HP Xw4400 - Workstation - 2 GB RAM Manual de usuario
CRU Dataport DX115 kit installation
Introduction
This document describes how to install the CRU Dataport DX115® removable media kit in your
workstation. The DX115 kit enables you to install removable media in your workstation.
Kit contents
Ensure that the following components are included in your drive kit:
●Warranty
●DX115 unit (case and drive carrier)
●Installation document
●SATA or SAS cable
●Five M3 screws
●Five 6-32 screw
●Tape label
© 2008 Hewlett-Packard Development Company, L.P. The HP Invent logo is a
registered trademark of Hewlett-Packard Development Company, L.P. Microsoft and
Windows are U.S. registered trademarks of Microsoft Corporation. Printed in the U.S.
ENWW Introduction 1
Warnings and cautions
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce
the risk of injury from a hot component, enable the surface to cool before touching.
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed
area marked with this symbol.
WARNING! To reduce the risk of electric shock or damage to your equipment:
— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
workstation setup, posture, health, and work habits for computer users, and provides important electrical
and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the
documentation CD (if one is included with the product).
WARNING! If a product is shipped in packaging marked with this symbol, , the product must always
be lifted by two persons to avoid personal injury due to product weight.
CAUTION: Static electricity can damage the electronic components of the workstation. Before
beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal
object.
CAUTION: Observe the following cautions when removing or replacing a processor:
— Installing a processor incorrectly can damage the system board. Contact an HP authorized reseller
or service provider to install the processor. If you plan to install the processor yourself, read all of the
instructions carefully before you begin.
— Failure to follow the workstation preparation instructions can result in an improperly installed
processor, causing extensive workstation damage.
— Processor socket pins are delicate and bend easily. Use extreme care when placing the processor
in the socket.
2 CRU Dataport DX115 kit installation ENWW
CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge
(ESD) precautions while performing the system parts removal and replacement procedures:
— Work on a static-free mat.
— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body
to the ground.
— Create a common ground for the equipment you are working on by connecting the static-free mat,
static strap, and peripheral units to that piece of equipment.
NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested
for reliability and are manufactured to high quality standards.
ENWW Warnings and cautions 3
Step 1—Preparing the workstation
To prepare the workstation:
1. Refer to your workstation documentation for instructions on disassembling and preparing the
workstation for installation. Follow the instructions for shutting down power and disconnecting all
power from the system.
2. Remove the access panel and front bezel of your workstation. If necessary, refer to the Service
and Technical Reference Guide for your HP Workstation at http://www.hp.com/support/
workstation_manuals.
Step 2—Installing the DX115 case into the optical drive bay
Refer to the steps for your workstation in the following sections.
CAUTION: Insert or remove the carrier (with a disk drive) only when the workstation is shut down.
Other procedures may result in system hangs, data loss or even drive damage. (The component
supplier’s user guide describes a procedure for inserting or removing the carrier (with drive) while the
workstation is booted and then powering the drive via the enclosure’s power switch. Microsoft Windows
XP and Vista do not support this action.)
HP xw6000 Workstation series
1. Remove and discard the counter-sunk screw at the side of the DX115 case as shown (for xw6000
series only). This hole will be used for the shipping screw.
2. Install the DX115 unit in the optical drive bay using the quick release system.
4 CRU Dataport DX115 kit installation ENWW
3. Install one 6-32 x 1/4 in. screw (silver) per DX115 unit for shipping support as shown.
CAUTION: Failure to install the shipping screw may result in damage to the removable hard drive
system.
HP xw4000 Workstation series
1. Install four, M3 x 5mm screws (black) in the lower four mounting holes.
2. Install the DX115 unit in the optical drive bay using the quick release system.
3. Install one, M3 x 5mm screw (black) per DX115 unit for shipping support as shown.
ENWW Step 2—Installing the DX115 case into the optical drive bay 5
HP xw8000 and xw9000 Workstation series
1. Install the DX115 unit in the optical drive bay using the quick release system
2. Install one M3 x 5mm screw (black) per DX115 unit for shipping support as shown.
CAUTION: Failure to install the shipping screw may result in damage to the removable hard drive
system.
Step 3—Installing a hard disk in the DX115 carrier
CAUTION: Insert or remove the carrier (with a disk drive) only when the workstation is shut down.
Other procedures may result in system hangs, data loss or even drive damage. (The component
supplier’s user guide describes a procedure for inserting or removing the carrier (with drive) while the
workstation is booted and then powering the drive via the enclosure’s power switch. Microsoft Windows
XP and Vista do not support this action.)
NOTE: It is not necessary to remove the DX115 case from the workstation for this step.
Install your hard drive in the DX115 carrier. For detailed instructions, refer to either:
●The CRU Dataport DX115® User’s Guide for SATA or SAS removable drive enclosures
●The CRU Dataport website at http://www.cru-dataport.com/htmldocs/products/dataexpress/
dx115.html
6 CRU Dataport DX115 kit installation ENWW
Step 4—Completing the workstation assembly
CAUTION: Insert or remove the carrier (with a disk drive) only when the workstation is shut down.
Other procedures may result in system hangs, data loss or even drive damage. (The component
supplier’s user guide describes a procedure for inserting or removing the carrier (with drive) while the
workstation is booted and then powering the drive via the enclosure’s power switch. Microsoft Windows
XP and Vista do not support this action.)
1. After the drive is installed in the carrier. Insert the drive carrier in the case. Press the handle in (1)
and use the key (2) to lock the carrier if shipping the unit (3).
2. Connect the power (1) and data (2) cables to the primary (upper) ports on the unit.
3. To prepare your installed hard drive for operation, refer to the appropriate hard drive
documentation.
4. If shipping the unit, use the key to lock the carrier and install the shipping screw as described in
the previous steps.
ENWW Step 4—Completing the workstation assembly 7
CAUTION: Failure to lock the drive during shipment may result in damage to your removable
hard drive system.
Failure to install the shipping screw may result in damage to the removable hard drive system.
5. Replace workstation bezel and access panel.
8 CRU Dataport DX115 kit installation ENWW
Otros manuales para Xw4400 - Workstation - 2 GB RAM
12
Este manual sirve para los siguientes modelos
10
Tabla de contenidos
Otros manuales de Hardware de computadora de HP
HP
HP NC364T Manual de usuario
HP
HP P Class 450/500/550/600/650/700/750 Manual
HP
HP E5000 Manual de usuario
HP
HP M8201R Manual de usuario
HP
HP AF079A Guía de instalación
HP
HP A5830AF-48G Manual de usuario
HP
HP 64782 Manual de usuario
HP
HP Xw8400 - Workstation - 4 GB RAM Manual de usuario
HP
HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario
HP
HP 8886 - Photosmart Camera Dock Digital Docking... Manual de usuario
HP
HP D7171A - NetServer - LPr Manual de usuario
HP
HP D7171A - NetServer - LPr Manual de instalación y operación
HP
HP P Class 450/500/550/600/650/700/750 Manual
HP
HP A1250 Series Instrucciones de montaje
HP
HP rp7420 Manual de usuario
HP
HP 64793 Series Manual de usuario
HP
HP 3000 III Series Manual de usuario
HP
HP F1381A Manual de usuario
HP
HP RDX USB 3.0 Manual de instrucciones
HP
HP 64767 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
