Hirschmann SPIDER PL Manual de usuario

Installation SPIDER PL

Release

09/2018

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Rail Switch

SPIDER Premium Line

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation SPIDER PL 9/12/18

Installation SPIDER PL

Release

09/2018 3

Contents

Safety instructions 5

About this Manual 13

Key 14

1 Description 15

1.1 General device description 15

1.2 Device name and product code 16

1.3 Device view 18

1.3.1 Front view 18

1.4 Power supply 20

1.5 Ethernet ports 21

1.5.1 Pin assignments 22

1.6 Display elements 23

1.6.1 Device state 23

1.6.2 Port status 24

2 Configuration interface 25

2.1 USB interface 25

3 Signal contact 26

4 Installation 27

4.1 Checking the package contents 27

4.2 Mounting the device 28

4.2.1 Installing the device onto the DIN rail 28

4.2.2 Mounting on a flat surface 30

4.3 Grounding the device 31

4.4 Installing an SFP transceiver (optional) 31

4.5 Connecting the terminal block 32

4.6 Operating the device 33

4.6.1 Installing terminal blocks, switching on the supply

voltage 33

4.6.2 Connecting data cables 33

4Installation SPIDER PL

Release

09/2018

5 Configuration (optional) 34

5.1 Configuration readout 39

6 Monitoring the ambient air temperature 40

7 Maintenance and service 41

8Disassembly 42

8.1 Removing an SFP transceiver (optional) 42

8.2 Removing the device 43

9 Technical data 45

9.1 General technical data 45

9.2 Dimension drawings 47

9.3 Stability 49

9.4 Electromagnetic compatibility (EMC) 50

9.5 Network range 52

9.6 Power consumption/power output 55

10 Scope of delivery, order numbers and

accessories 56

11 Underlying technical standards 59

A Open Source Software used in the product 60

B Further support 68

Installation SPIDER PL

Release

09/2018 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 45.

Installation site requirements

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Operate the device at the specified ambient temperature (temperature

of the ambient air at a distance of 2 inches (5 cm) from the device) and

at the specified relative humidity exclusively.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Install the device in a fire enclosure according to EN 60950-1.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

6Installation SPIDER PL

Release

09/2018

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 45.

Mount the device in the vertical position.

At ambient air temperatures > 140 °F (+60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

Requirements for connecting the signal contact

Before connecting the signal contact, always verify that the requirements

listed are complied with.

Requirements for connecting the supply voltage

Before connecting the supply voltage, always verify that the requirements

listed are complied with.

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Table 1: Requirements for connecting electrical wires

The following requirements apply without restrictions:

The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 45.

Table 2: Requirements for connecting the signal contact

Installation SPIDER PL

Release

09/2018 7

National and international safety regulations

Verify that the electrical installation meets locally or nationally applicable

safety regulations.

Prerequisites:

All of the following requirements are complied with:

The supply voltage corresponds to the voltage specified on the type plate

of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly identified.

So in the case of an emergency, it is clear which disconnecting device

belongs to which power supply cable.

The power supply cable is suitable for the voltage, the current and the

physical load. Hirschmann recommends a wire diameter of 0.5 mm² to

0.75 mm² (AWG20 up to AWG18).

The following requirements apply alternatively:

Relevant when the device is supplied via 1 voltage input:

Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

The power supply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the power

supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 45.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 45.

Table 3: Requirements for connecting the supply voltage

8Installation SPIDER PL

Release

09/2018

Relevant for use in explosion hazard areas (Hazardous

Locations, Class I, Division 2)



 

  

2UGLQDU\/RFDWLRQ

1RQ+D]DUGRXV$UHD

1RQ([SORVLYH$WPRVSKHUH

([SORVLYH$WPRVSKHUH&ODVV,

LYLVLRQ*URXSV$%& 

+D]DUGRXV/RFDWLRQ

)RU8VHLQ+D]DUGRXV/RFDWLRQV&ODVV, LYLVLRQ*URXSV$%& 









 



:$51,1*±(;3/26,21+$=$5 ±68%67,787,212)$1<&20321(1760$<

,03$,568,7$%,/,7<)25+$=$5 286/2&$7,21625(;3/26,9(

$70263+(5(6

:$51,1*±(;3/26,21+$=$5 ± 2127 ,6&211(&7(48,30(1781/(66

32:(5+$6%((16:,7&+( 2))257+($5($,6.12:172%(

121+$=$5 286

86%FRQQHFWLRQ

























5HOD\FRQWDFWV



































Installation SPIDER PL

Release

09/2018 9

 

  



















7DEOH

 



















 

 





10 Installation SPIDER PL

Release

09/2018

ATEX directive 2014/34/EU – specific regulations for safe

operation

Relevant for SPIDER PL devices labeled with an ATEX certificate number

when operating in explosive gas atmospheres according to ATEX

Directive 2014/34/EU, the following applies:

Make sure that the device has the following label:

DEKRA 16ATEX0108X

The modules shall be installed in a suitable enclosure in accordance

with EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

Provisions shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 119 V.

Connectors shall be connected or disconnected exclusively in dead-

voltage state.

The USB port shall remain disconnected.

IECEx – Certification Scheme for Explosive Atmospheres

For SPIDER PL devices labeled with an IECEx certificate number, the

following applies:

Make sure that the device has the following label:

IECEx DEK 16.0064X

The modules shall be installed in a suitable enclosure in accordance

with EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

Provisions shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 119 V.

Connectors shall be connected or disconnected exclusively in dead-

voltage state.

The USB port shall remain disconnected.

Tabla de contenidos

Otros manuales de Cambiar de Hirschmann

Hirschmann

Hirschmann Power MICE Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8M Series Manual de usuario

Hirschmann

Hirschmann BRS20-0400 Series Manual de usuario

Hirschmann

Hirschmann MACH 100 Manual de usuario

Hirschmann

Hirschmann RH1-TP/FL Manual

Hirschmann

Hirschmann MACH 4000 Series Manual de usuario

Hirschmann

Hirschmann RH1-TP Manual

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann LRS Series Manual de usuario

Hirschmann

Hirschmann MACH102 Series Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8M-8PoE Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann Dragon PTN Manual de usuario

Hirschmann

Hirschmann Octopus II Manual de usuario

Hirschmann

Hirschmann OCTOPUS OS20 Manual de usuario

Hirschmann

Hirschmann RSPM20-4Z64Z6 Series Manual de usuario

Hirschmann

Hirschmann RSP 25 Manual de usuario

Hirschmann

Hirschmann OCTOPUS OS20 Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann SPIDER 8TX-PRO Manual de usuario

Hirschmann

Hirschmann MACH104-20TX-F Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario