HPE LSQM2MPUD0 Manual de usuario
Manual version: 6PW108-20180130 BOM: 3123A0XN
i
LSQM2MPUD0 management and route unit
1 Card identifier
The card identifier LSQM2MPUD0 is in the upper right corner of the front panel.
2 Specifications
IMPORTANT:
•The S7506E (non-PoE) does not support this card.
•Before installing the card, you must remove the protection cover from the card to ensure correct
installation.
•The 40G QSFP+ fiber module cannot be connected to a 10-Gbps SFP+ transceiver module
when the 40G QSFP+ fiber module is installed in this card.
Table 1 LSQM2MPUD0 specifications
Item Specifications
Flash 1 GB
SDRAM (DDR3) 4 GB
Card size (H × W × D) 40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in)
Power consumption 55 W to 96 W
Ports
•1 x console port
•1 x USB console port
•4 x network management ports: 2 × 10/100/1000BASE-T copper
ports and 2 SFP fiber ports
•2 x QSFP+ ports
•1 x USB port
Port speed
•Console port: ≤115200 bps (default: 9600 bps)
•USB console port: ≤115200 bps (default: 9600 bps)
•10/100/1000BASE-T copper port: 10/100/1000 Mbps, half/full
duplex
•SFP fiber port: 1000 Mbps
•QSFP+ fiber port: 40 Gbps
Transmission medium and max
transmission distance
•Console port: 15 m (49.21 ft) over ordinary asynchronous serial
port cables
•USB console port: 10 m (32.81 ft) over USB-AB cables
•10/100/1000BASE-T copper port: 100 m (328.1 ft) over Category
5 or higher twisted pair cables
•SFP fiber port: see Table 3
•QSFP+ fiber port: see Table 4, and Table 5
Compatible device models S7503E/S7506E/S7506E-V/S7510E
Applicable host software versions Version 7168 and later
Manual version: 6PW108-20180130 BOM: 3123A0XN
ii
NOTE:
•To successfully connect an Ethernet port to a network management port (SFP port) on the card,
make sure the Ethernet port is operating in full duplex mode and at the port speed of 1000 Mbps.
•H3C recommends not using a USB extender cable to connect the USB port.
The 10/100/1000BASE-T copper port uses an RJ-45 connector.
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
Pin 10BASE-T/100BASE-TX/1000BASE-T
Signal Function
1 MX_0+ Transmits and receives data.
2 MX_0- Transmits and receives data.
3 MX_1+ Transmits and receives data.
4 MX_2+ Transmits and receives data.
5 MX_2- Transmits and receives data.
6 MX_1- Transmits and receives data.
7 MX_3+ Transmits and receives data.
8 MX_3- Transmits and receives data.
Table 3 descirbes the SFP transceiver modules available for the SFP ports on the card.
Table 3 SFP transceiver module specifications
Module Central
wavelength Connector
type Cable
specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A
850 nm LC 50/125 µm multi-mode
optical fiber (MMF) 550 m (0.34 miles)
850 nm LC 62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-SX-MM850-D
850 nm LC 50/125 µm MMF 550 m (0.34 miles)
850 nm LC 62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-LX-SM1310-A
1310 nm LC 9/125 µm single-mode
optical fiber (SMF) 10 km (6.21 miles)
1310 nm LC 50/125 µm MMF 550 m (1804.46 ft)
1310 nm LC 62.5/125 µm MMF 550 m (1804.46 ft)
PIN #8
PIN #1
Manual version: 6PW108-20180130 BOM: 3123A0XN
iii
Module Central
wavelength Connector
type Cable
specifications
Maximum
transmission
distance
SFP-GE-LX-SM1310-D
1310 nm LC 9/125 µm SMF 10 km (6.21 miles)
1310 nm LC 50/125 µm MMF 550 m (1804.46 ft)
1310 nm LC 62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LH40-SM1310 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1310-D 1310nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 nm LC 9/125 µm SMF 70 km (43.50 miles)
SFP-GE-LH80-SM1550-D 1550nm LC 9/125 µm SMF 70 km (43.50 miles)
SFP-GE-LH100-SM1550 1550 nm LC 9/125 µm SMF 100 km (62.14 miles)
SFP-GE-LX-SM1310-BIDI RX: 1490 nm
TX: 1310 nm LC 9/125 µm SMF 10 km (6.21 miles)
SFP-GE-LX-SM1490-BIDI RX: 1310 nm
TX: 1490 nm LC 9/125 µm SMF 10 km (6.21 miles)
NOTE:
•BIDI modules use different central wavelengths in transmit and receive directions, in order to
implement bidirectional transmission of optical signals over the same fiber.
•The BIDI modules must be used in pairs. For example, if you install the
SFP-GE-LX-SM1310-BIDI in the local port, you must install the SFP-GE-LX-SM1490-BIDI in the
peer port.
Table 4 describes the QSFP+ transceiver modules available for the QSFP+ ports on the card.
Table 4 QSFP+ transceiver module specifications
Module Central
wavelength Connector Fiber
specifications
Maximum
transmission
distance
QSFP-40G-SR4-MM850
850 nm MPO 50/125 µm MMF 100 m (328.08 ft)
850 nm MPO 50/125 µm MMF 150 m (492.13 ft)
QSFP-40G-SR4-MM850-N
DDM
850 nm MPO 50/125 µm MMF 100 m (328.08 ft)
850 nm MPO 50/125 µm MMF 150 m (492.13 ft)
QSFP-40G-CSR4-MM850
850 nm MPO 50/125 µm MMF 300 m (984.25 ft)
850 nm MPO 50/125 µm MMF 400 m (492.13 ft)
QSFP-40G-CSR4-MM850-
NDDM
850 nm MPO 50/125 µm MMF 300 m (984.25 ft)
850 nm MPO 50/125 µm MMF 400 m (492.13 ft)
QSFP-40G-BIDI-SR-MM850 850 nm LC 50/125 µm MMF
100 m (328.08 ft)
150 m (492.13 ft)
Manual version: 6PW108-20180130 BOM: 3123A0XN
iv
Module Central
wavelength Connector Fiber
specifications
Maximum
transmission
distance
QSFP-40G-LR4-WDM1300
1271 nm
1291 nm
1311 nm
1331 nm
LC 9/125 µm SMF 10 km (6.21 miles)
QSFP-40G-LR4L-WDM1300
1271 nm
1291 nm
1311 nm
1331 nm
LC 9/125 µm SMF 2 km (1.24 miles)
QSFP-40G-ER4-WDM1300
1271 nm
1291 nm
1311 nm
1331 nm
LC
9/125 µm
single-mode optical
fiber
40 km (24.86 miles)
NOTE:
•The QSFP-40G-LR4-WDM1300 cannot be connected to the 10-Gbps SFP+ module.
•The QSFP-40G-LR4L-WDM1300 is supported only if the software version of the device is
Release 7536P07 or later.
Table 5 describes the QSFP+ cables that used for connecting 40G QSFP+ ports.
Table 5 QSFP+ cable specifications
QSFP+ cable Cable length Data rate Cable type
LSWM1QSTK0 1 m (3.28 ft) 40 Gbps QSFP+ cable
LSWM1QSTK1 3 m (9.84 ft) 40 Gbps QSFP+ cable
LSWM1QSTK2 5 m (16.40 ft) 40 Gbps QSFP+ cable
Table 6 describes the specifications of the QSFP+ fiber cables that used for connecting 40G QSFP+
ports.
Table 6 QSFP+ fiber cables available for the QSFP+ ports
QSFP+ fiber cable Cable length Data rate Remarks
QSFP-40G-D-AOC-7M 7 m (22.97 ft)
40 Gbps For connecting 40G QSFP+
ports
QSFP-40G-D-AOC-10M 10 m (32.81 ft)
QSFP-40G-D-AOC-20M 20 m (65.62 ft)
3 Related documentation
For module installation, see H3C S7500E Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2014-2018 New H3C Technologies Co ., Ltd.
The information in this document is subject to change without notice.
Otros manuales de Cambiar de HPE
HPE
HPE FlexNetwork 5510 HI Series Manual de usuario
HPE
HPE OfficeConnect 1920S Series Manual de usuario
HPE
HPE FlexNetwork 5510 HI Series Manual de usuario
HPE
HPE 5820X Series Manual de usuario
HPE
HPE FlexNetwork 7500 Series Manual de instalación
HPE
HPE 5820X Series Manual de usuario
HPE
HPE FlexFabric 7900 Series Manual de usuario
HPE
HPE FlexFabric 5950 Series Manual de usuario
HPE
HPE StoreFabric M-Series Instrucciones de uso
HPE
HPE OfficeConnect 1910 Series Guía de seguridad
HPE
HPE 5140 24G PoE+ 4SFP+ EI Sw Instrucciones de montaje
HPE
HPE FlexFabric 5800 Series Manual de usuario
HPE
HPE Altoline 6822 48XG 6QSFP28 x86 ONIE Instrucciones de montaje
HPE
HPE FlexNetwork 10500 SERIES Manual de instalación
HPE
HPE FlexNetwork 5510 HI Series Manual de usuario
HPE
HPE OfficeConnect 1950 12XGT 4SFP+ Manual de usuario
HPE
HPE FlexFabric 5940 SERIES Manual de usuario
HPE
HPE Aruba 6300M Instrucciones de montaje
HPE
HPE FlexNetwork 10500 SERIES Manual de usuario
HPE
HPE 6Gb SAS BL Manual de usuario
