Honeywell T7200D Manual de operación

PRODUCT DATA

63- 4355- 4

® U.S. Registered Trademark

T7200D,E, T7300D,E,F and Q7300

Series 2000 Programmable Commercial

Thermostats and Subbases

APPLICATION

The T7200, T7300 Thermostats and Q7300 Subbases control

24 Vac commercial single zone heating, ventilating and air

conditioning (HVAC) equipment. In addition, the Q7300H

Communicating Subbase can communicate schedule

information and system instructions to other devices in a

LONWORKS®network.

FEATURES

All Models:

• 7-day programming.

• Two Occupied and two Unoccupied periods per day.

• Individual heat and cool setpoints available for

Occupied and Unoccupied periods.

• Proportional plus Integral (P+I) control eliminates

temperature fluctuations.

• Intelligent Recovery®control automatically optimizes

equipment start times based on building load.

• Intelligent Fan™ feature energizes fan continuously in

the Occupied periods. Fan can also be configured for

conventional heat or electric heat fan operation.

• Automatic or manual changeover models available.

• Universal Versaguard™ Thermostat guards available.

• Convenient overrides allow temporary setpoint

changes.

• Keypad lockout available.

T7200D,E Thermostats:

• Use on single-stage conventional (T7200D) or heat

pump (T7200E) applications.

T7300D,E Thermostats:

• Use onmultistage conventional (T7300D) or heat pump

(T7300E) applications.

• Models available with remote sensor capability.

T7300F Thermostats:

• Use on single-stage or multistage system in

conventional or heat pump applications.

• Auxiliary contacts on Q7300 can be used to interface

with C7400/W7459 Economizer System for total

integration of rooftop control.

• Remote temperature sensors available for use with

all models.

• Different levels of keypad lockout available.

Q7300 Subbase:

• Use with T7300D,E,F Thermostats.

• Auxiliary contacts can be used to interface with

C7400/W7459 Economizer System for total integration

of rooftop control.

• When used with the T7300F (revision 4 or later), the

Q7300H communicates with other network devices.

• Q7300L two stages of heat control ML7984 and V5011/

V5013 valve: stage 1 opens valve 40%; stage 2 100%.

• Q7300L provides two-speed fan control:

— Low: heat and occupied fan.

— High: cooling.

Contents

Application ........................................................................ 1

Features ........................................................................... 1

Specifications ................................................................... 2

Ordering Information ........................................................ 2

Installation ........................................................................ 5

Wiring Subbase/Wallplate ................................................ 7

Settings ............................................................................ 9

Installer Setup .................................................................. 10

Installer System Test ........................................................ 13

Programming .................................................................... 16

Operation .......................................................................... 19

General Operation Information ......................................... 21

Troubleshooting Guide ..................................................... 22

Cross Reference .............................................................. 23

Wiring Diagrams (Fig. 20-34) ........................................... 29

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

63-4355—4 2

ORDERING INFORMATION

When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the

TRADELINE® Catalog or price sheets for complete ordering number.

If you have additional questions, need further information, or would like to comment on our products or services, please write or

phone:

1. Your local Home and Building Control Sales Office (check white pages of your phone directory).

2. Home and Building Control Customer Relations

Honeywell, 1885 Douglas Drive North

Minneapolis, Minnesota 55422-4386 (800) 328-5111

In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.

International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,

Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.

SPECIFICATIONS

IMPORTANT

The specifications given in this publication do

not include normal manufacturing tolerances.

Therefore, this unitmight not exactly match the listed

specifications. This product is tested and calibrated

under closely controlled conditions, and some minor

differences in performance can be expected if those

conditions are changed.

T7200/T7300 Thermostats: See Table 1.

Q7300 Subbases: See Table 2.

Dimensions: See Fig. 1.

Finish (color): Taupe.

Table 1. T7200 and T7300 Thermostat Features.

aWallplate provided.

bConfigured in Installer Setup.

Table 2. Q7300 Subbase Features.

aDepends on model (some specific models have fewer).

bAll subbases are down selectable and can be configured to

control fewer stages than the maximum allowed.

cWithout O/B terminals.

dWith O/B terminals.

eUsed with ML7984 Actuator and V5011 or V5013 Valve.

Model Applications Subbase

Required Maximum Stages Wiring Diagram Changeoverb

Heat Cool

T7200D Conventional Nonea1120Automaticor

Manual

T7200E Heat Pump Nonea1121

T7300D Conventional Q7300A,G,L 3 3 22-23, 28, 34

T7300E Heat Pump Q7300C,D 3 2 24-27

T7300F Conventional or

Heat Pump Q7300A,C,D,G,L 3 3 22-28,34

Q7300H 3 3 29-33

Model Applications Thermostat

Required Maximum Stagesa,b

Wiring DiagramHeat Cool

Q7300A Conventional T7300D,F 2 2 22-23

Q7300C Heat Pump T7300E,F 3 2 24-26

Q7300D Heat Pump T7300E,F 3 2 27

Q7300G Conventional T7300D,F 3 3 28

Q7300HcHeat Pump T7300F 3 2 29

Q7300HdHeat Pump T7300F 3 2 30

Q7300H Conventional T7300F 3 3 31

Q7300H Conventional T7300F 2 1 32

Q7300L ConventionaleT7300D,F 2 1 34

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

3 63-4355—4

Electrical Ratings:

24 Vac, 50/60 Hz.

20 to 30 Vac, 50/60 Hz.

Batteries: No batteries required.

Auxiliary Heat and Emergency Heat Indication:

Thermostat display indicates when Auxiliary Heat or

Emergency Heat are activated.

Loss of Power: The thermostat maintains programmed times

and temperatures for the life of the product. The clock and

day information is retained for a minimum of two hours.

Light Emitting Diodes (LED):

Two user-defined LED (not available on Q7300H).

Two defined (CHECK and MAINTENANCE) LED on select

models.

System Current Draw: 6 VA maximum at 30 Vac, 50/60 Hz.

Output Relay Current Draw: See Table 3.

Table 3. Maximum Amps at 30 Vac.

Temperature:

Ratings:

Operating Ambient: 40°F to 110°F (4°C to 43°C).

Shipping: -30°F to +150°F (-34°C to +65°C).

Display Accuracy: ±1°F (±0.5°C).

Setpoint:

Range: 45°F to 95°F (7°C to 35°C).

Deadband: 2°F (1°C).

Default Settings: See Table 4.

Table 4. Default Setpoints.

Remote Sensor Wiring Temperature Offset:

Temperature offset occurs with 500 ft (157m) to

1000 ft (305m) of 2-wire cable. See Table 5.

Humidity Ratings: 5% to 90% RH, noncondensing.

Clock Accuracy: ±1 minute per month.

Table 5. Temperature Offset.

Minimum Stage Operation Time:

Minimum On (Heat and Cool): factory setting 2 minutes;

option 0 minutes.

Minimum Off (Cool and Heat Pump): factory setting

4 minutes; option 0, 1, 3, 5 minutes.

Mounting Means:

T7200: Mounts on a wallplate.

T7300: Mounts on a Q7300 Subbase.

NOTE: Wallplate and subbase mount horizontally on a wall

or outlet box with two no. 6 x 32 screws (included).

Accessories:

C7150B1004 Discharge Air Sensor: for checkout use only

(form 63-2072).

M7415 Damper Actuator (form 63-2100).

ML7984 Valve Actuator (form 95C-10753).

Q7760A Serial LonTalk® Adapter.

R8222 Switching Relay (form 60-2056).

T675A Temperature Control (form 60-2200).

T7022A1010 Remote Temperature Sensor (form 60-0247).

T7047C Remote Temperature Sensor (form 62-3050).

T7047G Remote Temperature Sensor (form 62-3050).

T7147A Remote Temperature Sensor and Override Module

(form 62-3049).

W859F Packaged Economizer (form 63-2476).

W950A System Supervisor (form 60-2351).

W7459 Economizer Logic Module (form 63-2141).

W6210/W7210 Economizer (form 63-2528).

W6215/W7215 Economizer (form 63-2544).

Approvals:

European Community Mark (CE) Listed.

Q7300H only: LONMARK® Functional Profile No. 8060,

Thermostat Object (type 09).

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the proper

disposal of an old control. If you have questions,

call Honeywell Customer Response Center at

1-800-468-1502.

Relay Running (A) Inrush (A)

Fan 0.5 2.5

Heat (all stages) 1.5 3.5

Cool (all stages) 1.5 7.5

Auxiliary (Economizer) 1.5 3.5

Control Occupied Unoccupied

Heating 70°F (21°C) 55°F (13°C)

Cooling 78°F (26°C) 90°F (32°C)

Temperature Range 18 AWG 20 AWG 22 AWG

50 to 90°F -0.4°F -0.7°F -1.0°F

10 to 32°C -0.3°C -0.4°C -0.6°C

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

63-4355—4 4

Fig. 1. Dimensions of T7200, T7300 and Q7300 in in. (mm).

Set Temperature Change

Time/Temp

Set Program

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continous

Unoccupied

Set Current

Day/Time Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

1-3/8 (35)

6-3/4 (172)

3-1/4 (82)

1-7/8

(47)

4-3/4

(121)

4-1/8

(105)

1/16 (2)

7-5/16 (186)

5 (127)

4-5/8

(117)

1-11/16

(43)

7/8

(22)

9/16

(14)

M16292

1 T7200 WALLPLATE DOES NOT HAVE THE LED EXTENSION

1-3/8 (35)

6-11/16 (170)

3-3/16 (77)

1-7/8

(47)

4-1/8

(105)

1/16 (2)

Q7300A,C,D,G,L

Q7300H

T7200D,E; T7300D,E,F

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

5 63-4355—4

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause a

hazardous condition.

2. Check the ratings given in the instructions and on the

product to make sure the product is suitable for your

application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions to

check out the product operation.

Location

Do not install the thermostat where it can be affected by:

—drafts, or dead spots behind doors and in corners.

—hot or cold air from ducts.

—radiant heat from sun or appliances.

—concealed pipes and chimneys.

—unheated (uncooled) areas such as an outside wall behind

the thermostat.

T7200 Wallplate or Q7300 Subbase without

Remote-Mounted Temperature Sensor

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 2.

Q7300 Subbase with Remote-Mounted

Temperature Sensor(s)

If only the remote-mounted temperature sensor(s) is used

to sense and control room temperature, then install the

thermostat in an area that is accessible for setting and

adjusting the temperature and settings.

If both the subbase and remote-mounted temperature

sensor(s) are used to sense and control room temperature,

then install the subbase about 5 ft above the floor in an area

with good air circulation.

Install the remote-mounted sensor(s) about 5 ft (1.5m) above

the floor in an area with good air circulation at average

temperature. See Fig. 2.

If multiple remote sensors are required, they must be

arranged in a temperature averaging network consisting of

two, three, four, five or nine sensors. See Fig. 3 through 8.

NOTES:

—When sensor averaging, the T7147A can be substituted

for the T7047C. The T7147A includes OVERRIDE and

WARMER/COOLER keys.

—Up to four T7147As can be used in parallel to place the

thermostat in Temporary Occupied.

Fig. 2. Typical location of thermostat

or remote-mounted sensor.

IMPORTANT

To avoid electrical interference, which can cause

erratic performances, keep wiring runs as short as

possible and do not run thermostat wires adjacent to

the line voltage electrical distribution systems. Use

shielded cable (Belden type 8762 or equivalent for

2-wire and Belden type 8772 or equivalent for

3-wire). The cable shield must be grounded only at

the controlled equipment case.

Fig. 3. One T7047C Sensor providing temperature

sensing for T7300/Q7300 Thermostat/Subbase.

Fig. 4. Two T7047G Sensors providing temperature

averaging network for T7300/Q7300 Thermostat/Subbase.

5 FEET

(1.5 METERS)

YES NO

NO NO

M4823A

M4839BB

SUBBASE

T7047C

M4838

SUBBASE

T7047GT7047G

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

63-4355—46

Fig. 5. Two T7047C Sensors and one T7047G Sensor

providing temperature averaging network for

T7300/Q7300 Thermostat/Subbase.

Fig. 6. Four T7047C Sensors providing temperature

averaging network for T7300/Q7300 Thermostat/Subbase.

Fig. 7. Five T7047G Sensors providing temperature

averaging network for T7300/Q7300 Thermostat/Subbase.

Fig. 8. Nine T7047C Sensors providing temperature

averaging network for T7300/Q7300 Thermostat/Subbase.

NOTE: With the thermostat configured for a temperature

averagingnetwork (remote and internal sensing), the

internal sensor has 50% authority of the averaged

temperature.

Mounting Subbase/Wallplate

The subbase/wallplate mounts horizontally on the wall or

a 2 in. by 4 in. wiring box. Position the subbase/wallplate

horizontally on the wall or on a 2 in. by 4 in. wiring box.

1. Position and level the subbase/wallplate.

NOTE: A level wallplate is only for appearance. The

thermostat functions properly when not level.

2. Use a pencil to mark the mounting holes. See Fig. 9.

3. Remove the subbase/wallplate from the wall and drill

two 3/16 inch holes in the wall (if drywall) as marked.

For firmer material such as plaster or wood, drill two

7/32 inch holes. Gently tap anchors (provided) into the

drilled holes until flush with the wall.

4. Position the subbase/wallplate over the holes, pulling

wires through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

M4839

SUBBASE

T7047C

T7047C TT

T7047G

M4840

SUBBASE

T7047C

M4841

SUBBASE

T7047G

M4842

SUBBASE

T7047C

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

7 63-4355—4

Fig. 9. Mounting subbase or wallplate.

WIRING SUBBASE/WALLPLATE

IMPORTANT

All wiring must comply with local electrical codes

and ordinances.

Follow equipment manufacturer wiring instructions when

available. Refer to the Wiring section for typical hookups.

A letter code is located near each terminal for identification.

Refer to Table 6 for terminal designations.

CAUTION

Electrical Shock Hazard.

Power supply can cause electrical shock.

Disconnect power before beginning installation.

1. Loosen the terminal screws on the subbase/wallplate

and connect the system wires. See Fig. 10.

IMPORTANT

Use 18-gauge, solid-conductor color-coded

thermostat cable for proper wiring. If using 18- gauge

stranded wire, no more than ten wires can be used.

Do not use larger than 18-gauge wire.

2. Securely tighten each terminal screw.

3. Push excess wire back into the hole.

4. Plug the hole with nonflammable insulation to prevent

drafts from affecting the thermostat.

Fig. 10. Proper wiring technique.

WIRES

THROUGH WALL

WALL

ANCHORS

(2)

M10237

LEDS

MOUNTING

HOLES

MOUNTING

SCREWS

M4826

FOR WRAPAROUND

INSERTION STRIP

7/16 IN. (11 MM).

FOR STRAIGHT INSERTION

STRIP 5/16 IN. (8 MM).

Table 6. Terminal Designations and Descriptions.

Terminal Designations Typical Connection Function Terminal

TypeStandard Alternate

A1 A2aDry auxiliary contacts for economizer control; A1 is normally open

during Unoccupied periods and closed during Occupied periods. Output Dry contact

A1, A2 —Damper control relay (Q7300L only). Input, Output 24Vpowered

contact

A2 A1aDry auxiliary contacts for economizer control (A2 is common). Input Dry contact

A3 —Dry auxiliary contacts for economizer control; A3 is normally open

during Occupied periods and closed during Unoccupied periods. Output Dry contact

AS, AS —C7150B Discharge Air Sensor connection. Input —

B—Heating changeover valve. Output 24Vpowered

contact

C1, C2, C3,

C4, C5 —Communication input for T7147. Input Low power

E K Emergency heat relay. Output 24Vpowered

contact

aSome OEM models reverse the economizer terminal designations A1 and A2.

bSome OEM models label the terminal for transformer common B.

cApplies only to Q7300H2037.

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

63-4355—48

EB, EB —Q7300H LONWORKS®bus connection to LONWORKS®network. Input, Output Communi-

cations

G F Fan relay. Output 24Vpowered

contact

O R Cooling changeover valve. Output 24Vpowered

contact

R V 24V system transformer. Input —

RC —24V cooling transformer. Input —

RH —24V heating transformer. Input —

T, T —Remote sensor input for T7047 or T7147. Input —

W1 H1, R3 Stage 1 heating relay (Q7300A,G,H) or auxiliary heat relay

(Q7300C,D,H). Output 24Vpowered

contact

W2 H2, R4, W3, Y Stage 2 heating relay. Output 24Vpowered

contact

W3 —Stage 3 heating relay. Output 24Vpowered

contact

XBb, C, X1, X2 Common. Input

X1, X3 A, A1, A2, C,

L, X, Z User defined Light Emitting Diodes (LED). Annunciation —

X4 —LED common. Annunciation —

Y1 C1, M, Y Stage 1 compressor contactor (Q7300C,D,H). Output 24Vpowered

contact

Y1, Y RS, M Stage 1 cooling compressor (Q7300A,G,Hc,L). Output 24Vpowered

contact

Y2 C2 Stage 2 cooling compressor (conventional).

Stage 2 compressor contactor (heat pump). Output 24Vpowered

contact

Y3 —Stage 3 cooling compressor. Output 24Vpowered

contact

BM —ML7984 Actuator connection (Q7300Hc, L only); no call for heat,

valve closed; call for stage 1 heat, valve approximately one-half

open; call for stage 2 heat, valve fully open.

Output —

FC —Fan control transformer (Q7300Hc, L only). Input —

GH —High-speed fan output (Q7300Hc, L only); activate during calls for

cooling. Output 24Vpowered

contact

GL —Low-speed fan output (Q7300Hc, L only); activated on calls for heat

and fan On selection. Output 24Vpowered

contact

P1, P2 —Pump interlock relay (Q7300Hc, L only); operates circulator pumpin

hydronic heat or energizes conventional heat system. Input, Output 24Vpowered

contact

RM —ML7984A Actuator connection (Q7300Hc, L only); no call for heat,

valve closed; call for stage 1 heat, valve approximately one-half

open; call for stage 2 heat, valve fully open.

Output —

—C, H, L HSII Control Panel. ——

—O Momentary circuit changeover. ——

—PDefrost. ——

—R1, R2 Low- and high-speed fan relays. ——

—T External temperature readout, T-relay; outdoor thermistor. ——

Table 6. Terminal Designations and Descriptions. (Continued)

Terminal Designations Typical Connection Function Terminal

TypeStandard Alternate

aSome OEM models reverse the economizer terminal designations A1 and A2.

bSome OEM models label the terminal for transformer common B.

cApplies only to Q7300H2037.

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

9 63-4355—4

Mounting Thermostat on Subbase/Wallplate

The thermostat mounts on the subbase/wallplate after it is

installed:

1. Engage the tabs at the top of the thermostat and

subbase/wallplate. See Fig. 11.

2. Press the lower edge of the case to latch.

NOTE: To remove the thermostat from the wall, first pull out

at the bottom of the thermostat; then remove the top.

Fig. 11. Mounting thermostat on subbase/wallplate.

SETTINGS

Using Thermostat Keys

The thermostat keys are used to:

•set current time and day,

•program times and setpoints for heating and cooling,

•override the program temperatures,

•display present setting,

•set system and fan operation,

•configure Installer Setup,

•check Installer System Test.

See Fig. 12 for key information.

Setting System and Fan (select models)

The system default setting is Heat. The fan default is set

so the fan operates continuously in Occupied periods,

Unoccupied period recovery times and with the heating and

cooling equipment in Unoccupied periods. Use the System

and Fan keys to change the settings. Fan and system

operation are configured in the Installer Setup options.

The system settings are:

—Em Heat (T7200E, T7300/Q7300C,D,H): Emergency heat

relay is on continuously. Thermostat cycles highest stage

of heat. Cooling system is off. Compressor is de-energized.

—Heat: Thermostat controls the heating.

—Off: Both the heating and cooling are off.

—Cool: Thermostat controls the cooling.

—Auto: Thermostat automatically changes between heating

and cooling depending on the indoor temperature.

The fan settings are:

—On: Fan operates continuously in occupied period.

—Auto: Equipment controls the fan in the Unoccupied

periods. The Intelligent Fan™operation (Installer Setup

number 17) offers three choices for the fan operation in

Occupied periods:

—fan turns on only when there is a call for heat or cool.

—fan operates continuously in Occupied periods.

—fan is on continuously in Occupied periods and

Unoccupied period recovery times.

Setting Temperature

Refer to Table 4 for the default temperature setpoints. See

Programming section for complete instructions on changing

the setpoints.

M4824A

B. PRESS LOWER EDGE OF CASE TO LATCH.

A. ENGAGE TABS AT TOP OF THERMOSTAT AND SUBBASE OR WALLPLATE.

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

63-4355—410

Fig. 12. Thermostat key locations and descriptions.

INSTALLER SETUP

NOTE: For most applications, the thermostat factory settings

do not need to be changed. Review the factory

settings in Table 7 and if no changes are necessary,

go to the Installer System Test section.

The installer uses the Installer Setup to customize the

thermostat to specific systems. (See Table 7.) The table

includes all the configuration options available.

A combination of key presses are required to use the Installer

Setup feature:

—To enter the Installer Setup, press and hold Heat/Cool

Settings and both the increase ▲▲ and decrease ▼▼keys

until the first number is displayed. All display segments

appear for approximatelythree seconds beforethe number

is displayed. See Fig. 13 and 14.

—To advance to the next Installer Setup number, press

Unoccupied Temp.

—To return to an Installer Setup number, press Heat/Cool

Settings.

—To change a setting, use the increase ▲ or decrease ▼ key.

—To exit the Installer Setup, press Run Program.

NOTES:

—Installer Setup is automatically exited after four

minutes with no key pressed.

—Be sure to set thermostat time after exiting

Installer Setup.

—Installer Setup numbers are listed in Table 7.

Fig. 13. LED display of all segments.

Fig. 14. Installer Setup number and setting display.

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continuous

Unoccupied

Set Current

Day/Time Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Auto

System Fan

Mon

Room

Occupied

Heat

M10233A

SET OVERRIDE

TEMPERATURE

OFFSET AND

ACTIVATE

TEMPORARY

OVERRIDE

ENTER HOLD MODE SET CURRENT

DAY AND TIME

CLEAR PROGRAM PERIOD COPY ONE

PROGRAMMED DAY

TO ANOTHER DAY

SELECT FAN

OPERATION

SELECT

SYSTEM

OPERATION

CHANGE BETWEEN HEATING

AND COOLING SETPOINTS

AND SCROLLS BACKWARDS

THROUGH INSTALLER SETUP

NUMBERS AND SYSTEM TEST

DECREASE

TEMPERATURE

OR TIME SETTING

INCREASE

TEMPERATURE

OR TIME SETTING

SET UNOCCUPIED TEMPERATURE

SETPOINTS AND SCROLLS

THROUGH INSTALLER SETUP

AND SYSTEM TEST

SET OCCUPIED

TEMPERATURE

SETPOINTS

SET CURRENT DAY OR

PROGRAM DAY

ENTER UNOCCUPIED

PROGRAM MODE

ENTER OCCUPIED

PROGRAM MODE

RETURNS TO

NORMAL

OPERATIONS

Heat

Auto

System Fan

Off Auto

Mon

Wait

Room

Remote

%Humid

Auto

Sav

Comm Cool Duct

Only

Recovery

Med

Cool

TueWedThuFriSatSun

Occupied 12 Override

M4916

Aux Ht

Em Ht

Set Program

Set Day/Time

Start Time Temporary Setting Enrg

Em Heat

M10227

MODE NUMBER

DISPLAY

(COLUMN 2

OF TABLE 8)

FACTORY SETTING

OR OTHER CHOICE

DISPLAY (COLUMN 3

OR 5 OF TABLE 8)

Otros manuales para T7200D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell T1 Pro Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual de usuario

Honeywell

Honeywell RTH6400 Series Manual de usuario

Honeywell

Honeywell RTH7000 Manual de usuario

Honeywell

Honeywell T7460A Manual de usuario

Honeywell

Honeywell T834C Manual de usuario

Honeywell

Honeywell RTHL3550 Manual de usuario

Honeywell

Honeywell FocusPRO TH6110D Manual de usuario

Honeywell

Honeywell Honeywell Thermostat PRO TH3000 Series Manual de usuario

Honeywell

Honeywell Digital Round T8775A Manual de usuario

Honeywell

Honeywell T834C Manual de usuario

Honeywell

Honeywell Round CT87A Manual de usuario

Honeywell

Honeywell T841A Manual de usuario

Honeywell

Honeywell FocusPRO 5000 Manual de usuario

Honeywell

Honeywell t87n the round Manual de usuario

Honeywell

Honeywell RTH2300 series Manual de usuario

Honeywell

Honeywell T8501 Manual de operación

Honeywell

Honeywell RTH9580 Wi-Fi Manual de usuario

Honeywell

Honeywell TRADELINE Q7100A Manual de usuario

Honeywell

Honeywell Lyric T5 W Manual de usuario

Honeywell

Honeywell RTH6400 Series Manual de usuario

Honeywell

Honeywell VisionPRO Series Manual de usuario

Honeywell

Honeywell RTH7600D Manual de usuario

Honeywell

Honeywell T7200 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario