Honeywell NOTIFIER ID62 Hoja de instrucciones

ID61/62 installation,

commissioning &

configuration

manual

997-457-000-8, Issue 8 January 2010

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Contents

i 997-457-000-8, Issue 8

January 2010

Contents

1 Introduction 1

1.1 Manual Purpose 1

1.2 System Design and Planning 1

1.3 General 2

1.3.1 Date-dependent Functions 2

1.4 CE Marking 2

1.5 EN54 Functions 3

1.6 Ancillary Functions 4

1.7 Related Documents 5

1.8 Warnings and Cautions 5

1.9 Tips 5

1.10 Glossary of Icons 6

2 Installation Guide 7

2.1 How to Use this Section 7

2.2 Pre-Installation Check List 7

2.2.1 Some DO’s and DON’T’s 7

2.3 Transient Protection 8

2.4 Product Inspection 9

2.4.1 Checking Your Panel for Damage 9

2.4.2 What to do if Panel is Damaged or Suspect10

2.5 Dismantling the Panel 11

2.5.1 Removing the Cover(s) 11

2.5.2 Removing the Panel Electronics 12

2.5.3 Back Box Fixing 13

2.5.4 Flush Mounting Bezel (Optional) 14

2.6 Assembling the Panel 15

2.7 RS485 Communications Link 16

2.7.1 Fitting the RS485 Interface Module PCB 16

2.8 RS232 Interface Connections 17

3 Cabling 18

3.1 Cabling Instructions 18

3.1.1 Cable Terminations 19

3.2 Cable Installation Notes 20

3.2.1 Introduction 20

3.2.2 Quality of Cable and of Cable Installation 20

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Contents

ii997-457-000-8, Issue 8

January 2010

3.3 EMC Considerations 21

3.3.1 Screen Termination 21

3.3.2 Ferrite Sleeves (Optional) 21

3.4 MICC Cables 21

4 Commissioning 22

4.1 Introduction 22

4.2 Preliminary Checks 22

4.3 Internal Checks 23

4.3.1 Jumper Link Options 23

4.4 External Wiring Checks 24

4.4.1 Loop Wiring 24

4.4.2 RS485 Communications Link 25

4.4.3 DC Auxiliary Output 25

4.4.4 Sounder Circuit Outputs A and B 26

4.4.5 CFG Outputs C and D 27

4.4.6 -VE Outputs 28

4.4.7 Digital / ÜE Inputs 28

4.4.8 Switch Connections 28

4.5 Powering the Panel 29

4.5.1 Start-up Language Selection 29

4.5.2 Batteries 30

4.6 Configuration and Handover 31

4.7 Commissioning Tests 32

4.7.1 Test LEDs 32

4.7.2 Test LCD 32

4.7.3 Test Zones 32

4.7.4 Test Auto High Test 32

4.7.5 Test Outputs 32

4.7.6 Test Buzzer 32

4.7.7 Test Keyboard 32

4.8 Sensors and Modules 33

4.8.1 EN54 Requirements 33

4.8.2 Loop Wiring Testing 33

5 Configuration 35

5.1 Introduction 35

5.2 Navigation and Number Entry 35

5.3 Level 2 Configuration Options 35

5.4 Level 3 Configuration Options 36

5.5 Setup Options 37

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Contents

iii 997-457-000-8, Issue 8

January 2010

5.5.1 Panel Options 37

5.5.2 Site Details 43

5.5.3 Device Options 44

5.5.4 Peripheral Options 51

5.5.5 Day/Night Settings 59

5.6 Circuit Options 65

5.6.1 Signalling Line Circuit (SLC) - Devices 65

5.6.2 Signalling Line Circuit (SLC) - Learn 74

5.6.3 On-Board Circuits 77

5.7 Control-By-Event Output Rules 79

5.7.1 Output Type 82

5.7.2 Filter-by-type 83

5.7.3 Evacuation 84

5.7.4 Silence 84

5.7.5 Interrupt Delay 85

5.7.6 Class Change 85

5.7.7 Two Zone 86

5.7.8 Zones 87

5.7.9 Device Inputs 88

5.7.10 Soak Timer 89

5.8 Zone Texts 89

5.9 Access Options 90

5.10 System Options 92

5.10.1 Crystal Frequency 92

5.10.2 Wipe Memory 92

5.11 Normal 93

Appendix 1 - Specifications A1-1 to A1-6

Appendix 2 - ID61/62 Single Loop Panel

Differences A2-1 to A2-5

Appendix 3 - Fault Messages & Meanings A3-1 to A3-4

Appendix 4 - EN54-2 Options with

Requirements A4-1 to A4-4

Appendix 5 - Configuration of a Fault Routing

Output Using a Zone Monitor A5-1

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

1 997-457-000-8, Issue 8

January 2010

1 Introduction

1.1 Manual Purpose

The purpose of this manual is to provide the user with all

recommended procedures and full technical details for

the successful installation, commissioning and

programming of a NOTIFIER ID61/62 Series Panel.

Features of the ID61/62 Series fire control such as

VIEW™, Optiplex/SMART 2, SMART 3 and SMART 4

sensors, which require a fuller explanation of their

enhanced fire detection capabilities, are described in

Appendix 2 of this manual.

Procedures described in this manual include appropriate

warnings and cautions to guide the user towards adopting

safe and methodical work practices during the installation,

commissioning and programming phases.

The ID61/62 Series panels support OPAL protocol

devices. These devices support both OPAL and CLIP

loop polling protocols so they can be added to an existing

CLIP protocol loop. However, when OPAL protocol is

enabled on a loop a maximum of 10 CLIP devices

addresses can be supported as part of the total of 99

sensors and 99 modules.

Important Note

This manual must be read, and its content clearly

understood, before proceeding with any work relating to

the ID61/62 Series Panel. Damage to the control panel

may result from NOT following the recommended

procedures described in this manual.

This manual provides all necessary instructions for the ID61/

62 Series Panel and applies only to fire panels fitted with

compatible software.

CAUTION: In particular, care must be taken when

powering up/down any repeaters.

If there are any areas of doubt, consult your supplier

before continuing with the system installation,

commissioning and programming.

1.2 System Design and Planning

It is assumed that the system, of which the ID61/62 Series

Panel equipment is a part, has been designed by a

competent fire alarm system designer in accordance with

the requirements of EN 54 Part 14 and any other local

codes of practice that are applicable.

The design drawings should clearly show the positions

of all the ID61/62 Series Panel control equipment and

field devices.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

2997-457-000-8, Issue 8

January 2010

1.3 General

The ID61 and ID62 range of fire control panels is designed

for use with NOTIFIER’s range of addressable analogue

sensors, control and monitoring modules and addressable

call points. A unique signalling protocol is used, having

digital address and control signals and analogue pulse

width monitoring for the reply data from devices.

The serial communications interface operates under

RS485 protocol and enables communications between

the fire panel and repeaters.

While every effort is made to ensure the accuracy of the

content of this manual, the manufacturer reserves the

right to change the information without notice.

Installation

The ID61/62 Panel is easy to install providing the

recommended procedures described in this manual are

followed. To avoid inadvertent contamination of the PCB

Assembly, the manufacturer recommends it be installed

in the back box only after all other trades have completed

their tasks.

Commissioning

To commission the ID61/62 Panel, follow the recommended

procedures described in this manual. The manufacturer

recommends that during commissioning and maintenance,

ALL RS485 signal cables are disconnected at the Panel

end, BEFORE powering down the system and are

connected AFTER powering up the system.

Configuration

To configure the panel and system, carefully read and

follow the procedures given in this manual. These

procedures describe the menus that are displayed on

the Liquid Crystal Display (LCD) Unit.

Refer to the ID61/62 Series Operating Manual (ref: 997-

458-000-X) for a description of compatible addressable

Signalling Loop Circuit (SLC) analogue devices.

1.3.1 Date-dependent Functions

The calendar end date for this product is 31/12/2063

(two thousand and sixty three) and it will perform correctly

up to this date.

The calendar function has not been tested beyond

this date.

1.4 CE Marking

This panel is CE Marked to show that it conforms to the

requirements of the following European Community

Directives

Only fit the electronics

module after all the other

trades have completed

their tasks!

Only suitably-qualified

engineers must install,

commission and

configure this product

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

3 997-457-000-8, Issue 8

January 2010

:The EMC Directive 2004/108/EEC, by the application of

the following EMC Standards:

EN 61000-6-3: Electromagnetic Compatibility (EMC)

Generic emission standard for Residential,

Commercial and Light industrial environments

EN 50130-4: EMC Product family standard: Immunity

requirements for components of fire, intruder and

social alarm systems.

Low Voltage Directive 2006/95/EEC, by the application

of the safety standard:.

EN 60950-1: Safety of information technology

equipment.

The Construction Products Directive 89/106/EEC, by the

application of the following standards:

EN 54-2:1998, (Amd. 1 & 2): Fire detection and fire

alarm systems - Control and indicating equipment.

EN 54-4: 1998 (Amd. 1 & 2): Fire detection and fire

alarm systems - Power supply equipment.

1.5 EN 54 Functions

This fire control panel is designed to comply with the

requirements of EN 54 Part 2/4. In addition to the basic

requirements of EN 54-2, the panel may be configured to

conform with the following optional functions - the applicable

clauses of EN 54-2 are referenced as follows:

Options Clause

Indications:

Fault signal from fire protection equipment 7.10.4

Recording of the number of entries

into fire alarm condition 7.13

Fault signals from points 8.3

Controls:

Delay to Outputs 7.11.1

Manual or automatic switching of delays to outputs 7.11.2

Dependency on more than one alarm signal, Type B 7.12.2

Disablement of each address point 9.5

Test condition 10

Outputs:

Fire alarm device(s) 7.8

Fire alarm routing equipment 7.9.1

Fire alarm routing equipment with alarm confimation 7.9.2

Automatic fire protection equipment: Type A 7.10.1

Automatic fire protection equipment: Type C 7.10.3

Fault warning routing equipment 8.9

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

4997-457-000-8, Issue 8

January 2010

The following features are provided by the Power Supply Unit

(PSU) of the ID61/62 Series Panel to comply with EN 54-4.

Features of the ID61/62 EN 54-4

Power Supply Unit (PSU) Clause

Derive power from the mains supply 5.1

Derive power from and monitor a

standby battery source 5.2

Derive power supply from and monitor a

standby battery source 5.3

Detect and signal various PSU faults 5.4

1.6 Ancillary Functions

The following is a list of ancillary functions that are provided

by the ID61/62 Series panel in addition to the those

required by EN 54-2/4. These functions are described in

the section of this manual as referenced (except those

marked thus ‘*’ which are described in 997-458-000-X,

ID61/62 Series Panel - Operating Manual):

Ancillary Manual

Functions Section Refs.

Site Specific Setup Options 5.5

Access Options 5.9

Voltage Indications *4.11.7

Control-by-Event 5.7

Output modes 5.7.1

Input type pattern 5.7.9

Disable/enablement *4.9

Repeater interface 2.7

Self-learn configuration - manual 5.6.1

Self-learn configuration - auto 5.6.2

Module supervision options 5.6.1

Module silence options 5.7.4

Text editing 5.8

Sensor LED blinking on/off 5.5.7

Bell pulsing ratio 5.5.8

Display of alarm count *4.11.6

Extend delay timer 5.5.3

Sounder Volt-free contact options 4.4.5

Relay drive output option 4.4.6

Extinguishing system features 5.5.3.7, 5.5.3.8, 5.5.3.9

5.7.1, 5.7.2, 5.7.10

CAUTION:

This product is not compliant

with EN 12094-1.

12094-1

Fire extinguishing installations in

Europe are required to be certified as

compliant to this standard.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

5 997-457-000-8, Issue 8

January 2010

1.7 Related Documents

This manual only describes the installation,

commissioning and configuration of the ID61/62 Series

Panel. All operating functions are covered by the:

ID61/62 Series Panel Operating Manual (ref: 997-458-

000-X)

The Panel can support repeaters via the RS485

communications link. This manual does not provide

details about the repeaters or Compact Mimics; these

are described in:

IDR-2A, -2P & -6A Repeaters User Manual

(ref: 997-411-000-X).

IDR Mimic Installation and Commissioning Manual

(ref: 997-412-000-X).

Compact Mimic Installation Instructions (ref. 997-497-

000-X).

Note: The ‘000’ part of the manual reference is the UK

country code for the manual.

The ID51/52 Panel can also support the VIEWTM sensor.

This manual does not attempt to cover all the VIEWTM sensor

programming and calibration issues as these are described

in some detail in the following document, which is available

from NOTIFIER’s Technical Support Department:

VIEWTM Application Guide (ref: 997-198).

1.8 Warnings and Cautions

Where appropriate, the manual includes advisory

warnings and cautions to remind you to consider safety

at all times, especially when following the procedures

described herein.

You are alerted to any areas where high voltage [i.e. non-

Safety Extra-Low Voltage (SELV)] is present, or where

there may be a risk of damage to static-sensitive devices

if the recommended procedures described in this manual

are not followed.

An example of a high voltage warning and an anti-static

caution is provided to the left of this paragraph.

The ID61/62 Series Panel incorporates some features

which, if used inappropriately, may contravene the

requirements of EN 54. Where there is a possibility of

such an occurrence, a suitable warning is given with brief

details of the EN 54 requirement. A typical EN 54 non-

compliance warning is illustrated at left.

1.9 Tips

‘Handy tips’ are included, where appropriate, to assist

you in following quick and safe procedures for fire

detection system installation and integration.

Look for the ‘TIP!’ icon and supporting text, typically

illustrated at left.

Magnetise the tip of your

screwdriver to help when

offering small screws to

holes in confined spaces.

WARNING: High Voltage!

Take suitable precautions to

avoid electric shock.

EN 54-2:-8.8

One hardware-

configurable output

must be configured

as a fault relay.

ID61/62 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

6997-457-000-8, Issue 8

January 2010

1.10 Glossary of Icons

Throughout this manual, and the other related ID61/62

Series Panel manuals, a number of icons are used either

as part of the illustrated process descriptions, or in the

main text to help clarify, or simplify, particular

configuration procedures.

The following icons are used to advise or indicate:

a. DO follow the recommended procedure or method.

b. DO NOT use this procedure or method.

c. Inspection of an item or sub-assembly is required at

this point.

d. Following a defined process meets/does not meet

the required approval/inspection criteria or standards.

e. Additional items to be considered.

f. This icon placed next to a pushbutton requires you to

press it while configuring the panel. Where two or

more icons are used, a number may be placed on or

near each hand to indicate the order of selection: 1

coming before 2.

g. Activity process step - flow arrow for single action or

iterative actions.

h. Leader arrow - used with activity processes.

i. Internal buzzer operating/not-operating or silenced.

j. Sounder operating/not-operating or silenced.

k. Power connected and switched ON/disconnected and

switched OFF.

l. Manual Call Point (MCP)/Sensor.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de Honeywell

Honeywell

Honeywell NFS-3030 Instrucciones de instalación y funcionamiento

Honeywell

Honeywell NOTIFIER NFW-100X Manual de usuario

Honeywell

Honeywell Notifier NFS-320/E/C Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manual de usuario

Honeywell

Honeywell NOTIFIER NFW-50X Manual de usuario

Honeywell

Honeywell Accenta Manual de usuario

Honeywell

Honeywell Tuxedo Touch Wi-Fi Instrucciones de montaje

Honeywell

Honeywell Silent Knight RA-2000 Manual de usuario

Honeywell

Honeywell HCM 200 Manual de usuario

Honeywell

Honeywell GX-Series Instrucciones de montaje

Honeywell

Honeywell VARIODYN D1 Comprio Manual técnico

Honeywell

Honeywell TotalZone TZ-4 Manual de operación

Honeywell

Honeywell AQ255 Series Manual de operación

Honeywell

Honeywell TrolATemp TZ-3 TotalZone Manual de operación

Honeywell

Honeywell Domonial CMI 800++ Guía del usuario

Honeywell

Honeywell FCI Gamewell Flex 404 Manual de usuario

Honeywell

Honeywell Notifier AFP-100 Manual de usuario

Honeywell

Honeywell PC8900A Manual de usuario

Honeywell

Honeywell Galaxy 16 Manual de usuario

Honeywell

Honeywell Notifier ID3000 Series Manual de usuario

Honeywell

Honeywell SLC Manual de usuario

Honeywell

Honeywell AQ25A Series Manual de usuario

Honeywell

Honeywell Notifier ST.PL4+ Manual de usuario

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas