Honeywell RS-232 Manual de usuario

INSTALLATION

INSTRUCTIONS RS-232 Interface /

SerialPrinterPort

K1148-X 4/98

1 2 3 4 5 6 7 8

Figure1:Connector

RJ-45

FemaleDB-9 Back view

21345 6789

Pin DCE DTE

1 DCD DCD

2 RXD TXD

3 TXD RXD

4 DSR DTR

5 GND GND

6 DTR DSR

7 RTS CTS

8 CTS RTS

Figure 3: Signal Lines: Interface RJ-45 connector

Bl R G O Bk Y Gy/Wh Br

Figure 2: Signal Lines (Female DB-9 Front view)

Pin DCE DTE

1 DCD DCD

2 RXD TXD

3 TXD RXD

4 DSR DTR

5 GND GND

6 DTR DSR

7 RTS CTS

8 CTS RTS

Wire colors from RJ-45

Install crimp pins in matching

DB-9 locations as shown on

the left.

21345

6789 NOTE: Location 9 on DB-9 is empty.

The hardware in this package provides an RS-232 interface to a Destiny control panel (model Des-

tiny 6100, software version 8.04 or later). The interface can be used to provide 2-way communica-

tion with a personal computer, Remote System Mode with an RS-232 equipped controller, or to send

a real-time log of system events to a serial printer.

NOTE: Observe the drawing

and the connector used and

verify the color codes are

equivalent.

Serial Printers:

If your serial printer requires a

male 9 or 25 pin connector, you

can get a gender changer at an

electronics store. Destiny 6100

panel software supports only

GND, TXD, and RXD control

lines. Some printers require

additional control lines. You

may need to jumper these control

lines in order to use such print-

ers. Consult your printer manual

for further information.

Signal Lines:

Figure 2 shows the configuration

of signal lines in the RJ-45/DB-9

converter when wired as shown

in Figure 1. Pin 1 for the RJ-45

connector (J4) is closest to the

top of the board. Figure 3 shows

the signal lines used in a custom

installation with a DB-9 connec-

tor at J1 on the RS-232 board.

The signal lines listed on the RS-

232 Board pertain to this custom

installation, not to the standard

RJ-45.

Downloaded from - http://www.guardianalarms.net

Cable:

TheRS-232 interfaceis attachedto aRJ-45 to

DB-9 connector with either a 4 conductor or 8

conductor “phone” cable. The cable is NOT pin

compatiblewithstandard4conductorphonecords.

See Figure 2: Connection Cable. For a

4 conductor cable only pins 3,4,5,6 on the RJ-45

connector will be used. As of software revision

8.04 only pins 3,4,5,6 are supported eliminating

the necessity for 8 conductor connections.

DTE vs. DCE:

TheRS-232interfacecanoperateineitherDateTerminalEquipment(DTE)orDataCommunicationEquipment

(DCE)mode. A jumper (J3)is located tothe right ofthe RJ-45 ontheinterface board. Attachthesupplied

jumperacrossthe centerandbottompin forDCEoperationor thetoptwopins forDTE. Mostapplications

will require DCE including connection to a PC and a printer.

Protocol:

The2-wayRS-232standardfortheDestinycontrol

panelisanopenstandardandisavailablebycalling

TechnicalSupport at 800-272-7937.

Printer Reports:

When enabled (as described in Programming, above), any event programmed to appear in the Event

Memory Log will be printed when an event occurs. All items in the system that can be sent to a central

station will be printed as the event occurs. The “Report to Central Station” programming option does

not affect the printer report.

Note: the RS-232 does not buffer events, if a printer is off-line the event will not be printed.

4 Conductor Cable: Top View

8 Conductor Cable: Top View

Figure 2: Connection Cable

Br Bl Y G R Bk O Gy Br Bl Y G R Bk O Gy

YGRBkYGRBk

Programming:

The following programming options are provided:

001 - Enable the RS-232 adapter

002 - Enable printer compatibility

004 - Use English Line text (for printers only)

008 - Enable 2-Way RS-232 communication (for PC connections)

064 - Enable Remote System Mode

Place the system into program mode (default: 9,1,7,3), enter location 0,1,5,5 and then enter the sum of

options to be enabled. For example, to enable 2-way communication, enter 0,0,9 (001 + 008). For

printing, enter 0,0,7 (001 + 002 + 004).

Format:

The following is an example of the printer output when connected to the RS-232 port.

Event User Time Month Day

Open - System Disarmed User = 01 13:23 July 29

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de Honeywell

Honeywell

Honeywell PL-1000 Manual de usuario

Honeywell

Honeywell NOTIFIER NFW-50X Manual de usuario

Honeywell

Honeywell 6820 Manual de usuario

Honeywell

Honeywell Notifier ID50 Hoja de instrucciones

Honeywell

Honeywell MINI-ZONE 69-1361 Guía de inicio rápido

Honeywell

Honeywell Pro-Watch 7000 Manual de usuario

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manual de capacitación

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manual de usuario

Honeywell

Honeywell IQ8Control C Manual de usuario

Honeywell

Honeywell Galaxy 16 Manual de usuario

Honeywell

Honeywell Morley-IAS ZX Series Guía de inicio rápido

Honeywell

Honeywell Fire-Lite MS-5UD-3 Manual de usuario

Honeywell

Honeywell AQ252 Series Manual de usuario

Honeywell

Honeywell PC8900A Manual de usuario

Honeywell

Honeywell MiniZone EMM-3 Manual de operación

Honeywell

Honeywell IFP-300 Especificaciones técnicas

Honeywell

Honeywell Notifier RP-2001 Manual de usuario

Honeywell

Honeywell Silent Knight INTELLIKNIGHT 5600 Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell Notifier ID3000 Series Guía

Honeywell

Honeywell NOTIFIER AM-8200 Manual del propietario

Honeywell

Honeywell Notifier NFS-320 Manual de usuario

Honeywell

Honeywell Silent Knight SKE Series Manual de usuario

Honeywell

Honeywell AQ254 Series Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas