IFM Electronic Efector200 OL Manual de usuario

Operating instructions

Diffuse reflection sensor

701271 / 04 12 / 2010

Contents

Function and features��3

Electrical connection��3

Montage��4

Commissioning��4

Setting of the sensitivity with stationary objects ��5

Setting of the sensitivity with moving objects ��6

Setting of the maximum sensitivity ��7

Programming the output function ��7

Operation��8

Maintenance��8

Function and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switched signal�

Range (r): see type label (value referred to white paper 200 mm x 200 mm)�

Electrical connection

►Isolate power, then connect the unit�

►Connect the unit as follows:

AC/DC Relais

Sensor with terminals Sensor with connector































Insert a miniature fuse according to the technical data sheet, if specified�

Core colours (for sensors with cable connection): BN = brown, BU = blue,

BK = black, WH = white�

Programming of the output function by push button (see page 7)�

The units with cable gland have a removable terminal block with screw terminals

(screws are at the base of the terminal block)�

After connection of the wires the terminal block must be reinserted�

Check the unit for reliable function after a short cirucit�

Montage

1: LEDs red, green, yellow

2: Pushbutton

3: LED yellow

Align the photocell and fasten it to a mounting bracket�

Maximum range is only possible with precise alignment�

Commissioning

The diffuse reflection sensor is supplied ready to operate (plug and play) set at the

max� sensing range� This is sufficient if the diffuse reflection sensor can operate

with maximum excess gain (highest contrast)�

The following setting procedures should only be necessary in less straightforward

applications, for example if a background must be „tuned out“�

Setting of the sensitivity with stationary objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

Setting with object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

Setting without object�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode��

You can also proceed in reverse order: first setting without the object, then with

the object�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

If the setting button is not activated for 15 minutes during the programming

process, the unit passes automatically into the operating mode with the sensitivity

being unchanged�

Setting of the sensitivity with moving objects

►Activate the programming mode of the unit without object�

►Press for about 2 s until the red LED flashes�

> The red LED goes out; the yellow and green LEDs flash alternately�

> The unit is in the programming mode�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s, then flash again alternately�

►During the measurement (approx� 1 s) allow at least two objects to move through

the sensing area of the lens�

►Press once�

> The yellow and green LEDs go out for approx� 1 s�

> After approx� 3 s the green LED is on�

> The unit is in the operating mode�

If the setting of the sensitivity is not possible (e�g� object signal and

background signal are about the same), the red LED flashes after step

3 for approx� 2 s� The unit then passes into the operating mode with the

sensitivity being unchanged�

Setting of the maximum sensitivity

• Go into the programming mode (step 1)�

• Align the unit so that no light is reflected�

• Press the setting button twice (see steps 2 and 3)�

Programming the output function

►Press for 10 s�

The red LED starts to flash fast after 2 s�

Then the yellow and green LEDs flash

alternately� After 8 s all LEDs go off,

the output function has changed from

light-on mode to dark-on mode (or vice

versa)�

Operation

Check the safe functioning of the sensor� Display by LEDs�

LED green lights Unit is ready for operation�

LED yellow lights Output is switched�

LED red lights Error in object detection, e�g� maladjustment,

soiling of the lenses�

LEDs yellow + red

Flash alternately, 2 Hz: output short-circuited�

Flash alternately, 1 Hz: internal malfunction,

(output is not switched)�

Maintenance

Keep the lens of the sensor free from soiling�

For cleaning do not use any solvents or cleaning agents which could damage the

plastic lenses�

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de IFM Electronic

IFM Electronic

IFM Electronic Efector 410 JN2100 Guía de aplicación

IFM Electronic

IFM Electronic PN5 series Manual de usuario

IFM Electronic

IFM Electronic SB 4 Series Manual de usuario

IFM Electronic

IFM Electronic GM705S Manual de usuario

IFM Electronic

IFM Electronic Efectror 200 OGE2 Series Manual de usuario

IFM Electronic

IFM Electronic efector150 Manual de usuario

IFM Electronic

IFM Electronic efector 200 OPU200 Manual de usuario

IFM Electronic

IFM Electronic efector100 ID503A Manual de usuario

IFM Electronic

IFM Electronic efector200 OJ51 Series Manual de usuario

IFM Electronic

IFM Electronic Efector 200 OL Series Manual de usuario

IFM Electronic

IFM Electronic LR8300 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic SM6000 Manual de usuario

IFM Electronic

IFM Electronic TUV NORD Efector 110 GM701S Manual de usuario

IFM Electronic

IFM Electronic efector 200 OJ Series Manual de usuario

IFM Electronic

IFM Electronic efector 300 SM7001 Manual de usuario

IFM Electronic

IFM Electronic O3M151 Manual del propietario

IFM Electronic

IFM Electronic Efector200 OG Manual de usuario

IFM Electronic

IFM Electronic efector200 OC Manual de usuario

IFM Electronic

IFM Electronic VSA003 Manual de usuario

IFM Electronic

IFM Electronic GM701S Manual de usuario

IFM Electronic

IFM Electronic EFECTOR 500 PI26 Manual de usuario

IFM Electronic

IFM Electronic LR2750 Manual de usuario

IFM Electronic

IFM Electronic efector200 OT Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario

IFM Electronic efector200 OL Manual de usuario

Manuales populares de Accesorios de otras marcas