Honeywell Fire-lite FFT Manual de usuario

FFT

Fire Fighter Telephone Module

Product Installation Drawing

Document 52246 RevA 1/16/08 ECN 07-873

CAUTION! Make sure to observe all of the following precautions:

• Remove all power (AC and DC) before installing or removing any modules since damage to components

may occur if power remains applied.

• Circuit boards contain static-sensitive components. Always ground yourself with a proper wrist strap

before handling any boards so that static charges are removed from the body. Use static suppressive

packaging to protect electronic assemblies.

FFTReplacement

1. Make certain thatAC and DC power have been removed from the panel.

2. Unplug the terminal block connectors from TB1, TB2 and TB3 located on the top edge of the defective FFT board

(label to ensure reinstallation in correct positions).

3. Unplug the panel telephone handset from Phone Jack J1 located on bottom center of the defective FFT board.

4. Remove two mounting screws which hold the defective FFT board to the mounting bracket standoffs and set aside.

5. Carefully lift the defective FFT board from the slot in the bottom of the mounting bracket.

6. Remove the ribbon cable connectors from J2 on the right side of the board and J3 on the back of the defective FFT

board.

7. Connect cable between J2 on the new FFTboard and P5 on Zone Split Audio Panel main circuit board as illustrated

below.

8. If telephone call-ins are to be annunciated on the ZPM, connect cable between J3 on the FFT and P4 on the back

of the ZPM(K) module. Note that the J3 and P4 ribbon cable connectors are keyed to prevent incorrect

installation. Refer to following illustration for connector locations.

The FFTFire Fighter Telephone Module provides supervision,

annunciation and control for local and remote telephone handsets as

well as an optional remote microphone.

Audio Panel with Zone Split

Make certain that the ribbon cable is

installedwith thered stripeoriented

asillustrated below.

red stripe

Document 52246 RevA ECN 07-873 1/16/08

Standoff Standoff

Slot

Mounting Bracket

FFT

Terminal Block Connectors

J2 (on side)

TB1TB2TB3

J3 (on back)

RibbonCable

Connectors

SW1 J1

9. Insert the bottom of the new FFT board in the slot located in the bottom right of the mounting bracket as indi-

cated in illustration below.

10. Secure the module to the mounting bracket standoffs with the two mounting screws.

11. Wire the terminal blocks TB1,TB2 and TB3 as described in the illustration below. Plug the terminal block

connectors which were disconnected in step 2 into TB1, TB2 andTB3 located on the top edge of the FFT.

12. Plug the panel telephone handset into Phone Jack J1 on bottom center of FFT.

13. Set switch SW1 to correct position. SW1 positioned to the left (as illustrated below) indicates that the remote

microphone is installed. SW1 positioned to the right indicates that a remote microphone is not installed.

14. Set switch SW2 to correct position. SW2 positioned up (as illustrated below) indicates that the audio wiring to

the Remote Page Jack is configured for 2-wire Class B.

15. ReapplyAC and DC power

16. Program the host FACPfor proper operation with the Audio Panel

17. Test the panel for proper operation.

SW2

Tabla de contenidos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell LYNXDM-GSM Instrucciones de montaje

Honeywell

Honeywell PENA D MLS2000SSP Manual de instalación y operación

Honeywell

Honeywell VE4000 Series Manual de usuario

Honeywell

Honeywell EXCEL 12 W7704B1002 Manual de usuario

Honeywell

Honeywell M6410A Manual de operación

Honeywell

Honeywell S4965 Series Manual de usuario

Honeywell

Honeywell T7460B Manual de usuario

Honeywell

Honeywell SM152 Series Manual de usuario

Honeywell

Honeywell V5013N Manual de operación

Honeywell

Honeywell BA295 Compact Manual de usuario

Honeywell

Honeywell S4567A 1001 Manual de usuario

Honeywell

Honeywell AlarmNet 7845i-GSM Instrucciones de montaje

Honeywell

Honeywell V4073A Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell Elster Jeavons S100 Manual de usuario

Honeywell

Honeywell FF-SRM200P2 Manual de usuario

Honeywell

Honeywell PWT-BV Manual de operación

Honeywell

Honeywell AlarmNet IGSMHS Instrucciones de montaje

Honeywell

Honeywell 9410 Series Manual de instrucciones

Honeywell

Honeywell TrueZONE ARD Series Manual de usuario

Honeywell

Honeywell T7270A2001 Manual de usuario

Honeywell

Honeywell Esser 2 Series Manual de usuario

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manual de usuario

Honeywell

Honeywell V305 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario