IFM Electronic Efector 300 Manual de usuario

Amendment to the operating instructions:

Selection of the operating mode via

IO-Link interface

SAxxxx

706416 / 00 03 / 2016

1 Preliminary note

Please read the supplied operating instructions for all articles described

below prior to set-up.

These instructions are an amendment to the supplied operating instructions of the

SAxxxx flow sensors in which all setting options via the pushbuttons on the sensor

are described.

These present instructions also give alternative options for parameter setting via

the IO-Link interface.

2 Operating modes

With regard to the software the SAxxxx flow sensor behaves like 3 sensors on a

hardware platform: The following three operating modes can be selected for flow

measurement.

Operating

mode

Medium Process value display

REL Liquids, air % of the taught range

LIQU Liquids m/s, l/min, m

/h (fps, gpm, cfm)

GAS Air m/s, l/min, m

/h (fps, gpm, cfm)

The operating modes can be set via the pushbuttons on the sensor. Alternatively,

the operating mode can be transferred to the sensor by means of the memory

plug E30398 (→3) or the LINERECORDER SENSOR software (→4).

3 Operating mode selection via memory plug E30398

By means of the memory plug E30398 it is possible to duplicate the parameter set

and therefore the operating mode of a sensor to several sensors of the same type.

Detailed function description

→Operating instructions E30398 at www.ifm.com.

3.1 Procedure

1. Set the operating mode on the sensor:

►Change from the RUN mode to the initialisation menu [

INI

]

►Select [ModE] and define the operating mode: REL, GAS, LIQU.

A medium and an internal pipe diameter must be entered for the operating modes

LIQU and GAS.

When the factory setting is changed (ModE = REL), the unit displays [≡≡≡≡] to force

these entries:

►Press [●].

> [MEdI] is displayed.

►Define medium.

> [diA] is displayed.

►Define the internal pipe diameter in mm or inch.

The operating mode REL requires a flow adjustment.

A change of the operating mode leads to a restart of the unit.

The settings are saved in the respective operating mode,

i.e. after a change of the operating mode the settings are not lost.

2. Save the parameter set of the sensor on the memory plug:

Requirement:

The memory plug is used as delivered (empty / [Write protect-

ed])

►Connect the memory plug to the supply voltage.

►Connect memory plug and sensor.

> The memory plug reads the parameter set of the sensor

and saves it.

Ub P

Reading process

Process terminated.

Memory plug full / [Write

protected].

3. Transfer parameter set to other sensors:

►Connect the memory plug to the supply voltage.

►Connect the memory plug with a sensor of the same type.

> The memory plug writes its parameter set to the sensor.

Writing process

Process terminated

►Repeat the process with sensors of the same type as often as you wish.

Ub P

4 Operating mode selection via LINERECORDER

SENSOR

4.1 System requirements

4.1.1 LINERECORDER SENSOR

Required version: 4.1.0.43.

Detailed function description

→Operating instructions QA0001 at www.ifm.com.

4.1.2 IO-Link interface E30390

Required version: from firmware 2.1.5 – 1.2.5

(production after 17/02/2016, see label on the unit).

The latest firmware is available for download at www.ifm.com.

►Download firmware and overwrite firmware on the IO-Link interface.

Detailed function description

→Operating instructions E30390 at www.ifm.com.

4.1.3 IODD (IO Device Description) for SAxxxx flow sensors

There is a separate IODD for each operating mode which is available for down-

load via ifm's homepage:

For ifm units a number of IODDs is stored in the LINERECORDER SENSOR

software. If the required IODD is missing, it can be downloaded via the symbol

marked in the LINERECORDER SENSOR:

(If the symbol is pink, new IODD files are available for download.)

4.2 Procedure

Example: SA5000 flow sensor.

1. ►Connect sensor to PC via IO-Link interface and read parameter settings

via the LINERECORDER SENSOR.

Possible error message:

►Update firmware (→4.1.2).

The parameter for the operating mode [ModE] is displayed but cannot

be changed.

The factory setting for SAxxxx is the operating mode [ModE] = REL.

2. ►Change to the offline mode.

3. ►Select IODD for the required operating mode.

Each of the three operating modes has its own IODD:

- SAxxxx (operating mode REL for flow measurement in liquids and air)

- SAxxx_GAS (operating mode GAS for flow measurement in air)

- SAxxx_LIQU (operating mode LIQU for flow measurement in liquids)

If the required IODD is not available in the unit catalogue, it has to be

downloaded in the online mode (→4.1.3).

4. ►Change parameter settings of the sensor.

5. ►Save changed parameter set as lrp file.

6. ►Change to the online mode.

In the offline mode, reading or writing to a connected device is not

possible. The saved file with the parameter set can only be accessed

in the online mode and then be written to the device.

7. ►Load parameter set as file.

►Open the lrp file stored in step 5.

The lrp file contains the operating mode selected in step 3 with the

parameter settings adapted in step 4.

8. ►Write the parameter set to the sensor

> The sensor carries out a reset and restarts:

> The sensor is now in the GAS operating mode:

In case of a new parameter setting via the LINERECORDER SENSOR the

software detects the newly set operating mode automatically.

Otros manuales para Efector 300

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de IFM Electronic

IFM Electronic

IFM Electronic SB 4 Series Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic efector200 OGT3 Series Manual de usuario

IFM Electronic

IFM Electronic Efector 200 Manual de usuario

IFM Electronic

IFM Electronic efector200 OC Manual de usuario

IFM Electronic

IFM Electronic efector200 OT Manual de usuario

IFM Electronic

IFM Electronic SM7000 Manual de usuario

IFM Electronic

IFM Electronic LK7 Manual de usuario

IFM Electronic

IFM Electronic efector 200 OJ Series Manual de usuario

IFM Electronic

IFM Electronic efector 300 SU7000 Manual de usuario

IFM Electronic

IFM Electronic Efector 100 Manual de usuario

IFM Electronic

IFM Electronic Efector 500 PL2058 Manual de usuario

IFM Electronic

IFM Electronic LK1022 Manual de usuario

IFM Electronic

IFM Electronic efector300 SBU3 Manual de usuario

IFM Electronic

IFM Electronic Efector 150 KG5070 Manual de usuario

IFM Electronic

IFM Electronic PN72 Series Manual de usuario

IFM Electronic

IFM Electronic efector200 OT Series Manual de usuario

IFM Electronic

IFM Electronic VKV021 Manual de usuario

IFM Electronic

IFM Electronic efector 160 LR8300 Manual de usuario

IFM Electronic

IFM Electronic efector 300 SU8000 Manual de usuario

IFM Electronic

IFM Electronic O5D10 series Manual de usuario

IFM Electronic

IFM Electronic Efector 300 Manual de usuario

IFM Electronic

IFM Electronic efector200 OL Manual de usuario

IFM Electronic

IFM Electronic O1D108 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario