IFM O5E7 Series Manual de usuario

Operating instructions

Through-beam sensor

O5E7xx

O5S7xx

80284275 / 00 04 / 2019

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR

1040 except for deviations pursuant to Laser Notice No. 50, dated June

2007

Position of the product label Additional label

3 Functions and features

The through-beam sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range 60 m.

4 Installation

transmitter receiver

►Install the receiver (O5E...) and secure it to a bracket.

►Align the transmitter (O5S...) to the receiver and fix it.

Maximum range is only possible with precise alignment.

5 Operating and display elements

receiver







1: LED

2: [OUT on]

3: [OUT o󰀨]

6 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of

electrical equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

Receiver DC PNP











pin 1 = L+ (10...36 V DC)

(pin 2 = not connected)

pin 3 = L-

pin 4 = load (PNP, 200 mA)

Transmitter DC

L+

pin 1 = L+ (10...36 V DC)

(pin 2 = not connected)

pin 3 = L-

(pin 4 = not connected)

7 Settings

7.1 The sensor is to switch when the object is detected

►Position the object

receiver transmitter

►Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The yellow LED flashes.

►Remove the object

receiver transmitter

►Press [OUT off].

> The sensitivity is set without object.

> The yellow LED goes out. The programming is finished.

7.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off].

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

7.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

7.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz.

• Measured value difference too small.

• Max. programming time of 15 min. exceeded.

7.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

8 Operation

►Check whether the units operate correctly.

> Receiver: The LED lights when the switching output is switched.

9 Maintenance, repair and disposal

►Keep the front panes of the sensors free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at www.ifm.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM PN422 Series Manual de usuario

IFM

IFM O3D300 Manual de usuario

IFM

IFM PN78 Series Manual de usuario

IFM

IFM UGT203 Manual de usuario

IFM

IFM Efector 200 O4P5 Series Manual de usuario

IFM

IFM LDH100 Manual de usuario

IFM

IFM UGR500 Manual de usuario

IFM

IFM O3D3 Series Manual de usuario

IFM

IFM KI0054 Manual de usuario

IFM

IFM Efector 500 PNI02X Manual de usuario

IFM

IFM VSP003 Manual de usuario

IFM

IFM Efector200 OJ51 Series Manual de usuario

IFM

IFM Efector 200 O7E2 Series Manual de usuario

IFM

IFM KQ10 Series Manual de usuario

IFM

IFM PI17 Series Manual de usuario

IFM

IFM SB1 Series Manual de usuario

IFM

IFM Efector 100 GG712S Manual de usuario

IFM

IFM efector200 OM Manual de usuario

IFM

IFM Efector 200 OJ Manual de usuario

IFM

IFM PQ78 Series Manual de usuario

IFM

IFM OG Manual de usuario

IFM

IFM OGE Manual de usuario

IFM

IFM Efector 200 OGH2 Series Manual de usuario

IFM

IFM O5D15 Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario