IFM O4E5 Series Manual de usuario

Operating instructions

Through-beam sensor

O4E5xx / O4S5xx

11473682 / 00 11 / 2012

UKUK

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Functions and features

The through-beam sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range: → type label.

3 Installation

transmitter receiver

►Install the receiver (O4E...) and secure it to a bracket.

►Align the transmitter (O4S ...) to the receiver and secure it in the same way.

Maximum range only with accurate alignment.

4 Operating and display elements

1: LED yellow

2: [OUT on] button

3: [OUT o󰀨] button

receiver

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of

electrical equipment must be adhered to.

►Ensure voltage supply to EN 50178.

►Disconnect power.

►Connect the unit as follows:

Transmitter connector

L+

pin 1 = L+

(pin 2: not connected)

pin 3 = L-

(pin 4: not connected)

Transmitter cable *









BN = L+

BU = L-

Receiver connector











pin 1 = L+

(pin 2 = not connected)

pin 3 = L-

pin 4 = load

Receiver cable *











BN = L+

BU = L-

BK = load

* Core colours: BN = brown, BU = blue, BK = black

6 Setting

6.1 Sensitivity setting

The sensor is to switch when the object is detected

►Position the object.

receiver transmitter

►Press [OUT on] for 2 s.

> The sensitivity is set to the object. The yellow LED flashes.

►Remove the object.

receiver transmitter

►Press [OUT off].

> The sensitivity is set without object.

> The yellow LED goes out. The setting operation is completed.

The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off].

►Remove the object (see figure 2) and press [OUT on].

You can carry out the setting first without object and then with object.

6.2 Setting of maximum sensitivity

►Interrupt the light beam.

The sensor is to switch when the object is detected.

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

6.3 Setting unsuccessful

> The LED flashes quickly, 8 Hz.

> The sensor returns to the normal operating mode with unchanged values.

Possible causes

• Insufficient difference in measurements

• Max. programming time of 15 min. exceeded

6.4 Electronic lock

The unit can be locked electronically to prevent unauthorised setting. On delivery

the unit is not locked.

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED

status.

►To unlock repeat this step.

receiver

7 Operation

►Check whether the unit operates correctly.

> The green LED (transmitter) is lit when the sensor is ready for operation.

> The output is switched when the object is present. The yellow LED (receiver)

is lit.

8 Maintenance, repair, disposal

►Keep the lens of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic parts.

►After use dispose of the unit in an environmentally friendly way in accordance

with the applicable national regulations.

Faulty sensors must only be repaired by the manufacturer.

Technical data and further information at www.ifm.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de IFM

IFM

IFM OGH Manual de usuario

IFM

IFM OY4**S Series Manual de usuario

IFM

IFM SI 5000 Manual de usuario

IFM

IFM efector 200 O4H5 Series Manual de usuario

IFM

IFM O5H5 Series Manual de usuario

IFM

IFM OJ51 Series Manual de usuario

IFM

IFM OGE Manual de usuario

IFM

IFM PI22 Series Manual de usuario

IFM

IFM Efector 200 O6E4 Manual de usuario

IFM

IFM OGH3 Series Manual de usuario

IFM

IFM Efector 200 O4P5 Series Manual de usuario

IFM

IFM O5H5xA Series Manual de usuario

IFM

IFM OMH551 Manual de usuario

IFM

IFM SB1 Series Manual de usuario

IFM

IFM PK752 Series Manual de usuario

IFM

IFM Efector 200 OJ51 Series Manual de usuario

IFM

IFM O5P7 Series Manual de usuario

IFM

IFM Efector 100 GG712S Manual de usuario

IFM

IFM IFS Series Manual de usuario

IFM

IFM Efector 500 PY2068 Manual de usuario

IFM

IFM efector 200 OGS38 Series Manual de usuario

IFM

IFM Efector 200 OJ Manual de usuario

IFM

IFM O1D300 Manual de usuario

IFM

IFM LR3009 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario