Honeywell Silent Knight RA-2000 Manual de usuario

RA-2000 Remote Annunciator

Installation

The optional Model RA-2000 Remote Annunciator, shown in

Figure 1, performs the same functions as the on-board

annunciator. Operation is identical. The RA-2000 can be surface

or flush monted.

Up to 8 RA-2000s can be added to the IFP-2000 system.

Figure 1: Model RA-2000 Remote Annunciator

RA-2000 installation involves the following steps:

1. Make sure power is off at the panel.

2. Mount the RA-2000 in the desired location (see Section

“Mounting the RA-2000” ).

3. Connect the RA-2000 to the panel (see Figure 2).

4. Use the dipswitches on the back of the RA-2000 to assign

an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N

151430).

5. The RA-2000 module must be added to the system through

programming. JumpStart AutoProgramming will add the

module automatically (refer to Manual P/N 151430).

Wiring Connections

Wire the RA-2000 to the FACP as Shown in Figure 2.

Figure 2: SBUS Connections

Specifications

Mounting the RA-2000

This section of the manual describes mounting the remote

annunciator. The annunciator can be flush- or surface-mounted.

Flush Mounting

This section of the manual describes flush mounting.

Follow these steps to flush mount the RA-2000

1. The back box dimensions are 9-3/8" w x 8-3/8" h. The

minimum depth 2". The back box can be mounted prior to

the complete installation of the RA-2000 using any of the

mounting holes shown in Figure 3.

Figure 3: Back Box Mounting Holes

2. Remove knockout holes as needed for wires. See Figure 4

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 25 mA

Alarm: 50 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

Dimensions:

Flush

Mount:

Overall: 12-1/4” W x 11.5” H x 7/8” D

31.1 cm W x 29.2 cm H x 2.2 cm D

See “Flush Mounting” for back box

dimensions.

Surface

Mount:

Including trim ring:

12-1/4” W x 11.5” H x 3” D

31.1 cm W x 29.2 cm H x 7.6 cm D

Mounting Holes

Model RA-2000 Installation Instructions

2P/N 151443 Rev A

7550 Meridian Circle, Suite 100

Maple Grove, MN 55369-4927

763-493-6455 or 800-328-0103

Fax: 763-493-6475

www.silentknight.com

for backbox knockout locations

Figure 4: Back Box Knockout Locations

3. Wire the Annunciator board to the main control panel. See

Figure 2.

4. Attach the annunciator and door assembly to back box as

shown in Figure 5 using the supplied screws.

Figure 5: Attaching Annunciator/Door Assembly to

Backbox

Surface Mounting

The Model RA-2000TG/TR trim ring kit is available for use

when surface mounting.

1. Remove the desired knock out. See Figure 4.

2. To properly mount the back box, insert a single screw into

the key shaped mounting hole. Do not tighten all the way.

See Figure 6.

Place a level on top of the back box, with the back

box level insert the rest of the mounting screws.

Figure 6: Back Box Surface Mount Holes

3. Run wires to the control panel.

4. Place the trim ring over the back box as shown in Figure 7.

Figure 7: Installing Trim Ring

5. Attach the Door assembly to the back box using screws

provided.

6. After the annunciator wiring to the panel has been

completed, replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws

on the bezel.

Wire Knockouts

Key Shaped

Mounting Hole

Back Box

Mounting Holes

Tabla de contenidos

Otros manuales de Panel de control de Honeywell

Honeywell

Honeywell Symphony Manual de instrucciones

Honeywell

Honeywell GALAXY 16103 Manual de usuario

Honeywell

Honeywell TotalZone TZ-4 Manual de operación

Honeywell

Honeywell NOTIFIER AM1000 Manual del propietario

Honeywell

Honeywell Gamewell GFANN-80 Manual técnico

Honeywell

Honeywell CM737 Instrucciones de instalación

Honeywell

Honeywell Galaxy Dimension series Guía de configuración rápida

Honeywell

Honeywell MRP-2002 Manual de usuario

Honeywell

Honeywell Accenta Manual de usuario

Honeywell

Honeywell Galaxy Dimension GD-48 Manual de usuario

Honeywell

Honeywell THOR VM1 Manual de usuario

Honeywell

Honeywell IFP-2100ECS Especificaciones técnicas

Honeywell

Honeywell Vigilon 4 loop Manual de instalación y operación

Honeywell

Honeywell Notifier AFP-100 Manual de usuario

Honeywell

Honeywell ControLinks YP7999A1000 Manual de usuario

Honeywell

Honeywell NOTIFIER ID62 Hoja de instrucciones

Honeywell

Honeywell Lyric LCP300-L Manual de usuario

Honeywell

Honeywell IFP-2100 Especificaciones técnicas

Honeywell

Honeywell Silent Knight IFP-2000 Module 3 Manual de usuario

Honeywell

Honeywell NOTIFIER SLC Manual de usuario

Honeywell

Honeywell GX-Series Instrucciones de montaje

Honeywell

Honeywell Farenhyt Series Manual de usuario

Honeywell

Honeywell AQ252 Series Manual de usuario

Honeywell

Honeywell TrueZONE HZ432 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas