Honeywell Vuquest 3310g Manual de usuario

™

Vuquest™ 3310g

Area-Imaging Scanner

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in speci-

fications and other information contained in this document without prior notice,

and the reader should in all cases consult HII to determine whether any such

changes have been made. The information in this publication does not repre-

sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnish-

ing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, repro-

duced, or translated into another language without the prior written consent of

HII.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Web Address: www.honeywellaidc.com

Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows

XP, and the Windows logo are trademarks or registered trademarks of Microsoft

Corporation.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Product Agency Compliance - Vuquest 3310

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for

help.

If necessary, the user should consult the dealer or an experienced radio/

television technician for additional suggestions. The user may find the fol-

lowing booklet helpful: “Something About Interference.” This is available at

FCC local regional offices. Honeywell is not responsible for any radio or

television interference caused by unauthorized modifications of this equip-

ment or the substitution or attachment of connecting cables and equipment

other than those specified by Honeywell. The correction is the responsibil-

ity of the user.

Use only shielded data cables with this system. This unit has been tested

with cables less than 3 meters. Cables greater than 3 meters may not meet

class B performance.

Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell may void the FCC authorization to oper-

ate this equipment.

UL Statement

UL listed: UL60950-1.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Opera-

tion is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe B est conforme à la norme NMB-003

du Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

cUL Statement

cUL listed: CSA C22.2 No.60950-1-07.

Europe

The CE marking indicates compliance to 2004/108/EC EMC Directive

with Standards EN55022 CLASS B, EN55024, EN61000-3-2,

EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage Direc-

tive, when shipped with recommended power supply.

For further information please contact:

Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Honeywell International Inc. shall not be liable for use of our product with

equipment (i.e., power supplies, personal computers, etc.) that is not CE

marked and does not comply with the Low Voltage Directive.

Waste Electrical and Electronic Equipment

Information

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PAR-

LIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical

and electronic equipment (WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health

and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to

use the appropriate take-back systems for product disposal. Those sys-

tems will reuse or recycle most of the materials of the product you are dis-

posing in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you to

use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling sys-

tems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environ-

mental performances of this product.

Germany

If your product is marked with the GS symbol, then the product

has been issued a GS certificate showing compliance to EN

60950-1, Second Edition.

This device is not intended for use in direct field of view at visual

display workplaces. To avoid distracting reflections at visual dis-

play workplaces, this device should not be placed in direct field

of view.

South Korea

This product meets Korean agency approval.

Taiwan

If the following label is attached to your product, the product meets Taiwan

agency approval:

BSMI Standard: CNS13438, CNS14336-1

依據標準 : CNS13438, CNS14336-1

International

LED Safety Statement

LEDs have been tested and classified as “EXEMPT RISK GROUP” to the

standard: IEC 62471:2006.

CB Scheme

Certified to CB Scheme IEC 60950-1, Second Edition.

Patents

For patent information, please refer to www.honeywellaidc.com/patents.

Solids and Water Protection

The Vuquest 3310 has a rating of IP53, immunity of foreign particles and drip-

ping water.

Warning

To reduce the possibility of heat-related injuries, avoid touching sec-

tions of the scanner that feel warm.

Caution

To maintain compliance with standards when not powering the imager

with the optional power supply, the power source should be listed and

meet applicable requirements for a limited power source or a Class 2

power supply with rating: 5 - 5.2 Vdc, 1.0 A minimum.

Required Safety Labels

Scanner

Compliance

Label

location

Part Number,

Serial Number

and Revision

Information

location

Illumination output

Chapter 1 - Getting Started

About This Manual ...................................................... 1-1

Unpacking Your Device............................................... 1-1

Connecting the Device ................................................ 1-1

Connecting with USB ............................................ 1-1

Connecting with Keyboard Wedge........................ 1-2

Connecting with RS232 Serial Port....................... 1-3

Reading Techniques ................................................... 1-4

Menu Bar Code Security Settings ............................... 1-4

Setting Custom Defaults ............................................. 1-5

Resetting the Custom Defaults ................................... 1-5

Resetting the Factory Defaults.................................... 1-6

Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1

Programming the Interface - Plug and Play ................ 2-1

Keyboard Wedge................................................... 2-1

Laptop Direct Connect........................................... 2-1

RS232 Serial Port.................................................. 2-2

USB IBM SurePos................................................. 2-2

USB PC or Macintosh Keyboard........................... 2-3

USB HID................................................................ 2-3

USB Serial............................................................. 2-3

Verifone®Ruby Terminal Default Settings ............ 2-4

Gilbarco®Terminal Default Settings ..................... 2-5

Honeywell Bioptic Aux Port Configuration............. 2-5

Datalogic™ Magellan©Bioptic Aux Port

Configuration.................................................... 2-6

NCR Bioptic Aux Port Configuration...................... 2-6

Wincor Nixdorf Terminal Default Settings ............. 2-7

Wincor Nixdorf Beetle™ Terminal

Default Settings............................................... 2-7

Keyboard Country Layout ........................................... 2-8

Keyboard Style.......................................................... 2-15

Table of Contents

Keyboard Conversion ................................................2-16

Control Character Output...........................................2-17

Keyboard Modifiers....................................................2-17

RS232 Baud Rate......................................................2-20

RS232 Word Length: Data Bits, Stop Bits,

and Parity ...............................................................2-21

RS232 Receiver Time-Out.........................................2-22

RS232 Handshaking..................................................2-22

RS232 Timeout....................................................2-23

XON/XOFF ..........................................................2-23

ACK/NAK .............................................................2-23

Scanner to Bioptic Communication............................2-24

Scanner-Bioptic Packet Mode .............................2-24

Scanner-Bioptic ACK/NAK Mode.........................2-25

Scanner-Bioptic ACK/NAK Timeout.....................2-25

Chapter 3 - Input/Output Settings

Power Up Beeper ........................................................3-1

Beep on BEL Character...............................................3-1

Trigger Click.................................................................3-1

Good Read and Error Indicators..................................3-2

Beeper – Good Read.............................................3-2

Beeper Volume – Good Read................................3-2

Beeper Pitch – Good Read....................................3-3

Beeper Pitch – Error ..............................................3-3

Beeper Duration – Good Read ..............................3-3

LED – Good Read .................................................3-4

Number of Beeps – Good Read ............................3-4

Number of Beeps – Error.......................................3-4

Good Read Delay ..................................................3-5

User-Specified Good Read Delay..........................3-5

Manual Trigger Modes.................................................3-5

Serial Trigger Mode .....................................................3-6

Read Time-Out ......................................................3-6

Presentation Mode.......................................................3-6

Presentation LED Behavior after Decode..............3-7

Otros manuales para Vuquest 3310g

Tabla de contenidos

Otros manuales de Lector de código de barras de Honeywell

Honeywell

Honeywell 8680i Series Manual de usuario

Honeywell

Honeywell 8680i Series Manual de usuario

Honeywell

Honeywell MK3480-30B104 - IS3480 QuantumE - Wired Desktop Barcode... Manual de usuario

Honeywell

Honeywell MX7 Tecton Manual de usuario

Honeywell

Honeywell MX7 Tecton Manual de usuario

Honeywell

Honeywell Metrologic 3780 Manual de usuario

Honeywell

Honeywell N431X Manual de usuario

Honeywell

Honeywell XENON 1900 Manual de usuario

Honeywell

Honeywell 8600 Manual de usuario

Honeywell

Honeywell Voyager 1452g Series Manual de usuario

Honeywell

Honeywell IS4921 Guía de configuración rápida

Honeywell

Honeywell Hyperion 1300G Manual de usuario

Honeywell

Honeywell 3800 Linear Series Manual de usuario

Honeywell

Honeywell Eclipse MS5100 Series Manual de usuario

Honeywell

Honeywell YJ-HF5000 Manual de usuario

Honeywell

Honeywell DCS19W Manual de usuario

Honeywell

Honeywell Voyager 1450g Series Manual de usuario

Honeywell

Honeywell 3820 Manual de usuario

Honeywell

Honeywell MS4980 Manual de usuario

Honeywell

Honeywell Xenon 1910 Manual de usuario

Honeywell

Honeywell 3800gPDF - Hand Held Decoding Linear Imager Manual de usuario

Honeywell

Honeywell 3800 Linear Series Manual de usuario

Honeywell

Honeywell PX4-6IE-CUTR-IG-1 Manual de usuario

Honeywell

Honeywell XENON 1902 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario