Honeywell Silent Knight 5860 Manual técnico

5860/5860R

Remote Fire Annunciator

Product Installation Document

Document 151042:E 2/15/2022 ECN: 151062

1 Description

The 5860 (gray) and 5860R (red) are optional 4x20 remote annunciators

that can be surface or flush-mounted.

2 Compatibility

The 5860/R is compatible with Honeywell Silent Knight FACPs. For

more information, see the FACP Installation manual.

3 Specifications

4 Installing the 5860/R

5860/R installation involves the following steps:

1. Ensure power is turned off at the panel.

2. Mount the 5860/R in the desired location.

3. Connect the 5860/R to the panel (see Figure 5).

4. Use the DIP switches on the back of the 5860/R to assign an ID

number. See the FACP Manual for more details.

5. The new 5860/R module must be added to the system through

programming. The JumpStart®Auto-programming feature will add

the module automatically. Refer to the FACP Manual for more

information.

5 Mounting

The 5860/R comes from the factory fully assembled. You must disas-

semble it for mounting. To disassemble the annunciator, use a 5/64” hex

wrench to remove the set screws, located on the bottom of the annuncia-

tor bezel.

FIRE ALARM ANNUNCIATOR

Figure 1 5860/R Remote Annunciator

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 58 mA

Alarm: 68 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

1".25

(3.175cm)

6.44"

(16.35cm)

8"(20.64cm).125

7".375

(18.73cm)

1”

.25

(3.175cm)

Figure 2 Annunciator Dimensions

backbox bezel

side

view

5860/5860R Installation Document — P/N 151042:E 2/15/2022 2

5.1 Surface Mounting

The 5860/R can be mounted directly to a surface or can be attached to a

single, double, or four-square electrical box. Trim Ring Kit 5860TG

(gray) and 5860TR (red) available for use when surface mounting.

1. Drill holes in the surface to match the screw holes on the backbox.

Refer to Figure 4.20 for locations.

2. Fit the trim ring over the backbox, if used.

3. Attach the backbox to the wall using screws provided.

5.2 Flush-Mounting

1. Cut a hole in the sheet rock to the following dimensions: 8.25” W x

6.625” H. If an electrical box is used, the box must be 1.375” back

from face of wall to accommodate the annunciator.

2. Remove knockout holes as needed for wires.

3. Fit the annunciator backbox into the hole and stabilize with

mounting wires. Angle the mounting wires into the first hole past

the sheet rock. Secure the wires behind the screws as shown in

Figure 4. When all four wires are in place, the backbox should fit

snugly into the hole in the sheetrock.

4. After the annunciator wiring to the panel has been completed (refer

to Figure 4.22), replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws on the

bezel.

5.2.1 Flush-Mounting with an Electrical Box

The 5860/R annunciator can be used with the following types of electri-

cal boxes: 4S, single-gang, and double-gang.

If an electrical box is used, the box must be 1.375” back from the face of

the wall to accommodate the annunciator. Studs used with an electrical

box must be 2x4” (or larger).

6 Wiring Connections

Wire the 5860/R to the FACP as shown below.

Figure 3 Trim Ring for Surface-mounting

backbox

trim ring

Attach second set of wires to top of backbox.

Secure wires behind screw.

Insert wires at an angle into the

first holes past sheetrock.

Figure 4 Flush Mounting the Backbox

SBUS OUT

–+AB

SB SA S+ S-

12345

Figure 5 SBUS Connections

5860/R

FACP SBUS

supervised,

power-limited,

Class B

Este manual sirve para los siguientes modelos

Otros manuales de Panel de control de Honeywell

Honeywell

Honeywell Gamewell GFANN-80 Manual técnico

Honeywell

Honeywell Symphony Manual de instrucciones

Honeywell

Honeywell Gamewell Flex 402 Manual de usuario

Honeywell

Honeywell TrueZONE HZ432 Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms MS-9600 Manual de usuario

Honeywell

Honeywell Accenta Manual de usuario

Honeywell

Honeywell NOTIFIER Pearl Guía de instalación

Honeywell

Honeywell VARIODYN D1 Comprio Manual técnico

Honeywell

Honeywell nfs2-3030 Manual del propietario

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manual de usuario

Honeywell

Honeywell Farenhyt Series Manual de usuario

Honeywell

Honeywell NOTIFIER RP1r Manual de usuario

Honeywell

Honeywell Vigilon 4 loop Manual de instalación y operación

Honeywell

Honeywell THOR VM1 Manual de usuario

Honeywell

Honeywell AQ25A Series Manual de usuario

Honeywell

Honeywell Domonial cmi Manual de usuario

Honeywell

Honeywell Excel 5000 System Series Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms ES-1000X Manual de usuario

Honeywell

Honeywell RS-232 Manual de usuario

Honeywell

Honeywell HVC0001 Manual de usuario

Honeywell

Honeywell TrueZONE HZ221 Manual de usuario

Honeywell

Honeywell Galaxy Flex Manual de usuario

Honeywell

Honeywell Ademco Accord Manual de usuario

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas