Hirschmann RSP 20 Manual de usuario

Installation RSP 20/25/30/35

Release

08/2014

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch Power

RSP 20/25/30/35

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation RSP 20/25/30/35 039 792-001-08-0814 - 07.08.2014

Installation RSP 20/25/30/35

Release

08/2014 3

Contents

Safety instructions 5

About this manual 11

Key 11

1 Description 12

1.1 General description 12

1.2 Device name and product code 13

1.3 Combination options 16

1.4 Device views 17

1.4.1 Front view 17

1.4.2 Rear view 18

1.5 Power supply 18

1.5.1 Working voltage characteristic value K9 18

1.5.2 Working voltage with the characteristic value KK 18

1.5.3 Working voltage characteristic value CC 19

1.6 Ethernet ports 19

1.6.1 10/100 Mbit/s twisted pair port 19

1.6.2 100/1000 Mbit/s twisted pair port (optional) 20

1.6.3 100 Mbit/s F/O port 20

1.6.4 100/1000 Mbit/s F/O port (optional) 20

1.7 Display elements 21

1.7.1 Device state 21

1.7.2 Port state 22

1.8 Management interfaces 23

1.8.1 V.24 interface (external management) 23

1.8.2 SD card interface 23

1.9 Signal contact 24

2 Installation 25

2.1 Checking the package contents 25

2.2 Installing the SD card (optional) 25

2.3 Installing and grounding the device 26

2.3.1 Installing the device onto the DIN rail 26

2.3.2 Grounding the device 27

2.4 Installing an SFP transceiver (optional) 28

2.5 Connecting the terminal blocks 28

4Installation RSP 20/25/30/35

Release

08/2014

2.5.1 Working voltage characteristic value K9 29

2.5.2 Working voltage with the characteristic value KK 30

2.5.3 Working voltage characteristic value CC 31

2.5.4 Signal contact 32

2.6 Operating the device 32

2.7 Connecting data cables 33

2.8 Filling out the inscription label 33

3 Making basic settings 34

4 Upgrading Software 35

5 Monitoring the ambient air temperature 36

6 Maintenance and service 37

7Disassembly 38

7.1 Removing the device 38

7.2 Removing an SFP transceiver (optional) 39

8 Technical data 40

A Further Support 51

Installation RSP 20/25/30/35

Release

08/2014 5

Safety instructions

General safety instructions

You operate this device with electricity. The proper and safe operation of

this device depends on proper handling during transportation, proper

storage and assembly, and conscientious operation and maintenance

procedures. Improper use of this device is associated with the risk of

personal injury or property damage.

Read this documentation as well as the safety instructions and warn-

ings before connecting any cables.

Never start operation with damaged components.

The device does not contain any service components. If the device is

not functioning correctly, or if it is damaged, turn off the power supply

and return the device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 40.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RSP 20/25/30/35

Release

08/2014

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Working voltage

The working voltage is connected to the chassis through protective

elements exclusively.

Connect only a working voltage that corresponds to the type plate of

your device.

Only for device variants featuring working voltage with the character-

istic value K9 or KK:

See “Device name and product code” on page 13.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly iden-

tified. So in the case of an emergency, it is clear which discon-

necting device belongs to which power supply cable.

The electrical wires are voltage-free.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential. Otherwise, a fuse is

also located in the neutral conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

Supply with AC voltage:

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the working voltage input.

Installation RSP 20/25/30/35

Release

08/2014 7

Supply with DC voltage:

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the working voltage input.

The cross-section of the protective conductor is the same size as

or bigger than the cross-section of the power supply cables.

The power supply cables used are permitted for the temperature

range required by the application case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires only if all the above safety require-

ments are fulfilled.

Solely for device variants with the characteristic value CC for the

working voltage:

See “Device name and product code” on page 13.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

The power supply is Class 2 compliant.

The power supply conforms to overvoltage category I or II.

The working voltage inputs are designed for operation with safety

extra-low voltage. Connect only SELV circuits with voltage restric-

tions in line with IEC/EN 60950-1 to the working voltage connec-

tions.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly iden-

tified. So in the case of an emergency, it is clear which discon-

necting device belongs to which power supply cable.

The electrical wires are voltage-free.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the working voltage input.

The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

8Installation RSP 20/25/30/35

Release

08/2014

The power supply cables used are permitted for the temperature

range required by the application case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires only if all the above safety require-

ments are fulfilled.

Internal fuses are triggered solely in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

working voltage and return the device to the plant for inspection.

For operating voltage connections with a protective conductor connec-

tion: connect the protective conductor before connecting the conduc-

tors for the operating voltage.

Only switch on the operating voltage for the device when the following

requirements are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the operating supply are connected

Signal contact

For the signal contact to be connected, make sure the following require-

ments are met:

The device is grounded.

The signal contact connection wires are voltage-free.

The connected voltage is limited by a current limitation device or a

fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 40.

Start connecting the signal contact solely if all the above requirements are

fulfilled.

Installation site requirements

Install the device in a fire protected enclosure according to

EN 60950-1.

Only for device variants featuring working voltage with the character-

istic value K9 or KK:

See “Device name and product code” on page 13.

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

Installation RSP 20/25/30/35

Release

08/2014 9

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

Install the device in the vertical position.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The product can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Reliability: EN 60950-1

You find more information on technical and industry standards here:

“Technical data” on page 40

Device variant Directive

All variants 2004/108/EC (EMC)

Directive of the European Parliament and the council for stan-

dardizing the regulations of member states with regard to elec-

tromagnetic compatibility.

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the

restriction of the use of certain hazardous substances in elec-

trical and electronic equipment.

Only for device variants

featuring working voltage with

the characteristic value K9 or

KK:

2006/95/EC

Directive of the European Parliament and the council for stan-

dardizing the regulations of member states with regard to elec-

trical equipment to be used within specific voltage ranges.

10 Installation RSP 20/25/30/35

Release

08/2014

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take appro-

priate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

LED or laser components

LED or LASER components according to IEC 60825-1 (2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the require-

ments of a class A digital device in line with part 15 of the FCC regula-

tions.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this oper-

ating manual, it can cause radio transmission interference. The use of this

device in a residential area can also cause interference, and in this case

the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Tabla de contenidos

Otros manuales de Cambiar de Hirschmann

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann GECKO Manual de usuario

Hirschmann

Hirschmann MACH1040 Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8TX-EEC Manual de usuario

Hirschmann

Hirschmann MACH104-20TX-F Series Manual de usuario

Hirschmann

Hirschmann BATOne Manual de usuario

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann RSPM20-4Z64Z6 Series Manual de usuario

Hirschmann

Hirschmann RH1-TP Manual

Hirschmann

Hirschmann MACH4000 Series Manual de usuario

Hirschmann

Hirschmann RSPL 20 Manual de usuario

Hirschmann

Hirschmann MSM20 Manual de usuario

Hirschmann

Hirschmann PowerLION-24TP Manual de usuario

Hirschmann

Hirschmann RH1-TP/FL Manual

Hirschmann

Hirschmann MACH4000 Series Manual de usuario

Hirschmann

Hirschmann PAT TRS 05 / PATB3 Guía del usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8M Series Manual de usuario

Hirschmann

Hirschmann LRS Series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann GigaLION-24TP Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8M Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario