IFM Electronic Efector150 Manual de usuario

Operating instructions

(Ex protection related part) for capacitive sensors

according to EU directive 94/9/EC annex VIII (ATEX)

group II, equipment category 3D

KI5**A / KI0**A

706246 / 00 10 / 2012

UK

2

Remarks for safe use in hazardous areas

Functions and features

• Use in hazardous areas according to the classification

II 3D

(group II, category 3D, apparatus for dust atmosphere).

Complies with the requirements of the standards EN 60079-0 and EN 60079-31.

• Marking

II 3D Ex tc IIIC T90°C Dc X IP65/67

• Permissible operating temperature of the application (proper usage):

Ta: -20°C...+60°C

Installation / Set-up

The units must only be installed, connected and set up by qualified staff. The qualified staff

must have knowledge of protection classes, regulations and provisions for apparatus in

hazardous areas.

Check whether the classification (see "Marking" above and marking on the unit) is suitable

for the application.

Installation remarks / Installation

• Adhere to the relevant national regulations and provisions.

• The relevant installation regulations must be adhered to. In particular, take into account the

requirements relating to the temperature limitation as regards the expected dust deposits.

• Avoid electrostatic charging on housings and cables.

• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential

of metal parts (plug housing, fixing elements, etc.).

• Protect the units and the cables efficiently against damage.

• To avoid soiling, do not remove the dust caps from the cable glands or the plugs until

introducing the cables or attaching the socket.

• After the electrical connection has been made fully insert the terminal chamber onto

the sensor and tighten the nut onto the terminal chamber using a spanner (a/f 36 mm)

(tightening torque min. 10 Nm).

• Maintenance intervals are application-specific and therefore need to be defined by the

operator depending on the operating conditions.

• During maintenance, especially those parts on which the type of protection depends need

to be examined (e.g. integrity of the components of the cable gland, of the seals).

3

UK

Special conditions for safe operation

• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must

be ensured or the cable must be firmly laid.

• Do not disconnect the cables from units with terminal chamber while live.

• The housing and housing parts made of plastic were tested in accordance with

EN 60079-0 for group II and for a low mechanical risk with an impact energy of 4 joules.

• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected

place.

• Where units require an additional fuse, this must be located outside the hazardous areas.

Maintenance / repair

The unit must not be modified nor can it be repaired. In case of a fault please contact the

manufacturer.

Data sheets, EC declaration of conformity and EC type test certificates are available from

the manufacturer on request.

Otros manuales para efector150

3

Tabla de contenidos

Otros manuales de Accesorios de IFM Electronic

IFM Electronic

IFM Electronic SB 4 Series Manual de usuario

IFM Electronic

IFM Electronic Efectror 200 OGE2 Series Manual de usuario

IFM Electronic

IFM Electronic efector150 Manual de usuario

IFM Electronic

IFM Electronic efector 200 OW Series Manual de usuario

IFM Electronic

IFM Electronic LR2750 Manual de usuario

IFM Electronic

IFM Electronic O1D108 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 O5H Manual de usuario

IFM Electronic

IFM Electronic ecomat100 CR2101 Guía de aplicación

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

IFM Electronic

IFM Electronic O3M151 Manual del propietario

IFM Electronic

IFM Electronic Efector 200 O6T3 Series Manual de usuario

IFM Electronic

IFM Electronic Efector 200 OL Series Manual de usuario

IFM Electronic

IFM Electronic Efector200 OGS50 Series Manual de usuario

IFM Electronic

IFM Electronic VNB001 Manual de usuario

IFM Electronic

IFM Electronic efector 300 SU8200 Manual de usuario

IFM Electronic

IFM Electronic efector300 SBU3 Manual de usuario

IFM Electronic

IFM Electronic O5D10 series Manual de usuario

IFM Electronic

IFM Electronic efector180 IX5010 Manual de usuario

IFM Electronic

IFM Electronic efector 250 Manual de usuario

IFM Electronic

IFM Electronic O5E5 A Series Manual de usuario

IFM Electronic

IFM Electronic efector500 PQ08 Series Manual de usuario

IFM Electronic

IFM Electronic Efector 500 PL2058 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic Efector 200 OJ5192 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario