Honeywell VisionPRO Series Manual de usuario

VisionPRO®Series with RedLINK™

Installation Guide

Wired Directly to Equipment

2 Wires for Power or

Battery Only (no wires)

2 Wires for Power or

Battery Only (no wires)

Dual Powered - C Wire or Battery

(C wire or Wire Saver required to use RedLINK accessories)

RedLINK to Equipment Interface Module

RedLINK to TrueZONE Wireless Adapter

M37817

Current display. Underlined label

signifies the current display.

Mode control buttons. Use to change

settings for Fan or System Heat/Cool.

Menu. Select options to: set schedules,

view equipment status, change IAQ

settings, access installer options*, etc.

Current status. Shows system mode

(heat/cool), outdoor temperature and

humidity (with optional outdoor sensor).

Current schedule. Shows desired

temperature and schedule status.

Indoor conditions. Shows indoor

temperature and humidity.

Current Time.

Alert Light. On when alert

message is active or system is set to Em

Heat. Flashes for battery-only power; on

continuous for 24 VAC.

microSD Card Port. Use

card to load settings and dealer

information.

Reference to key features

* Password is the date code.

Getting started

Follow these basic steps to install this

thermostat, link it with the wireless

accessories, and set installer options.

1 Installing the thermostat

2 Powering optional RedLINK accessories

3 Performing initial setup

4 Finding your password (Date Code)

• To add or remove RedLINK accessories

• To make changes to Installer Setup

• To perform an Installer Test

M34164A

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXX

XXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXXX

RoHs Compliant

Conformité RoHs

Assembled in Mexico

Assemblé au Mexique

TH8321R1001

1324

M34161A

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXXXX

RoHs Compliant

Conformité RoHs

Assembled in Mexico

Assemblé au Mexique

TH8321R1001

1324

Thermostat (back view)

Password

(Date Code)

NOTE: For best RedLINK

performance, mount thermostats at

least 2 feet apart.

1.1 Separate wallplate from

thermostat.

If your thermostat has a button

along the top of the wallplate, press

button on top and pull to remove

the wallplate as shown. Updated

models do not have this button. On

those models pull evenly along the

sides and bottom of the thermostat

to separate it from the wallplate.

1.3 Connect power.

1.3a Insert supplied AA alkaline

batteries for primary or

backup power.

NOTE: When the thermostat is

NOT used with the Equipment

Interface Module or the

TrueZONE Wireless Adapter, a C

wire is required for RedLINK.

MCR34000B

O/B

AUX

-E

L/A

CONVENTIONAL

HEAT PUMP

1.3b For 24VAC primary power,

connect common side of

transformer to C terminal.

1.2 Mount wallplate as shown.

Mount new wallplate using

screws and anchors included

with the thermostat.

Drill 3/16-in holes for drywall.

Drill 7/32-in holes for plaster.

Thermostat (back view)

Wallplate

(back view)

Wallplate

O/B

AUX

-E

L/A

Thermostat

Button

1Installing the thermostat

1.4 Wire the thermostat.

Is the thermostat wired directly to

the equipment?

• If the thermostat is wired directly

to the equipment:

a Refer to the table and wiring

diagrams on the next page.

b Turn on 24VAC NOW.

24VAC (C wire) is required to

connect RedLINK accessories.

• If the thermostat is used with an

Equipment Interface Module or

TrueZONE Wireless Adapter,

power the thermostat using Rc

and C terminals or with batteries.

NOTE: The relay outputs and

inputs on the thermostat do

not function when used with an

Equipment Interface Module or

TrueZONE Wireless Adapter.

O/B

AUX

-E

L/A

CONVENTIONAL

HEAT PUMP

O/B

AUX

-E

L/A

CONVENTIONAL

HEAT PUMP

1.5 With thermostat removed from

sub-base, insert the coin cell

battery.

NOTE: On some models the coin

cell battery compartment slides

out from the left side of the

thermostat when viewing it from

the back (not pictured).

1.6 Mount thermostat on wallplate.

NOTE: If your thermostat has

hinges at the bottom of the

wallplate as shown, insert the

thermostat into the hinges, then

push the top toward the wall

until it snaps together.

Updated models do not have

hinges. On those models push

evenly along the sides and

bottom of the thermostat to

connect it to the wallplate.

MCR34279A

Thermostat

Wallplate

Terminal Designations

Conventional System Heat Pump

Terminal Description Terminal Description

CCommon wire from secondary side of

cooling transformer (if 2 transformers). CCommon wire from secondary side of

cooling transformer.

Rc* Cooling power. Rc Cooling power.

R* Heating power. R Heating power.

W Heat Stage 1 O/B Changeover valve for heat pumps.

W2 Heat Stage 2 AUXE Backup Heat/Emergency Heat

Y Compressor Stage 1 Y Compressor Stage 1

Y2 Compressor Stage 2 Y2 Compressor Stage 2

G Fan Relay G Fan Relay

AConnect to Economizer Module or

Lighting Panel (TOD). L/A Connect to Compressor Monitor,

Zone Panel, Economizer Module or

Lighting Panel (TOD).

U1 / U1 Relay for humidification,

dehumidification, ventilation, or a

stage of heating/cooling. U1 / U1 Relay for humidification,

dehumidification, ventilation, or a

stage of heating/cooling.

S1 / S1 Input for a wired indoor, outdoor or

discharge sensor. S1 / S1 Input for a wired indoor, outdoor or

discharge sensor.

K** Connect to K on C-wire adaptor. K** Connect to K on C-wire adaptor.

* Remove factory installed jumper for two transformer systems.

** The THP9045A1098 C-wire adaptor is used on heat/cool systems when you only have four wires at the thermostat and

you would like the thermostat to be powered with a common wire. Use the K terminal in place of the Y and G terminals on

conventional or heat pump systems to provide control of the fan and the compressor through a single wire—the unused wire

then becomes your common wire. See THP9045 instructions for more information.

120

VAC

SYSTEM

TRANSFORMER

120

VAC

HUM, DEHUM OR

VENT TRANSFORM-

THERMOSTAT

POWERED

HUMIDIFIER,

DEHUMIDIFIER

OR VENTILATOR

120

VAC

SYSTEM

TRANSFORMER

THERMOSTAT

NON-POWERED

HUMIDIFIER,

DEHUMIDIFIER

OR VENTILATOR

FIELD INSTALL JUMPER

BETWEEN R AND U1

CONNECTING A HEAT OR COOL STAGE TO U1DEHUMIDIFICATION WITH LOW SPEED FAN

NONPOWERED HUMIDIFIER, DEHUMIDIFIER OR VENTILATORPOWERED HUMIDIFIER, DEHUMIDIFIER OR VENTILA

TOR

Wire the thermostat U1 terminal to the low speed fan for

dehumidiﬁcation control at the equipment as shown. The

relay can be set to normally open or normally closed in the

installer setup.

U1 terminals are normally open dry contacts when

set up for a stage of heating or cooling.

You must install a ﬁeld jumper if the stage of heat-

ing or cooling is powered by system transformer. Do

NOT install a ﬁeld jumper if the stage of heating has

its own transformer.

Normally open, dry contacts

Normally closed, dry contacts

120

VAC

SYSTEM

TRANSFORMER

THERMOSTAT

DEHUMIDIFICATION

WITH LOW SPEED FAN

FIELD INSTALL JUMPER

BETWEEN R AND U1

120

VAC

TRANSFORMER

THERMOSTAT

HEAT STAGE 3, COOL

STAGE 3, BACKUP HEAT

STAGE 2 FOR HEAT

PUMPS, OR GEOTHERMAL

RADIANT HEAT

2.1 Install batteries in RedLINK

accessories.

• Portable Comfort Control

• Wireless Outdoor Sensor*

• Wireless Indoor Sensor*

• Wireless Entry/Exit Remote*

• Wireless Vent and Filter Boost

Remote*

* Requires setup. See Installer

Setup options in Step 3.4.

2.2 Connect gateway to internet and

connect to power.

2.2a Connect RedLINK Internet

Gateway to router or modem

with Ethernet cable (RJ45).

2.2b Connect gateway’s power

cord to an electrical outlet

that is not controlled by a

wall switch.

NOTE: If the thermostat is wired

directly to the equipment, 24VAC (C

wire) is required to connect RedLINK

accessories. Turn on 24VAC before

performing initial setup in Step 3.

M36568

INTERNET

POWER

REDLINK

Initial setup options define the type of system you are installing:

• Residential or commercial

• Non-zoned or zoned

• Used with or without an Equipment Interface Module (THM5421)

• Used with or without the TrueZONE Wireless Adapter (THM4000)

3.1 Follow prompts on the screen to

select the appropriate options.

NOTE: If you are connecting the

thermostat to the TrueZONE Wireless

Adapter (THM4000), refer to the

TrueZONE instructions to link the

thermostat and RedLINK accessories.

Then go to Step 3.4.

3.2 When you see the prompt Connect

RedLINK Accessories? Touch No or Yes.

• If you select No, continue to Step 3.4.

• If you select Yes, you will be prompted

to Press Connect on New Accessories.

Continue to Step 3.3.

2.2a

2.2b

MCR33970

Connect RedLINK

Accessories?

APPLICATION

residential

2Powering optional RedLINK accessories

3Performing initial setup

3.3 Connect each RedLINK accessory.

NOTE: Accessories must be at least 2

feet away from the thermostat during

the linking process.

3.3a While the Press Connect

message is displayed (listening

mode), press and quickly release

the CONNECT button on each

new RedLINK accessory.

3.3b After a short delay (up to 15

seconds), check thermostat to

confirm the connection of each

RedLINK accessory. Touch sor

t to review the list.

3.3c Touch Done at the thermostat

after all new RedLINK accessories

are connected.

NOTE: Thermostat displays a

countdown timer while in the listening

mode. If it detects no activity for 15

minutes, it exits listening mode.

3.4 Finish the initial setup.

Finish the setup by selecting the

desired options. Touch Done after you

select the last option you want to

change.

The thermostat now displays its Home

screen and the thermostat setup is

complete.

M34150

THERMOSTAT TYPE

programmable

M33985

MCR33972

Outdoor Sensor

has been added

MCR34058

Press Connect on

New Accessories.

Listening mode

• To add or remove RedLINK accessories

• To make changes to Installer Setup

• To perform an Installer Test

Finding your password

You can find the date code

on the back of the thermostat,

1 Touch Menu.

2 Select Dealer Information.

3 Scroll down to see the Date Code.

Linking RedLINK accessories to the

thermostat

1 Touch Menu.

2 Select Installer Options.

3 Enter password (date code) and

touch Done.

4 Select Wireless Manager.

MCR33980

Wireless Manager

Reset To Defaults

MCR33977

Enter password

0 0 0 0

MCR33976

Installer Options

MCR33975

TH8321R1001

Date Code: 1324

MCR34022

Dealer Information

Installer Options

4Finding your password (Date Code)

M34164A

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXX

XXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXXX

RoHs Compliant

Conformité RoHs

Assembled in Mexico

Assemblé au Mexique

TH8321R1001

1324

M34161A

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXX

XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXXXX

RoHs Compliant

Conformité RoHs

Assembled in Mexico

Assemblé au Mexique

TH8321R1001

1324

Thermostat (back view)

Password

(Date Code)

5 Select Add Device. The screen displays

“Press Connect on New Accessories.” The

thermostat is now in listening mode.

NOTE: Accessories must be at least 2

feet away from the thermostat during

the linking process.

5a Press and quickly release the CONNECT

button on each new RedLINK

accessory.

5b After a short delay (up to 15

seconds), check thermostat to

confirm the connection of each

RedLINK accessory. Touch sor t

to review the list.

5c Touch Done at the thermostat after

all new RedLINK accessories are

connected.

NOTE: Thermostat displays a count-

down timer while in the listening mode.

If it detects no activity for 15 minutes,

it exits listening mode.

Making changes to Installer Setup

and performing an Installer Test

NOTE: Use a microSD card to save

set up time. See next page.

1 Touch Menu.

2 Select Installer Options.

3 Enter password (date code) and

touch Done.

4 Select Installer Setup or Installer Test.

5 Follow prompts on the screen to select

the desired setup options or to perform

an equipment test.

MCR33977

Enter password

0 0 0 0

MCR33976

Installer Options

MCR34015

Installer Setup

Installer Test

MCR34058

Press Connect on

New Accessories.

MCR33972

Outdoor Sensor

has been added

MCR33981

Add Device

Connected Devices

Listening mode

Using a microSD card for setup, data logs and software upgrades

Use a microSD (secure digital) card to save setup time by loading Installer Setup

settings, Dealer Information, Holiday Schedules, and Custom Reminders to multiple

thermostats. For troubleshooting help, you can save the thermostat Data Logs (Alerts

Log and Interaction Log) to a microSD card - then view them on your computer. Also

use the microSD card to upgrade the thermostat software.

Loading Dealer Information and New Thermostat Software:

1 Visit http://thermostatsetup.honeywell.com

to enter your dealer information or load new

thermostat software.

2 Connect a microSD USB Adapter to your

computer to download the file(s).

3 After the file(s) are downloaded, remove the

microSD card from the adapter and insert

into thermostat.

To use the microSD card in the thermostat:

1 Slide card into the bottom of thermostat.

2 Select the item to load or save.

3 Follow the prompts on the screen.

• To add information from the card to

the thermostat, select Load from SD Card.

• To put thermostat information on the

card, select Save to SD Card.

4 When you are finished, touch Done, then

Home, and remove the microSD card.

To replace a thermostat

When you replace a thermostat, you must reset the RedLINK

accessories before connecting them to the new thermostat.

Follow the instructions below:

At the Portable Comfort Control:

Press and hold the blank space (or arrow) in the

lower right hand corner of the screen until the display

changes (hold for about 4 seconds). Press REMOVE,

then YES to disconnect from the old thermostats. To

reconnect the thermostat, go to Step 3.2.

At the Indoor Sensor, RedLINK Internet Gateway,

Entry/Exit Remote, VentFilter Boost Remote or

TrueSTEAM Wireless Adapter:

Press and hold the CONNECT button on the accessory

until the status light glows amber (hold for about 10

seconds). To reconnect the thermostat, go to Step 3.2.

At the Equipment Interface Module (EIM):

Press and hold the CONNECT button on the EIM until

the CONNECTED LED glows amber (hold for about 10

seconds). Follow the prompts on the screen to connect

the new thermostat to the EIM.

Press and hold

Portable Comfort

Control

MCR34059

Installer Setup

Dealer Information

microSD

card

USB

adapter

Computer

microSD

card

Thermostat

Otros manuales para VisionPRO Series

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell VISIONPRO TH8321U1097 Manual de usuario

Honeywell

Honeywell Powerpile TS86A Manual de usuario

Honeywell

Honeywell Chronotherm T4600 Manual de operación

Honeywell

Honeywell T6570 Series Manual de usuario

Honeywell

Honeywell RTHL3550 Manual de usuario

Honeywell

Honeywell RTH2300 series Manual de usuario

Honeywell

Honeywell RCT8101 Manual de usuario

Honeywell

Honeywell VisionPRO 8000 Series Manual de usuario

Honeywell

Honeywell TL7230A Manual de usuario

Honeywell

Honeywell CT3200 series Manual de usuario

Honeywell

Honeywell 69-0568 Manual de usuario

Honeywell

Honeywell TrueZONE HZ432 Manual de instrucciones

Honeywell

Honeywell T8011F Manual de usuario

Honeywell

Honeywell RTH2300B Manual de usuario

Honeywell

Honeywell TH8110R1008/U Manual de usuario

Honeywell

Honeywell PRO TH3110D Manual de usuario

Honeywell

Honeywell T8002 Manual de usuario

Honeywell

Honeywell RTH1100 series Manual de usuario

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Manual de usuario

Honeywell

Honeywell Easy-To-See T87N1000 Manual de usuario

Honeywell

Honeywell RTH9585 Wi-Fi Manual de usuario

Honeywell

Honeywell RTH111 series Manual de usuario

Honeywell

Honeywell THX9000 Prestige HD Manual de usuario

Honeywell

Honeywell Y87RFC Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario