Hirschmann PowerMICE MS4128 Manual de usuario

PowerMICE

Document No.: 039654005 Release

04/2014

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Switch

PowerMICE

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Document No.: 039654005 PowerMICE –4.4.14

PowerMICE

Release

04/2014 3

Contents

Safety instructions 5

About this Manual 13

Legend 13

1 Device description 14

1.1 Description of the modules 15

1.1.1 PowerMICE basic module MS4128 16

1.1.2 Media modules 18

1.1.3 MB-2T expansion module 22

1.1.4 SFP modules 23

2 Assembly and start-up 24

2.1 Overview of installation 24

2.2 Installing the device 25

2.2.1 Unpacking and checking 25

2.2.2 Installing the media modules 25

2.2.3 Filling out and attaching labels 25

2.2.4 Installing the SFP modules 26

2.2.5 Adjusting DIP switch settings on basic module 27

2.2.6 Adjusting the DIP switch settings on the

MM20-A8A89999SAHH media module 28

2.2.7 Connecting the MM22-T1T1T1T1 PoE media module 28

2.2.8 Connecting the terminal blocks for supply voltage and

signal contact 30

2.2.9 Installing the terminal blocks; start-up procedure 31

2.2.10 Installing the device on the DIN rail, grounding 31

2.2.11 Connecting the data lines 32

2.2.12 Installing the MB-2T expansion module 35

2.2.13 Defining the meaning of the display LEDs 36

2.3 Display elements 36

2.4 Basic set-up 40

2.5 Maintenance 42

2.6 Disassembly 43

3 Technical data 44

A Further Support 57

4PowerMICE

Release

04/2014

PowerMICE

Release

04/2014 5

Safety instructions

This documentation contains instructions which must be observed to ensure

your own personal safety and to avoid damage to devices and machinery.

Important Information

Notice: Read these instructions carefully, and look at the equipment to

become familiar with the device before trying to install, operate, or

maintain it. The following special messages may appear throughout this

documentation or on the equipment to warn of potential hazards or to call

attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a Danger or Warning safety label

indicates that an electrical hazard exists, which will result in

personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow

this symbol to avoid possible injury or death.

Note: A note contains important information on the product, on how to

manage the product, or on the respective section of the documentation to

which your special attention is being drawn.

DANGER

DANGER indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

can result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided,

can result in minor or moderate injury.

6PowerMICE

Release

04/2014

Certified usage

The device may only be employed for the purposes described in the

catalog and technical description, and only in conjunction with external

devices and components recommended or

approved by the manufacturer. The product can only be operated cor-

rectly and safely if it is transported, stored, installed and assembled pro-

perly and correctly. Furthermore, it must be operated and serviced

carefully.

Supply voltage

For safety reasons the devices have been designed to operate at low

voltages. Thus, they may only be connected to the supply voltage

connections and to the signal contact with SELV circuits with the voltage

restrictions in accordance with IEC/EN 60950-1.

The supply voltage is electrically isolated from the housing.

Note: Only the PoE media module MM22-T1T1T1T1 has an external

power supply.

Use undamaged parts.

Relevant for North America:

The device may only be connected to a supply voltage of class 2 that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

For using the device in areas with a risk of gas explosion according to

directive 94/9/EC (ATEX):

Make sure that the device carries the following device label:

II 3G (... followed by additional specifications).

Observe the clause "Special Conditions for Safe Use ..." on the

following pages.

PowerMICE

Release

04/2014 7

Relay

Ordinary Location,

Non-Hazardous Area,

Non-Explosive Atmosphere

WARNING!

The USB connection and the V.24 Interface connection are for

temporary connection only, for maintenance use. Do not use,

connect or disconnect unless the area is known to be non-hazar-

dous. Connection or disconnection in an explosive atmosphere

could result in an explosion!

Power Supply range P1, P2 (redundant)

18 – 32 VDC

4.5 – 2.5 A

Relay contacts:

The relays are “Sealed Devices”.

THE RELAY TERMINALS ARE DEPENDENT UPON THE

FOLLOWING PARAMETERS - max. values:

Uin Iin

30 V 90 mA

Zone 2, IIC

Explosive Atmosphere

The earth conductor must be at least the

same wire size (mm² or AWG) as the supply

conductors.

Page 1/2

Special Conditions for Safe Use

under Directive 94/9/EC, ATEX

Applied Standards: EN 60079-0: 2009,

EN 60079-15: 2010

z-section sheet

8PowerMICE

Release

04/2014

Ambient temperature range “Ta: 0°C … + 60°C” ; Temperature Code “T4”.

The modules shall be installed in a suitable IP54 enclosure - with tool removable cover - in

accordance with EN 60079-15, taking into account the environmental conditions under which

the equipment will be used.

The power supply plugs P1 and P2 have to be secured by the supplied z-section sheet

and M2.5 screw inclusive tooth washer.

Provisions shall be made to prevent the rated voltage from being exceeded by

transient disturbances of more than 119 V.

When the temperature under rated conditions exceeds 70 °C at the cable or conduit entry point,

or 80 °C at the branching point of the conductors, the temperature specification of the selected

cable shall be in compliance with the actual measured temperature values.

DO NOT OPEN WHEN ENERGIZED.

Manufactured in 72654 Neckartenzlingen, Germany,

by Hirschmann Automation and Control GmbH

DOM: ww/yyyy (Date Of Manufacture: w - week, y - year – Refer to the device label.)

The Use in Hazardous Locations with explosive atmospheres is only allowed for MS4128-xxx or

HS600x model no´s. which are individually labelled

“ II 3G” and “Ex nA IIC T4 Gc”

Page 2/2

Special Conditions for Safe Use

under Directive 94/9/EC, ATEX

PowerMICE

Release

04/2014 9

Shielded ground

The shielded ground wire of the twisted pairs lines is connected to the

front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shield braiding.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

WARNING

ELECTRIC SHOCK

Never insert any pointed objects (small screwdrivers, wires, etc.) into the

product!

Never insert sharp objects (small screwdrivers, wires, etc.) into the

connection terminals for the supply voltage or the signal contact, and do not

touch the terminals!

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

CAUTION

EQUIPMENT OVERHEATING

When installing the device, make sure any ventilation slots remain free.

Maintain a clearance of at least 10 cm (3.94 in).

Failure to follow these instructions can result in injury or equipment

damage.

10 PowerMICE

Release

04/2014

The lower panel of the device is grounded by means of the DIN rail and

optionally by means of the separate ground screw.

The switch basic module forms an inseparable unity. By removing the

display and connecting parts, you risk the damage of the switch basic

module.

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

The ventilation slots must not be covered to promote free air

circulation.

The clearance between the ventilation slots of the housing and other

objects must be at least 10 cm (3.94 in).

The device has to be mounted in an upright position (see fig. 13).

If installed in a living area or office environment, the device must be

operated exclusively in switch cabinets with fire protection

characteristics in accordance with EN 60950-1.

Environment

The device may only be operated at the specified surrounding air

temperature (temperature of the surrounding air at a distance of up to

5 cm (1.97 in) from the device) and relative air humidity specified in the

technical data.

Install the device in a location where the climatic threshold values

specified in the technical data will be observed.

Use the device only in an environment within the pollution degree

specified in the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

Electricity is used to operate this equipment. Comply with every detail of

the safety requirements specified in the operating instructions regarding

the voltages to apply.

See “Supply voltage” on page 6.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Hirschmann

Hirschmann

Hirschmann BATOne Manual de usuario

Hirschmann

Hirschmann Dragon PTN Manual de usuario

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann GREYHOUND GMM42 Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann PowerLION-24TP Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann PAT TRS 05 / PATB3 Guía del usuario

Hirschmann

Hirschmann PowerMICE Manual de usuario

Hirschmann

Hirschmann SPIDER 5TX Manual

Hirschmann

Hirschmann OCTOPUS 8M-8PoE Manual de usuario

Hirschmann

Hirschmann RSPL 20 Manual de usuario

Hirschmann

Hirschmann RSP 20 Manual de usuario

Hirschmann

Hirschmann LRS Series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann RS2-5TX/FX Manual

Hirschmann

Hirschmann OCTOPUS OS20 Manual de usuario

Hirschmann

Hirschmann GRS103 Series Manual de usuario

Hirschmann

Hirschmann SPIDER 5TX Manual

Hirschmann

Hirschmann MACH104-20TX-F Series Manual de usuario

Hirschmann

Hirschmann MACH102 Series Manual de usuario

Hirschmann

Hirschmann CS30 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario