HP 705 Guía de inicio rápido

For Series 700 systems operating with HP-UX releases 9.01, 9.03, and 9.05, you

must load patch PHCO_5881 for disktab and sam functionality, and patch

PHSS_5776 for network installation functionality.

For Series 300 systems, this disk drive is supported on the following releases by

loading the appropriate patch:

HP–UX 9.03: PHCO_6819

HP–UX 9.10: PHCO_6819

Pascal: Rev.

3.25C (Quantum only

, not needed for Seagate)

Basic: Rev. 6.3; SCSI Binary Rev. 6.7

For

Series 400 systems, this disk drive is supported at HP-UX release 9.03 and 9.10,

with patch PHCO_6819 required for full functionality of newfs and sam.

The software patches may be obtained from HP Customer Service.

To install the patches to HP–UX, perform the following steps:

1. Begin the HP-UX software installation process. If the system has a one of the

drives installed, the following message appears:

“Note:

the destination disk type “

disk–drive

”

was not found in the disk table /etc/disktab.

(Press any key to continue.)”

2. Press any key. The screen displays the following message: “If

model

number:

“

disk–drive

”, is incorrect, and

a correct one

(one

that has an entry in the /etc/disktab) is known,

please

enter it now otherwise press return.”

3. a. For Series 300 and 400, type: Return

The

screen now displays disk physical parameters. Change three of these

param

eters as shown, leaving the other parameters at the default values:

1024 byte sectors per track: [

]

Tracks per cylinder: [

]

RPMs of the disk: [

5400

]

b. For Series 700, type: MICROP_2112 Return

The MICROP_2112 drive is functionally equivalent to the new drives. By

using this entry, you can complete the software installation process.

4. Let the software installation process complete.

5. Install the appropriate patch using /etc/update and reboot the system.

1–GB Disk Drive

User Notes

Refer to your workstation owner’s guide or your disk drive installation

guide for detailed information about installing your disk drive. During

the installation procedure, you may have to change the SCSI ID of your

disk drive. Refer to the appropriate illustration to set the SCSI ID

jumpers to the desired SCSI ID.

NOTICE: We recommend that you use SCSI ID 6 for your

workstation’s first hard disk drive, and SCSI ID

5 for the second hard disk drive.

  

The 1–GB disk drive is fully operational with HP-UX Release 9.01 and

later on Series 700 systems (releases 9.01, 9.03, and 9.05 require patches

to the operating system). On Series 300 and 400 systems, this disk drive

is supported only at HP-UX release 9.03 and 9.10, and a patch is re-

quired to obtain full functionality. Please see the patch instructions on

the last page of this document.

Also, for Series 700 systems, the following patches are necessary to run

diagnostics:

HP-UX 9.01 -Diagnostic support is not available for these

drives running on HP–UX 9.01

HP-UX 9.03 through 9.07 – PHSS_6620

HP-UX 10.01 – PHSS_6607

HP-UX 10.10 – PHSS_6796

The HP part numbers for these drives are A1658–60007 (spare) and

A1658–69007 (exchange).

Part Number A1658–90690

Edition E0696

Printed in U.S.A.



CAUTION

NOT

plugs for J2 on J6.

ou will damage the

internal contacts

use the jumper

SCSI

erm Power

from Drive

Seagate ST31051N Disk Drive Jumpers

SCSI

FRONT

Quantum 1050S Disk Drive Jumpers

Otros manuales para 705

Este manual sirve para los siguientes modelos

Otros manuales de Almacenamiento de HP

HP StorageWorks NAS b2000 - v2 Manual de funcionamiento

HP Compaq Presario,Presario 4400 Guía

HP Surestore Tape Library Model 10/180 Manual de usuario

HP StoreOnce B6000 Instrucciones de funcionamiento

HP Surestore 64 - Director Switch Manual de usuario

HP StorageWorks 300 - Virtual Library System EVA... Manual de usuario

HP D2D Manual de usuario

HP StorageWorks DLT80 Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP StorageWorks 7100 - Virtual Array Manual de usuario

HP StorageWorks 7110 - Virtual Array Manual de usuario

HP StorageWorks 8B - FC Entry Switch Manual de usuario

HP VS80 - StorageWorks DLT VS 80 Tape Drive Manual de usuario

HP SCSI Ultra320 Guía de instalación

HP D2D Manual de usuario

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Manual

HP MSA 30 Manual de usuario

HP Surestore Disk Array 12h - And FC60 Manual de operación y mantenimiento

HP 418371-B21 - Dual Port 72 GB Hard Drive Manual de usuario

HP StorageWorks 500 Generation 2 Manual

HP 157770-001 - DAT Drive 20/40 Tape Manual de instrucciones

HP Open View Manual del producto

HP StoreOnce D2D Backup System Gen2E Manual

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario