IFM PN422 Series Manual de usuario

Operating instructions
Pressure sensor
PN422x
11426187 / 00 01 / 2022
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������3
1�1 Symbols used ������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
3 Functions and features ����������������������������������������������������������������������������������������4
4 Function���������������������������������������������������������������������������������������������������������������5
4�1 Switching function������������������������������������������������������������������������������������������5
5 Installation������������������������������������������������������������������������������������������������������������6
5�1 Installation of the sensor��������������������������������������������������������������������������������6
5�2 Installation of the grounding clamp����������������������������������������������������������������6
6 Electrical connection��������������������������������������������������������������������������������������������8
7 Operating and display elements ������������������������������������������������������������������������10
8 Menu������������������������������������������������������������������������������������������������������������������ 11
8�1 Menu structure��������������������������������������������������������������������������������������������� 11
8�2 Explanation of the menu������������������������������������������������������������������������������12
9 Parameter setting ����������������������������������������������������������������������������������������������12
9�1 Parameter setting in general �����������������������������������������������������������������������12
9�2 Set output signals ����������������������������������������������������������������������������������������14
9�2�1 Set switching limits �����������������������������������������������������������������������������14
9�2�2 Setting of the output function��������������������������������������������������������������14
9�3 User settings (optional)��������������������������������������������������������������������������������14
9�3�1 Set the unit of measurement for system pressure������������������������������14
9�3�2 Configuration of the display ����������������������������������������������������������������14
9�3�3 Zero-point calibration��������������������������������������������������������������������������15
9�3�4 Set delay time for OUT1 ���������������������������������������������������������������������15
9�3�5 Setting the damping for OUT1 �����������������������������������������������������������15
9�4 Service functions �����������������������������������������������������������������������������������������15
9�4�1 Read min/max values for the system pressure ����������������������������������15
10 Operation���������������������������������������������������������������������������������������������������������16
10�1 Operating indicators ����������������������������������������������������������������������������������16
10�2 Read set parameters ���������������������������������������������������������������������������������16
10�3 Error indications�����������������������������������������������������������������������������������������16

3
UK
1 Preliminary note
1.1 Symbols used
►Instructions
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunction or interference�
Information
Supplementary note�
2 Safety instructions
• The device described is a subcomponent for integration into a system�
- The manufacturer is responsible for the safety of the system�
- The system manufacturer undertakes to perform a risk assessment and to
create a documentation in accordance with legal and normative requirements
to be provided to the operator and user of the system� This documentation
must contain all necessary information and safety instructions for the operator,
the user and, if applicable, for any service personnel authorised by the
manufacturer of the system�
• Read this document before setting up the product and keep it during the entire
service life�
• The product must be suitable for the corresponding applications and
environmental conditions without any restrictions�
• Only use the product for its intended purpose (→ Functions and features).
• Only use the product for permissible media (→ Technical data).
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property may occur�
11 Technical data and scale drawing ��������������������������������������������������������������������16
12 Factory setting �������������������������������������������������������������������������������������������������17

4
• The manufacturer assumes no liability or warranty for any consequences
caused by tampering with the product or incorrect use by the operator�
• Installation, electrical connection, set-up, programming, configuration, operation
and maintenance of the product must be carried out by personnel qualified and
authorised for the respective activity�
• Protect units and cables against damage�
• Use in gases at pressures > 25 bar only on request�
3 Functions and features
The pressure sensor detects the system pressure�
• It is shown on a display�
• It generates 1 output signal according to the set output configuration:
OUT1 = switching signal for system pressure limit value�
Applications
Type of pressure: relative pressure
Information on pressure rating and bursting pressure → data sheet.
Pressure Equipment Directive (PED): Units with a final value of the
measuring range of 1���400 bar comply with section 3, article (3) of the
Directive 97/23/EC and are designed and manufactured for group 2 fluids
(stable gases and non-superheated liquids) in accordance with the sound
engineering practice�
Avoid static and dynamic overpressure exceeding the specified overload
pressure by taking appropriate measures�
The indicated bursting pressure must not be exceeded�
Even if the bursting pressure is exceeded only for a short time, the unit
may be destroyed� ATTENTION: Risk of injury!
Use in gases at pressures > 25 bar only on request�
Indication of the current system pressure as from 1% of the final value
of the measuring range� Display “0%” does not mean that no pressure is
applied to the system!

5
UK
4 Function
4.1 Switching function
OUT1 changes its switching state if it is above or below the set switching limits
(SP1, rP1)� The following switching functions can be selected:
• Hysteresis function / normally open: [OU1] = [Hno] (→ Fig. 1).
• Hysteresis function / normally closed: [OU1] = [Hnc] (→ Fig. 1).
First the set point (SP1) is set, then the reset point (rP1) with the requested
difference�
• Window function / normally open: [OU1] = [Fno] (→ Fig. 2).
• Window function / normally closed: [OU1] = [Fnc] (→ Fig. 2).
The width of the window can be set by means of the difference between SP1 and
rP1� SP1 = upper value, rP1 = lower value�
1 2
P = system pressure; HY = hysteresis; FE = window

6
5 Installation
5.1 Installation of the sensor
Before installing and removing the unit: Make sure that no pressure is
applied to the system�
►Insert the unit in a process connection with a suitable thread�
►Tighten firmly�
Tightening Torque 1/4-18 NPT threads: 2���3 turns after finger tightened�
To ensure leak-free joints for NPT threads, sealants and lubricants
commonly used in the industry should be used�
5.2 Installation of the grounding clamp
If installed in an ungrounded pipe system (e�g� plastic pipes), the unit
must be grounded� The grounding clamp (order no� E43321) serves this
purpose� It is designed to discharge noise voltages in case the sensor is
mounted to ungrounded installations� It is available as an accessory and to
be used preferably on PN42xx series sensors�
The earthing strap and the clamping device must be in contact with the
sensor sleeve outside of the area where the type label is!
►Attach the clamping device
of the grounding clamp to the
sensor in the area beneath the
M12 connector (A)�
►Bend the earthing strap around
the sensor sleeve and insert
it in the slot of the clamping
device (B)�
AB

7
UK
►Push the earthing strap into the
clamping device until it is in close
contact with the sensor sleeve�
►Use an adequate screwdriver to tighten
the lower screw until the earthing strap
can no longer be moved on the sensor
sleeve (C)�
►Make sure that the washer is fitted on
the upper screw�
►Fasten the ground cable with the upper
screw and an adequate screwdriver to
the clamping device (D)�
C
D

8
6 Electrical connection
• The unit must be connected by a qualified electrician�
• The national and international regulations for the installation of electrical
equipment must be adhered to�
• For the output circuit, the same protective measures as for the supply
circuit must be taken� Insert a miniature fuse according to IEC60127-2
Sheet 1 (5 A fast acting)�
• The permissible potential difference between supply and output circuit is
max� 300 V�
• The equalisation of potential of metal housing parts must be ensured via
the sensor housing� Ensure an electrically conductive connection� The
grounding clamp (order no� E43321) can be used for the equalisation of
potential�
• Due to the integrated EMC filters, leakage currents of typ� < 0�5 mA can
flow via the potential equalisation to the earth potential�
• If several units are used in parallel, take into account that the leakage
currents add�
• The applicable standards must be adhered to�
Touchable surfaces of the unit are insulated to the circuits with double or
reinforced insulation according to IEC 61010-1 to overvoltage category III
and rated operating voltage 300 VAC�

9
UK
►Disconnect power�
►Connect the unit as follows:
Connector view
(at the unit)
A: Supply circuit
B: Output circuit
: Safe separation
Core colours of ifm sockets:
1 = BN (brown), 2 = BU (blue), 4 = BK (black), 5 = WH (white)

10
7 Operating and display elements
1: 7-segment display
- Display of the current system pressure 1)�
- Indication of the parameters and parameter values�
2: LED red
Indication of the switching status; lights when the output is switched�
3: Set button
- Setting of the parameter values (scrolling by holding pressed; incremental by pressing
briefly)�
4: Mode/Enter button
- Selection of the parameters and acknowledgement of the parameter values�
1) PSI value in case of units with a measuring range > 999 PSI = displayed value × 10
Tabla de contenidos
Otros manuales de Accesorios de IFM

IFM
IFM UGR500 Manual de usuario

IFM
IFM LR7009 Manual de usuario

IFM
IFM O2D51 Series Manual de usuario

IFM
IFM O1D100 series Manual de usuario

IFM
IFM IFS Series Manual de usuario

IFM
IFM PL205 Series Manual de usuario

IFM
IFM SBT633 Manual de usuario

IFM
IFM JD Series Guía de aplicación

IFM
IFM PT24 Series Manual de usuario

IFM
IFM KI0058 Manual de usuario

IFM
IFM LDL100 Manual de usuario

IFM
IFM O5H5 Series Manual de usuario

IFM
IFM OGE7 Series Manual de usuario

IFM
IFM OID20 Series Manual de usuario

IFM
IFM UIT510 Manual de usuario

IFM
IFM LK 022 Series Manual de usuario

IFM
IFM OY Series Manual de usuario

IFM
IFM DTI424 Manual de usuario

IFM
IFM SDP110 Manual de usuario

IFM
IFM GI854S Manual de usuario





















