HIK VISION TurboHD H0T Series Manual de usuario
UM DS-2CE56H0T-ITxF 042618NA 1
• DS-2CE56H0T-IT3F
• DS-2CE56H0T-ITMF
TurboHD
H0T Series Turret Camera
User Manual
Thank you or purchasing our product. I there are
any questions or requests, do not hesitate to contact
the dealer.
This manual applies to the models below:
Hikvision USA Inc., 18639 Railroad St., City o
Industry, CA 91748, USA • Hikvision Canada, 4848 rue
Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: +1-909-895-0400 • Toll Free in USA: +1-
866-200-6690 • E-Mail: [email protected] •
www.hikvision.com
COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital
Technology Co., Ltd. ALL RIGHTS RESERVED.
Any and all in ormation, including, among others,
wordings, pictures, graphs are the properties o
Hangzhou Hikvision Digital Technology Co., Ltd. or its
subsidiaries (hereina ter re erred to be “Hikvision”).
This user manual (hereina ter re erred to be “the
Manual”) cannot be reproduced, changed, translated,
or distributed, partially or wholly, by any means,
without the prior written permission o Hikvision.
Unless otherwise stipulated, Hikvision does not make
any warranties, guarantees or representations,
express or implied, regarding to the Manual.
This manual may contain technical or printing errors,
and the content is subject to change without notice.
Updates will be added to new versions o this
manual. We will readily improve or update the
products or procedures described in the manual.
Type
Model
Type I Camera
DS
-
2CE56H0T
-
IT3F
Type II Camera
DS
-
2CE56H0T
-
ITMF
UM DS-2CE56H0T-ITxF 042618NA 2
1reface
1.1 Regulatory Information
1.1.1 FCC Information
Please take attention that changes or modi ication
not expressly approved by the party responsible or
compliance could void the user’s authority to operate
the equipment.
FCC Compliance: This equipment has been tested and
ound to comply with the limits or a Class A digital
device, pursuant to part 15 o the FCC Rules. These
limits are designed to provide reasonable protection
against harm ul inter erence when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
requency energy and, i not installed and used in
accordance with the instruction manual, may cause
harm ul inter erence to radio communications.
Operation o this equipment in a residential area is
likely to cause harm ul inter erence, in which case the
user will be required to correct the inter erence at his
own expense.
1.1.2 FCC Conditions
This device complies with part 15 o the FCC Rules.
Operation is subject to the ollowing two conditions:
1. This device may not cause harm ul inter erence.
2. This device must accept any inter erence received,
including inter erence that may cause undesired
operation.
1.1.3 EU Conformity Statement
This product and, i applicable, the
supplied accessories too are marked with
“CE” and comply there ore with the
applicable harmonized European standards
listed under the Low Voltage Directive
2014/35/EU, the EMC Directive
2012/19/EU (WEEE Directive): Products
marked with this symbol cannot be
disposed o as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase o equivalent new
equipment, or dispose o it at designated
collection points. For more in ormation see:
www.recyclethis.in o.
2006/66/EC (Battery Directive): This
product contains a battery that cannot be
disposed o as unsorted municipal waste in
the European Union. See the product
documentation or speci ic battery
in ormation. The battery is marked with this
symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return
the battery to your supplier or to a
designated collection point. For more
in ormation see: www.recyclethis.in o.
UM DS-2CE56H0T-ITxF 042618NA 3
1.1.4 Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
1.1.5 Safety Instruction
These instructions are intended to ensure that the
user can use the product correctly to avoid danger or
property loss.
The precaution measure is divided into “Warnings”
and “Cautions.”
Warnings: Serious injury or death may occur i any o
the warnings are neglected.
Cautions: Injury or equipment damage may occur i
any o the cautions are neglected.
Warnings
Follow these
sa eguards to prevent
serious injury or death.
Cautions
Follow these
precautions to prevent
potential injury or
material damage.
1.1.6
Warnings
•In the use o the device, you must be in strict
compliance with the electrical sa ety regulations o
the nation and region.
•Input voltage should meet both the SELV (Sa ety
Extra Low Voltage) and the Limited Power Source
with 12 VDC according to the IEC60950-1 standard.
Re er to technical speci ications or detailed
in ormation.
•The camera is powered by the external DC power
supply (12 VDC, 1 A) that complies with the LPS,
and the output current o this external DC power
supply must be no more than 6 A.
•Do not connect multiple devices to one power
adapter to avoid over-heating or a ire hazard
caused by overload.
•Make sure that the plug is irmly connected to the
power socket.
•Make sure that the device is irmly ixed i wall
mounting or ceiling mounting is adopted.
•I smoke, odor, or noise rise rom the device, turn
o the power at once and unplug the power cord,
and then contact the service center.
•Never attempt to disassemble the camera by
unpro essional personal.
1.1.7
Cautions
•Do not drop the camera or subject it to physical
shock.
•Do not touch sensor modules with ingers.
UM DS-2CE56H0T-ITxF 042618NA 4
•Do not place the camera in extremely hot, cold
(the operating temperature shall be -40° to 60° C),
dusty or damp locations, and do not expose it to
high electromagnetic radiation.
•I cleaning is necessary, use a clean cloth with a bit
o ethanol, and wipe it gently.
•Do not aim the camera at the sun or extra bright
places.
•The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure
that the sensor sur ace will not be exposed to the
laser beam.
•Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty, or damp
environments.
•To avoid heat accumulation, good ventilation is
required or the operating environment.
•Keep the camera away rom liquid while in use or
non-waterproo devices.
•While in delivery, the camera shall be packed in its
original packing, or packing o the same material.
1.1.8 Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
2Introduction
2.1 roduct Features
The camera is applicable or both indoor and outdoor
conditions, and the application scenarios include
road, warehouse, underground parking lot, bar, etc..
The main eatures are as ollows:
•High per ormance CMOS sensor
•IR cut ilter with auto switch
•OSD menu with con igurable parameters
•Auto white balance
•Internal synchronization
•SMART IR mode
•3-axis adjustment
UM DS-2CE56H0T-ITxF 042618NA 5
2.2 Overview
2.2.1 Overview of Type I Camera
Figure 1 Overview o Type I Camera
Note:
To switch the video output, press and hold the switch
button until the image turns black, then release.
Cycle through available types to return to the de ault
HD-TVI output. Four kinds o video outputs are
available: TVI, AHD, CVI, and CVBS.
2.2.2 Overview of Type II Camera
Figure 2 Overview o Type II Camera
Note:
Press and hold the switch button or 5 seconds to
switch the video output. Four kinds o video outputs
are available: TVI, AHD, CVI, and CVBS.
3Installation
Before you start:
•Make sure that the device in the package is in good
condition and all the assembly parts are included.
•Make sure that all the related equipment is
powered o during the installation.
•Check the speci ication o the products or the
installation environment.
•Check whether the power supply matches your
required output to avoid damage.
•Make sure the wall is strong enough to withstand
three times the weight o the camera and mount.
UM DS-2CE56H0T-ITxF 042618NA 6
•I the wall is cement, insert expansion screws
be ore installing the camera. I the wall is wooden,
use sel -tapping screws to secure the camera.
•I the product does not work properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera or repair or maintenance
yoursel .
3.1 Installation of Type I Camera
3.1.1 Ceiling/Wall Mounting without Junction Box
Steps:
1. Disassemble the turret camera by rotating the
camera to align the notch to one o the marks, as
shown in the igure below.
Figure 3 Disassemble the Camera
2. Remove the mounting base rom the camera body
with a lat object, e.g., a coin.
3. Paste the drill template (supplied) where you want
to install the camera.
4. Drill the screw holes and the cable hole (optional)
on the ceiling/wall according to the drill template.
Figure 4 Drill Template
Note:
Drill the cable hole when using the ceiling outlet to
route the cable
.
5. Attach the mounting base to the ceiling/wall, and
secure it with the supplied screws.
UM DS-2CE56H0T-ITxF 042618NA 7
Figure 5 Attach the Mounting Base to the Ceiling
Note:
•The supplied screw package contains sel -tapping
screws, and expansion bolts.
•For a cement wall/ceiling, expansion bolts are
required to ix the camera. For a wooden
wall/ceiling, sel -tapping screws are required.
6. Route the cables through the cable hole or the side
opening.
7. Align the camera with the mounting base, and
tighten the camera on the mounting base.
Figure 6 Secure the Camera with Mounting Base
8. Connect the corresponding cables, such as power
cord, and video cable.
9. Power on the camera to check i the image on the
monitor is at an optimum angle. I not, adjust the
camera according to the igure below to get an
optimum angle.
Figure 7 3-axis Adjustment
1). Hold the camera body, and rotate enclosure
to adjust the pan position [0° to 360°].
2). Move the camera body up and down to
adjust the tilt position [0° to 75°].
3). Rotate the camera body to adjust the
rotation position [0° to 360°].
UM DS-2CE56H0T-ITxF 042618NA 8
3.1.2 Mounting with Inclined Ceiling Mount
Steps:
1. Paste the drill template (supplied) where you want
to install the camera.
2. Drill screw holes and the cable hole on the
ceiling/wall according to the supplied drill
template.
Figure 8 Drill Template
3. Disassemble the inclined ceiling mount with the
screwdriver.
4. Install the turret camera’s mounting base on the
inclined ceiling mount’s cover with three PM4
screws.
Figure 9 Install Turret Camera’s Mounting Base
5. Install the inclined ceiling mount’s body on the
ceiling/wall with our PA4 × 25 screws.
Figure 10 Fix the Inclined Base Body
UM DS-2CE56H0T-ITxF 042618NA 9
6. Combine inclined ceiling mount’s cover with its
body with supplied screws.
7. Repeat steps 6 to 9 o the 2.1.1 Ceiling/Wall
Mounting without Junction Box to complete the
installation.
Figure 11 Fix the Camera to the Inclined Base
3.2 Installation of Type II Camera
Before you start:
Both wall mounting and ceiling mounting are suitable
or the turret camera. Ceiling mounting will be taken
as an example in this section. You can re erence
ceiling mounting when wall mounting.
Steps:
1. Disassemble the turret camera by rotating the
camera to align the notch to the clip plate, as
shown below.
Figure 12 Disassemble the Camera
2. Pry the mounting base to remove the mounting
base rom the camera body.
3. Paste the drill template (supplied) where you want
to install the camera.
4. Drill the screw holes according to the drill template
and the cable hole (optional) on the ceiling.
UM DS-2CE56H0T-ITxF 042618NA 10
Figure 13 Drill Template
Note:
Drill the cable hole in the center o the drill template
i using the ceiling outlet to route the cable.
5. Secure the mounting base to the ceiling with the
supplied screws.
Figure 14 Fix the Mounting Base to the Ceiling
Note:
•The supplied screw package contains sel -tapping
screws and expansion bolts.
•For a cement wall/ceiling, expansion bolts are
required to ix the camera. For a wooden
wall/ceiling, sel -tapping screws are required.
6. Route the cables through the cable hole or the side
opening.
7. Secure the camera on the mounting base.
Otros manuales para TurboHD H0T Series
4
Este manual sirve para los siguientes modelos
2
Otros manuales de Cámara digital de HIK VISION
HIK VISION
HIK VISION DS-2CE10HFT-E Manual de usuario
HIK VISION
HIK VISION DS-2CE78D0T-IT3FS Manual de usuario
HIK VISION
HIK VISION DS-2CE19DF8T-AZE Manual de usuario
HIK VISION
HIK VISION DS-MCW40B Manual de usuario
HIK VISION
HIK VISION MV-CA003-30GC Manual de usuario
HIK VISION
HIK VISION AE-VC143T-ITS Manual de usuario
HIK VISION
HIK VISION UD00719B Manual de usuario
HIK VISION
HIK VISION PanoVu PT Series Manual de usuario
HIK VISION
HIK VISION UD01715B Manual de usuario
HIK VISION
HIK VISION Color Zoom Camera Manual de usuario
HIK VISION
HIK VISION DS-MCW407 Series Manual de usuario
HIK VISION
HIK VISION HiLook Series Manual de usuario
HIK VISION
HIK VISION DS-2CD6825G0 Manual del operador
HIK VISION
HIK VISION 2 MP Series Manual de usuario
HIK VISION
HIK VISION DS-MCW406 Manual de usuario
HIK VISION
HIK VISION DS-2CE10DF8T-F Manual de usuario
HIK VISION
HIK VISION DS-MH2311 Series Manual de usuario
HIK VISION
HIK VISION HIKMICRO CHEETAH Series Manual de usuario
HIK VISION
HIK VISION AE-VC222T-ITS Manual de usuario
HIK VISION
HIK VISION DS-PDPC12PF-EG2-WBB Manual de usuario
