IFM O5D15 Series Manual de usuario

Operating instructions

Optical distance sensor

O5D15x UK

80284257 / 00 04 / 2019

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

3�1 Applications ��4

4 Installation��5

4�1 Installation conditions ��5

5 Operating and display elements ��5

6 Electrical connection��6

7 Settings��7

7�1 The sensor is to switch when the object is detected��7

8 IO-Link ��7

8�1 General information ��7

8�2 Device-specific information��7

8�3 Parameter setting tools��7

9 Operation��8

9�1 Electronic lock��8

9�2 Fault indications��8

10 Maintenance, repair and disposal��9

1 Preliminary note

1.1 Symbols used

►Instructions

> Reaction, result

[…] Designation of keys, buttons or indications

→Cross-reference

Important note

Non-compliance may result in malfunction or interference�

2 Safety instructions

• The device described is a subcomponent for integration into a system�

- The manufacturer of the system is responsible for the safety of the system�

- The system manufacturer undertakes to perform a risk assessment and to

create a documentation in accordance with legal and normative requirements

to be provided to the operator and user of the system� This documentation

must contain all necessary information and safety instructions for the operator,

the user and, if applicable, for any service personnel authorised by the

manufacturer of the system�

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ Functions and features).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the unit

must be carried out by qualified personnel authorised by the machine operator�

• Protect units and cables against damage�

According to cULus

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure�

Visible laser light; CLASS 1 LASER PRODUCT�

EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR

1040 except for deviations pursuant to Laser Notice No� 50, dated June

2007

Position of the product label Warning sign

LASER KLASSE 1

CLASS 1 LASER PRODUCT

APPAREIL A LASER CLASSE 1

3 Functions and features

The unit is used as an optical distance sensor�

3.1 Applications

• The optical distance sensor measures distances between 0�03 and 2 m�

• It has a background suppression of up to 20 m�

• The switching outputs are complementary�

The distance between the sensor and the background must be limited

to max� 20 m by the customer� Otherwise measured values can be

ambiguous → 4.1 Installation conditions.

4 Installation

4.1 Installation conditions

►Install the unit so that the object to be detected is within a measuring range of

0�03��2 m�

Any object between the set switch point and a distance of 20 m from the sensor is

suppressed�

Reflecting surfaces in the direct beam path of the sensor – also in

the range > 20 m – are to be avoided by the customer� Otherwise the

measured values can be ambiguous�

5 Operating and display elements

1: LED green: operation

2: LED yellow: switching status

3: 3-digit alphanumeric display

4: Range +

5: Range -

6 Electrical connection

The unit must be connected by a qualified electrician�

►The national and international regulations for the installation of

electrical equipment must be adhered to�

►Ensure voltage supply to EN 50178�

►Disconnect power�

►Connect the unit as follows:

DC PNP

























4: OUT1 = normally open / IO-Link

2: OUT2 = normally closed

DC NPN

























4: OUT1 = normally open / IO-Link

2: OUT2 = normally closed

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

7 Settings

7.1 The sensor is to switch when the object is detected

►Position the object�

►Press [+] to increase the range�

> The set distance value is shown flashing in the display�

> The yellow LED lights when the object is detected�

►Press [-] to decrease the distance value�

> The set distance value is shown flashing in the display�

> During operation, the currently detected distance value is shown in the display�

8 IO-Link

8.1 General information

This unit has an IO-Link communication interface which requires an IO-Link-

capable module (IO-Link master) for operation.

The IO-Link interface enables direct access to the sensor values and parameters

and provides the possibility to set the parameters of the unit during operation�

In addition communication is possible via a point-to-point connection with a USB

adapter cable�

You will find more detailed information about IO-Link at www�ifm�com�

8.2 Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link device and

detailed information about sensor values, diagnostic information and parameters

in the overview table at www�ifm�com�

8.3 Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�ifm�com�

9 Operation

►Check whether the unit operates correctly�

> The LED lights when the switching output is switched�

> The detected distance value is shown in the display�

9.1 Electronic lock

The unit can be locked electronically to prevent unauthorised setting� On delivery

the unit is not locked�

Locking

►Make sure that the unit is in the normal operating mode�

►Keep [+] + [-] pressed until [Loc] is displayed�

> The unit is locked�

Unlocking

►Keep [+] + [-] pressed until [uLo] is displayed�

> The unit is unlocked�

9.2 Fault indications

Display Possible cause Switching output

[Hno] [Hnc]

[++] Too much light,

e�g� reflective surfaces ON OFF

[--] Not enough light, no object OFF ON

[nEA] Object to be measured outside the

measuring range < 30 mm ON OFF

[FAr] Object to be measured outside the

measuring range > 2500 mm OFF ON

[ERP] Plausibility (e.g. object too fast) unchanged unchanged

[SC] Short circuit at the switching output

10 Maintenance, repair and disposal

► Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material�

►Do not open the module housing� There are no user-serviceable components

inside�

Technical data and further information at www�ifm�com

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM O6E7 Series Manual de usuario

IFM

IFM EC2061 Manual de usuario

IFM

IFM O1D120 Manual de usuario

IFM

IFM OY4**S Series Manual de usuario

IFM

IFM O2D54 Series Manual de usuario

IFM

IFM efector200 O6P2 Manual de usuario

IFM

IFM SI 5000 Manual de usuario

IFM

IFM PN3 Series Manual de usuario

IFM

IFM LDL100 Manual de usuario

IFM

IFM O5D10 Series Manual de usuario

IFM

IFM OMH551 Manual de usuario

IFM

IFM Efector 200 O4P5 Series Manual de usuario

IFM

IFM efector160 LR2750 Manual de usuario

IFM

IFM VNB211 Manual de usuario

IFM

IFM O5H5xA Series Manual de usuario

IFM

IFM Efector 500 PI30 Manual de usuario

IFM

IFM OJ51 Series Manual de usuario

IFM

IFM LW2120 Manual de usuario

IFM

IFM Efector 500 PNI02X Manual de usuario

IFM

IFM O3M150 Instrucciones de montaje

IFM

IFM Efector200 OJ51 Series Manual de usuario

IFM

IFM PI16 Series Manual de usuario

IFM

IFM Efector 200 Series Manual de usuario

IFM

IFM O1D100 series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario