Hitachi L300P Series Guía de inicio rápido

Otros manuales para L300P Series

7

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Inversor de Hitachi

Hitachi

Hitachi SH1 Series Guía del usuario

Hitachi

Hitachi J300 Series Manual de usuario

Hitachi

Hitachi SJ-PB(T) Manual de usuario

Hitachi

Hitachi L2002 Manual de usuario

Hitachi

Hitachi L100 IP Series Manual de usuario

Hitachi

Hitachi L100-004HFE Manual de usuario

Hitachi

Hitachi SJ200 Series Manual de usuario

Hitachi

Hitachi SJ200 Series Manual de usuario

Hitachi

Hitachi SJ100 Series Manual de usuario

Hitachi

Hitachi HFC-VWS3D Series Manual de usuario

Hitachi

Hitachi L100 Series Manual de usuario

Hitachi

Hitachi SJ Series Manual de lista de piezas

Hitachi

Hitachi J300U Series Manual de usuario

Hitachi

Hitachi air core 600 Manual de instrucciones

Hitachi

Hitachi L200 Series Manual de usuario

Hitachi

Hitachi X200 Series Manual de usuario

Hitachi

Hitachi L100DN DeviceNet Series Addendum Hoja de instrucciones

Hitachi

Hitachi SJ700-055-110LF 2 Series Manual de usuario

Hitachi

Hitachi SJ Series Manual de lista de piezas

Hitachi

Hitachi WJ200 Series Software Manual de usuario

Hitachi

Hitachi L300P Series Manual de usuario

Hitachi

Hitachi X200-002SFE/NFU Manual

Hitachi

Hitachi WJ-0001S Manual de usuario

Hitachi

Hitachi SJ700-2 Series Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario

Hitachi America, Ltd.

EN-021302-1

ENGINEERING NOTE

SUBJECT: Parameter A85, Operation Mode Selection

AFFECTED MODELS: L300P and SJ300

The manuals for the SJ300 and L300P show three settings for Parameter A85.

This is ONLY correct for the SJ300.

There are only TWO settings for the L300P: “00” for Normal Operation, and “01”

for Energy-Saving Operation. The latter setting seeks to adjust the output voltage

at any given output frequency to minimize the motor current, and hence power

consumption at that speed. This function only acts at constant speed – not during

acceleration or deceleration.

Optimal Accel/Decel Operation (SJ300 ONLY)

In addition to “Normal” and “Energy Saving” modes, the SJ300 offers a third

setting option, “02” for Optimal Accel/Decel Operation. This function is an

implementation of a “fuzzy logic” algorithm. In real time, the function

automatically adjusts the acceleration and deceleration times in response to

changes in load or inertia, to take advantage of the maximum output current

capability of the inverter. In general, this mode will allow for the shortest accel

and decel times based on the actual load conditions. The function continuously

monitors output current and DC bus voltage to ensure that their respective trip

levels are not reached. In this mode, the settings of acceleration and deceleration

times (F002 and F003) are disregarded.

The acceleration time is controlled to maintain output current below the level set

by the Overload Restriction Function if enabled (Parameters B21/B24, B22/B25,

and B23/B26). If Overload Restriction is not enabled, then the current limit used

is 150% of the inverter’s rated output current.

The deceleration time is controlled so that the output current is maintained below

150% of the inverters rated current, AND the DC bus voltage is maintained below

the OV Trip level (358V or 770V).

PGC - 2/13/02 Page 1 of 2

EN-021302-1

Notes and Precautions

1. Do not use this setting (A85 = 02) on a machine where a constant

acceleration and/or deceleration time is desired.

2. Do not use this setting (A85 = 02) if the load inertia exceeds about 20 times

the motor shaft inertia.

3. Do not use this setting (A85 = 02) if the inverter will increase and decrease

speed frequently, as nuisance trips may occur.

4. Do not use this setting (A85 = 02) if internal or external regenerative braking

is being used.

5. Do not use this setting (A85 = 02) with any of the Vector Control modes

(A44 = 03, 04, or 05). This function is ONLY compatible with V/F Control

modes (A44 = 00, 01, or 02).

6. If the load exceeds the rating of the inverter, the acceleration time may be

increased.

7. If using a motor the capacity of which is one size smaller than the inverter

rating, enable the Overload Restriction function (B21/B24) and set the

Overload Restriction Level (B22/B25) to 1.5 times the motor nameplate

current.

8. Be aware that the acceleration and deceleration times will vary depending on

the actual load conditions that exist during each individual operation of the

inverter.

PGC - 2/13/02 Page 2 of 2