HPE FlexNetwork NJ5000 5G PoE Plus Walljack Manual de usuario
1
HPE FlexNetwork NJ5000 5G PoE+
Walljack Switch(JH237A)
Quick Start Guide
The information in this document is subject to change without notice.
© Copyright 2016 Hewlett Packard Enterprise Development LP
Part number: 5998-7330R
Version:6PW102-20161009
Hewlett Packard Enterprise 3000 Hanover Street Palo Alto, CA 94304
5998-7330R
2
This quick start guide shows you how to install and get started with the HPE
FlexNetwork NJ5000 5G PoE+ Walljack Switch (RMN HNGZA-HA0025, the
Regulatory Model Number) JH237A, hereafter referred to as the switch.
▌Overview
Figure 1 shows the front, back, and bottom views of the switch.
Figure 1 Switch views
Package contents
The product package includes the following items:
•HPE NJ5000 5G PoE+ switch.
•A mounting bracket.
•An Ethernet network cable.
3
•A pair of mounting screws (3.5 × 25) for sides (for EU) and a pair of mounting
screws (3.5 × 12) for top and bottom (for US).
•Two secure screws: one Phillips head screw and one security-head Torx-10
screw.
•Documentation.
Ports
•Four Gigabit Ethernet LAN ports (bottom of unit)—Auto-sensing 1000BASE-T
Ethernet ports with RJ-45 connectors. Two ports can provide IEEE 802.3af or
802.3at power over Ethernet (PoE) to supply power to PoE Powered Devices
(PDs).
•One Gigabit Ethernet uplink port (back of unit)—Auto-sensing 1000BASE-T
Ethernet port with an RJ-45 connector.
•One console port (back of unit).
Reset button
The reset button is accessible through a hole on the side panel of the switch.
To reboot the switch:
1. Insert a pin or paper clip into the reset button hole.
2. Press and hold the button for 1 to 5 seconds.
3. Release the button.
To change the operation mode for the switch:
1. Insert a pin or paper clip into the reset button hole.
2. Press and hold the button for 7 to 12 seconds until the management mode LED
flashes (10 times per second).
3. Release the button. The management mode LED enters the target mode. If the
LED is on, the switch operates in managed mode. If the LED is off, the switch
operates in unmanaged mode.
To reset the switch to factory defaults:
1. Insert a pin or paper clip into the reset button hole.
2. Press and hold the button for more than 15 seconds until the status LEDs (Power
and Uplink) flash.
3. Release the button.
LEDs
Figure 2 shows the status LEDs on the switch.
4
Figure 2 LED view
Table 1 LED status descriptions
LED Status Description
Power status LED
Steady green The switch is powered by 802.3at PoE+ and
the power supply is operating correctly.
Flashing green The switch is powered on and is performing
a self-test.
Slow flashing
green
The switch is powered by 802.3af PoE and
the power supply is operating correctly.
Off The switch is not powered on or the power
supply is faulty.
Steady red A failure has occurred.
LAN port LED
Steady green A link is present.
Flashing green The port is receiving or sending data.
Off No link is present.
5
LED Status Description
PoE output port
LED
Steady green A link is present (no PoE).
Steady amber A link is present (PoE).
Flashing green The port is sending or receiving data (no
PoE).
Flashing amber The port is sending or receiving data (PoE).
Slow flashing
amber The PoE power supply is faulty.
Off No link is present.
Uplink port LED
Steady green A link is present.
Flashing green The port is sending or receiving data.
Off No Link is present.
Management
mode LED
On The switch is operating in managed mode.
Off The switch is operating in unmanaged
mode.
▌Installing the switch
The switch is designed to be mounted on a standard NEMA-WD6 (US) or BS 4662
(International) in-wall electrical outlet box.
You can also install the switch by using the optional HPE unified wired-WLAN
walljack table/flush wall mount kit (JL022A). This kit, which is purchased separately,
lets you install the switch on a horizontal surface or wall.
Restrictions and guidelines
This equipment must be installed in compliance with local and national building
codes, regulatory restrictions, and FCC rules. For the safety of people and equipment,
only professional network personnel should install the device.
To avoid possible bodily injury or equipment damage, read the following safety
recommendations before you install the switch. The recommendations do not cover
every possible hazardous condition.
•Install with six inches or more of clearance around the device.
•Keep the device clean and dust-free.
•Make sure the ground is dry and flat and anti-slip measures are in place.
•Do not place the device in a moist area and avoid liquid surrounding the device.
6
•Keep the device and installation tools away from walkways.
Installing the switch over an electrical outlet box
1. Place the mounting bracket, with the UP arrow pointing up, on the electrical outlet
box, and then use two of the supplied mounting screws to secure the bracket to
the box.
The two long mounting screws are for an EU electrical outlet box. The two short
mounting screws are for a US electrical outlet box.
Figure 3 Securing the mounting bracket to an electrical outlet box (EU)
7
Figure 4 Securing the mounting bracket to an electrical outlet box (US)
2. Connect the network cable from the electrical outlet box to the RJ-45 uplink port
on the back of the switch.
Figure 5 Connecting the network cable
8
3. Align the installation hole in the rear of the switch with the standout on the
mounting bracket.
Figure 6 Aligning the installation hole
4. Push the switch onto the mounting bracket, and then slide it down until it is fully
engaged. Then secure the switch to the bracket by using the Phillips-head screw
or security-head security Torx-10 screw. Do not release the switch until you
confirm that it is secured in place.
9
Figure 7 Securing the switch
Other mounting options using optional Mounting Kit
Additional mounting configurations are possible by using the JL022A HPE Unified
Wired-WLAN Walljack Table/Flush Wall Mount Kit. Please contact your Hewlett
Packard Enterprise sales representative to purchase this part. Detailed mounting
instructions are provided with the kit.
10
Figure 8 Securing the switch
Using the kit, one can attach the switch to a wall without an electrical junction box.
The optional mounting kit is installed first. Then the mounting bracket attaches to the
mounting kit. Finally, the unit attaches to the mounting bracket as previously
described.
Note: Before installing the switch on a wall, make sure the surface of the wall can
support a minimum weight of 0.9 kg (2 lbs) and the weight of the extra cables.
Using the kit, one can install the switch unit on a desktop. The optional mounting kit is
installed first on a flat surface. Then the mounting bracket attaches to the mounting
kit. Finally, the unit attaches to the mounting bracket as previously described.
▌Powering the Switch
The switch can be powered by a PoE-enabled switch or by a compatible PoE Power
Injector.
1
2
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cambiar de HPE
HPE
HPE FlexFabric 5940 SERIES Manual de usuario
HPE
HPE OfficeConnect 1950 Series Manual de usuario
HPE
HPE 5800 Series Manual de usuario
HPE
HPE Aruba 3810 Manual de usuario
HPE
HPE LSWM1FANSC Manual de usuario
HPE
HPE 5820X Series Manual de usuario
HPE
HPE FlexNetwork 5130 EISeries Manual de usuario
HPE
HPE StoreFabric M-Series Instrucciones de uso
HPE
HPE FlexNetwork 7500 Switch Manual de usuario
HPE
HPE Aruba Instant On 1960 24G 20p Class4 4p Class6 PoE 2XGT 2SFP+ 370W... Instrucciones de montaje
HPE
HPE Aruba 6300M Instrucciones de montaje
HPE
HPE FlexFabric 5930 Series Manual de instalación
HPE
HPE FlexFabric 12900E Manual de usuario
HPE
HPE JL324A Instrucciones de montaje
HPE
HPE OfficeConnect 1950 12XGT 4SFP+ Manual de usuario
HPE
HPE Aruba 3810M Instrucciones de montaje
HPE
HPE FlexNetwork 10500 SERIES Manual de usuario
HPE
HPE OfficeConnect 1920S8G series Manual de usuario
HPE
HPE FlexFabric 7900 Series Manual de usuario
HPE
HPE Aruba Instant On 1960 Instrucciones de montaje
