Hirschmann MSP30 Manual de usuario

Installation MSP30/32

Release

07/2014

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

MICE Switch Power

MSP30/32

MSP30/MSP32-0804... MSP30/MSP32-1604...

MSP30/MSP32-2404...

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

MSP30/32 040 014-001-04-0714 - 27.8.14

Installation MSP30/32

Release

07/2014 3

Contents

Safety instructions 5

About this manual 15

Key 15

1 Description 16

1.1 General device description 16

1.2 Device name and product code 17

1.3 Combination options 21

1.4 Device views 22

1.4.1 Front view 22

1.4.2 View from below 23

1.4.3 View from above 24

1.5 Number of ports and connections 25

1.6 Power supply 27

1.6.1 Working voltage with the characteristic value C 27

1.6.2 Working voltage with the characteristic value P 27

1.7 Display elements 27

1.7.1 Device state 27

1.7.2 Digital input 28

1.8 Management interfaces 29

1.8.1 V.24 interface (external management) 29

1.8.2 SD card interface 30

1.8.3 USB interface 30

1.9 Input/output interfaces 31

1.9.1 Signal contact 31

1.9.2 Digital input 31

2 Installation 32

2.1 Checking the package contents 32

2.2 Installing the SD card (optional) 32

2.3 Installing and grounding the device 33

2.3.1 Installing the device onto the DIN rail 33

2.3.2 Grounding the device 34

2.4 Connecting the terminal blocks 35

2.4.1 Working voltage with the characteristic value C 35

2.4.2 Working voltage with the characteristic value P 36

4Installation MSP30/32

Release

07/2014

2.4.3 Signal contact 37

2.5 Connecting the ferrite 37

2.6 Installing terminal blocks, switching on the working voltage 38

2.7 Installing media modules 39

3 Basic Settings 40

4 Upgrading Software 41

5 Maintenance and service 42

6Disassembly 43

6.1 Removing a media module 43

6.2 Removing the device 44

7 Technical data 45

A Further Support 57

Installation MSP30/32

Release

07/2014 5

Safety instructions

General safety instructions

You operate this device with electricity. The proper and safe operation of

this device depends on proper handling during transportation, proper

storage and assembly, and conscientious operation and maintenance

procedures. Improper use of this device is associated with the risk of

personal injury or property damage.

Read this documentation as well as the safety instructions and warn-

ings before connecting any cables.

Never start operation with damaged components.

The device does not contain any service components. If the device is

not functioning correctly, or if it is damaged, turn off the power supply

and return the device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation MSP30/32

Release

07/2014

Intended usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 45.

Connect to the product only components suitable for the requirements

of the specific application case.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Working voltage

Connect only a working voltage that corresponds to the type plate of

your device.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly iden-

tified. So in the case of an emergency, it is clear which discon-

necting device belongs to which power supply cable.

The disconnecting device is clearly identified so that in the case of

an emergency, it is clear which disconnecting device belongs to

which line.

The electrical wires are voltage-free.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

Regarding the properties of this fuse: See “General technical data”

on page 45.

A fuse suitable for DC voltage is located in the minus conductor of

the supply voltage, if this is not grounded.

Regarding the properties of this fuse: See “General technical data”

on page 45.

The wire diameter of the supply voltage at the input is at least 1

mm² (North America AWG16).

Installation MSP30/32

Release

07/2014 7

The power supply cables used are permitted for the temperature

range required by the application case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires only if all the above safety require-

ments are fulfilled.

Use undamaged parts.

Internal fuses are triggered solely in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

working voltage and return the device to the plant for inspection.

Only switch on the operating voltage for the device when the following

requirements are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the operating supply are connected

Note: The working voltage is connected to the chassis through protective

elements exclusively.

Installation site requirements

Verify that there is at least 4 in (10 cm) of space above and below the

device.

Verify that there is at least 0.8 in (2 cm) of space on the right and left

sides of the device.

Install the device at ambient temperatures greater than 113 °F (45 °C)

in “restricted access locations” based on EN 60950-1 exclusively.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

The switch basic module is an inseparable unit. The switch basic

module may be damaged by detachment of the display and connec-

tion part.

Keep the ventilation slits free to ensure good air circulation.

Make sure there is at least 3.94 inches (10 cm) of space in front of the

ventilation slits of the housing.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

inside of the device.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

connection terminals for the supply voltage or the signal contact, and

do not touch the terminals!

If you are operating the device in a living area or office environment,

only operate it in switch cabinets with fire protection characteristics in

accordance with EN 60950-1.

8Installation MSP30/32

Release

07/2014

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

LED or laser components

LED or LASER components according to IEC 60825-1 (2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2004/108/EC (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic compati-

bility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Reliability: EN 60950-1

You find more information on technical and industry standards here:

“Technical data” on page 45.

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take appro-

priate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Installation MSP30/32

Release

07/2014 9

Relevant for Use as Industrial Control Equipment

(according to the Standards UL508 / CSA C22.2 No. 142-

1987)

When using the MSP30/32 devices as industrial control equipment the

following restrictions apply:

Max. surrounding air temperature: +60 °C

(... to apply for operating temperature characteristic values S, T or E)

Use Copper Conductors only.

Temperature rating of field installed conductors:

Use 75 °C conductors only.

For use in Polution Degree 2 Environment only.

Digital Output - Relay (Fault): max. 30 V DC, 1 A, resistive load.

10 Installation MSP30/32

Release

07/2014

Relevant for Use in Hazardous Locations Class I Div. 2

Groups A, B ,C and D (according to the Standards

ANSI/ISA12.12.01-2013 / CSA C22.2 No.213-M1987)

This equipment is suitable for use in Class I, Division 2, Groups A, B ,C,

D– OR non-hazardous locations, if labeled "FOR USE IN HAZARDOUS

LOCATIONS".

Additional to the restrictions refering UL508 the following restriction-

sapply:

Ta: -40°F ... +140°F (-40°C ... +60°C), Temperature Code: T4

for temperature range characteristic value T and E

Ta: +32°F ... +140°F (0°C ... +60°C), Temperature Code: T4

for temperature range characteristic value S.

WARNING - EXPLOSION HAZARD - Do not disconnect equipment

unless power has been removed or the area is known to be non-

hazardous.

WARNING - EXPLOSION HAZARD - Substitution of any compo-

nentsmay impair suitability for Class I, Division 2.

- For installation and use of the MSP- modules the Control Drawing

No.000172843DNR is to apply - see the next two pages.

- The SD card has to be secured with the knurled thump-screw. Do

not connect or disconnect the SD card unless area is known to be

non-hazardous. Connection or disconnection in an explosive atmo-

sphere could result in an explosion.

Note: For information about the position on the device see “View from

above” on page 24.

- For installation and use of the MSM20/24/40/42 Media Modules-

refer to the document "USER MANUAL Installation" document to the

Media Modules MSM20/24/40/42.

Otros manuales para MSP30

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Hirschmann

Hirschmann

Hirschmann MACH104-20TX-F Series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann Octopus II Manual de usuario

Hirschmann

Hirschmann OCTOPUS 8M Series Manual de usuario

Hirschmann

Hirschmann RSPL 20 Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann LRS Series Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann BXS Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann MSP30 Manual de usuario

Hirschmann

Hirschmann RS20 series Manual de usuario

Hirschmann

Hirschmann ETHERNET IP67 Instrucciones de funcionamiento e instalación

Hirschmann

Hirschmann Power MICE Manual de usuario

Hirschmann

Hirschmann MACH4000 Series Manual de usuario

Hirschmann

Hirschmann OCTOPUS OS20 Manual de usuario

Hirschmann

Hirschmann PAT TRS 05 / PATB3 Guía del usuario

Hirschmann

Hirschmann SPIDER PL Manual de usuario

Hirschmann

Hirschmann Dragon PTN Manual de usuario

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann GREYHOUND GMM42 Manual de usuario

Hirschmann

Hirschmann RH1-TP Manual

Hirschmann

Hirschmann GREYHOUND GRS1020 Manual de usuario

Hirschmann

Hirschmann RS2-4R Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario