after the fireplace is completely finished. It
is designed to be installed as an add-on device. It is mounted on
two brackets that are mechanically attached to the side walls of
the firebox. Ensure that the firebox is structurally sound before
beginning the installation.
READ ALL THE STEPS BEFORE STARTING THE CONVERSION. IN-
STALLER NOTICE: THESE INSTRUCTIONS MUST BE LEFT WITH THE
APPLIANCE.
THE APPLIANCE MUST BE OFF AND COLD BEFORE PERFORMING
THE INSTALLATION.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-
LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE
APPLY TO THESE INSTRUCTIONS.
INSTALLATION INSTRUCTIONS
For Masonry fireplace application, the retainer brackets are
attached to the firebrick on the side walls (see Figure 1). For
factory-built fireplace application, the retaining bracket rest or
is above the top edge of firebrick (see Figure 2).
WARNING: STOP: Before installation of this prod-
uct your chimney must be cleaned by a professional
chimney sweep.
1
IHP.us.com
Self-Drilling
Sheet Metal Screw
Top Edge
of Firebrick
End Tab
Masonry
Screw
Left Hand
Side Shown
End Tab
Left Hand
Side Shown
IHP.us.com
2
Figure 3 - PureFire Catalytic Hood Installed (Top View)
Figure 4 - PureFire Catalytic Hood Installed (Side View)
The height of the bracket installation is determined by the fire-
place opening. The brackets should be installed so they are
even or above the height of the fireplace opening (lintel) or the
smoke shelf. The brackets can be used to identify the location
of the mounting screw holes. A black felt tip should be used
to identify the location for drilling. Two holes will need to be
drilled on each side of the firebox. For masonry application, the
brackets are attached using masonry screws (provided). For
factory-built fireplace application, brackets are attached using
self-drilling sheet metal screws (provided). Make sure that the
brackets are installed as shown. The bracket end tab should be
facing the front of the firebox. The end tab will prevent the hood
from moving. After the brackets are installed, the hood should
be adjusted to the correct dimension to properly fit into the
brackets. Measure the distance between the installed brackets
on both front and back. Move the adjustable extensions on the
hood until the front and back on the hood extensions equal the
dimensions of the mounting brackets. Tighten the retention
screws on each side of the hood.
The PureFire Catalytic Hood can now be installed in the fire-
box. Position the hood in the brackets so that it is securely in
place. The PureFire Catalytic Hood should be located against
the back wall of the firebox directly above the grate (see Figure
3). Minimum Distance between the leading edge of the smoke
shelf and the hood is 6" (see Figure 4). The damper Handle
(if required) should pass between the combustor blocks and
remain operational. Chain operated units will have the chain
in front of the hood.
The HearthCAT™ emission control system is now
ready for use.
Hearth Cat Hood
6"
Minimum
Smoke
Shelf
Damper Blade
Printed in U.S.A. © 2014 Innovative Hearth Products
P/N 127124-01 Rev. B 04/2017
IHP reserves the right to make changes at any time, without notice, in design, materials, specifica-
tions, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
Este manual sirve para los siguientes modelos
5
Otros manuales de Accesorios para chimeneas de IHP
IHP
IHP GCKSMS557051NP Manual de usuario
IHP
IHP PCBE-324 Manual de usuario
IHP
IHP Superior 900347-00 Manual de usuario
IHP
IHP RDV-BRK-STD Manual de usuario
IHP
IHP H5872 Manual de usuario
IHP
IHP PCBM-325 Manual de usuario
IHP
IHP SECURE FLEX SF-12 Manual de usuario
IHP
IHP AK4 Manual de usuario
IHP
IHP PCBE-42 Manual de usuario
IHP
IHP MAGNIFLAMEOD24NE Guía de inicio rápido
IHP
IHP F1762 Manual de usuario
IHP
IHP RDV-CONTF-BLK Manual de usuario
IHP
IHP PCBE-36 Manual de usuario
IHP
IHP FP6820-4S-DVFP Manual de usuario
IHP
IHP SEREFINA CI1500 GCK LP Manual de usuario
IHP
IHP MERIT ZEN GARDEN MLDVTCD-35 Manual de usuario
IHP
IHP RIVROCK-25PK Manual de usuario
IHP
IHP Snap-Pak Manual de usuario
IHP
IHP EPIC-TRIM-B Manual de usuario
IHP
IHP 900935-00 Manual de usuario
Manuales populares de Accesorios para chimeneas de otras marcas
Bronpi
Bronpi KIT-1 Manual de usuario
Town & Country Fireplaces
Town & Country Fireplaces 22150051 Manual de usuario
Travis Industries
Travis Industries 33 DVI Manual de usuario
Superior
Superior ASD3628-TI Manual de usuario
pleasant hearth
pleasant hearth OFP28WG Manual de usuario
Firegear
Firegear FG-H-2110SS Manual de usuario
