HIK VISION UD02783B Manual de usuario

Vehicle-Mounted Camera

User Manual

UD02783B

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to Vehicle-Mounted Camera.

This manual may contain several technically incorrect

places or printing errors. The content is subject to change

without notice, and the updates will be added to the new

version of this manual. We will readily improve or update

the products or procedures described in the manual.

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European standards listed under

the Low Voltage Directive 2014/35/EC, the EMC Directive

2014/30/EC.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more

information see: www.recyclethis.info.

2006/66/EC (battery directive): This

product contains a battery that cannot be

disposed of as unsorted municipal waste in the European

Union. See the product documentation for specific

battery information. The battery is marked with this

symbol, which may include lettering to indicate cadmium

(Cd), lead (Pb), or mercury (Hg). For proper recycling,

return the battery to your supplier or to a designated

collection point. For more information see:

www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”

Warnings: Serious injury or death may occur if any of the

warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the product, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Refer to technical specifications for detailed

information.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with AC

24V or DC 12V according to the IEC60950-1 standard.

Refer to technical specifications for detailed

information.

Do not connect several devices to one power adapter

as adapter overload may cause over-heating or a fire

hazard.

Make sure that the plug is firmly connected to the

power socket.

When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cable, and

then please contact the service center.

If the product does not work properly, contact your

dealer or the nearest service center. Never attempt to

disassemble the camera by yourself. (We shall not

assume any responsibility for problems caused by

unauthorized repair or maintenance.)

Cautions

Make sure the power supply voltage is correct before

using the camera.

Do not drop the camera or subject it to physical shock.

Do not touch senor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and

wipe it gently. If the camera will not be used for an

extended period, replace the lens cap to protect the

sensor from dirt.

Do not aim the camera at the sun or extra bright

places. Blooming or smearing may occur otherwise

(which is not a malfunction), and affect the endurance

of sensor at the same time.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not place the camera in extremely hot, cold, dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

To avoid heat accumulation, good ventilation is

required for operating environment.

Keep the camera away from liquid while in use.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Symbol Conventions

The symbols that may be found in this document are

defined as follows.

Symbol

Description

Provides additional information to

emphasize or supplement important

points of the main text.

Indicates a potentially hazardous

situation, which if not avoided, could

result in equipment damage, data loss,

performance degradation, or

unexpected results.

Indicates a hazard with a high level of

risk, which if not avoided, will result in

death or serious injury.

Introduction1

1.1 Product Features

This series of camera adopts high performance sensor

and advanced circuit board design technology. It features

high resolution, low distortion, and low noise, etc. It is

suitable for surveillance system and image process

system.

The main features are as follows:

Low illumination, 0.1 Lux @ (F1.2, AGC ON), 0 Lux with

IR.

High performance CMOS sensor and high resolution

bring high-quality image.

Build-in microphone.

Aviation plug design.

Advanced 3-axis design meets different installation

requirements.

1.2 Overview

1.2.1 Overview of Type I Camera

The overview of type I camera is shown below.

Overview of Type I CameraFigure 1-1

Description of Type I CameraTable 1-1

NO.

Description

Suction Mounting Base

Main Body

Aviation Plug

Lens

Microphone

1.2.2 Overview of Type II Camera

The overview of Type II camera is shown below.

Overview of Type II CameraFigure 1-2

Description of Type II CameraTable 1-2

NO.

Description

Photosensitive Resistor

IR LED

Main Body

Microphone

Lens

Aviation Plug

1.2.3 Overview of Type III Camera

The overview of type III camera is shown below.

Overview of Type III CameraFigure 1-3

Description of Type III CameraTable 1-3

NO.

Description

Photosensitive Resistor

IR LED

Main Body

Lens

Microphone

Aviation Plug

1.2.4 Overview of Type IV Camera

The overview of type IV camera is shown below.

Rearview Fore view

Overview of Type IV CameraFigure 1-4

Description of Type IV CameraTable 1-4

NO.

Description

Sunction Mounting Base

Main Body

Aviation Plug

Lens

Microphone

Photosensitive Resistor

IR LED

The rearview camera of type IV camera has IR LED and it

can monitor the inside of car. The fore view camera can

monitor the outside of car.

1.3 Interfaces of Aviation Plug

Video Interface

Audio Interface

Power Supply

GND

Interfaces of Aviation PlugFigure 1-5

Installation2

Before you start:

Please make sure that the device in the package is in

good condition and all the assembly parts are

included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with your

required output to avoid damage.

Please make sure the wall is strong enough to

withstand four times the weight of the camera and

the mounting.

If the wall is the cement wall, you need to insert

expansion screws before you install the camera. If the

wall is the wooden wall, you can use self-tapping

screw to secure the camera.

If the product does not function properly, please

contact your dealer or the nearest service center. Do

not disassemble the camera for repair or maintenance

by yourself.

2.1 Installation of Type I Camera

This camera supports windshield mounting with sticker.

The installation steps are as follows.

Loosen the secure screw of the camera, asStep 1

shown in Figure 2-1.

Secure Screw

Secure ScrewFigure 2-1

Adjust the double-side tape sticker base to aStep 2

suitable installation angle.

Press the double-side tape sticker base to theStep 3

windshield.

Secure Screw

180°

Sticker

Adjust the camera angle.Step 4

Secure the camera by tightening the secureStep 5

screw.

2.2 Installation of Type II Camera

This camera supports wall mounting. Two methods are

available for wall mounting of Type II camera. The

following procedures are the wall mounting application

with screws/sticker.

Wall mounting with screws or sticker.Step 1

Attach the drill template (supplied) to the

wall.(wall mounting with screws)

37.67

18.84

Drill TemplateFigure 2-2

Attach the sticker to the base plate and align the

notches of sticker to the screw holes. (wall

mounting with sticker)

Sticker

Attach the StickerFigure 2-3

Route the cable through the cable hole. (in theStep 2

cable notch)

Cable Notch

Route CablesFigure 2-4

Fix the base plate onto the wall with screws.(wallStep 3

mounting with screws)

Install the camera onto the wall. In Figure 2-7,Step 4

part A is for wall mounting with sticker and press

the camera to the wall. Part B is for wall

mounting with screws and use screws to install

the camera.

Press

Install the CameraFigure 2-5

Make sure the enclosure is properly fixed withStep 5

the base plate.

EnclosureFigure 2-6

Insert the clips of enclosure into the slot of the base

plate.

Insert the adjustment ring into the camera toStep 6

perform the 3-axis adjustment.

Rotation Position Range

[0°~360°]

Pan Position Range

[0°~360°]

Tilt Position Range

[0°~60°]

3-axis AdjustmentFigure 2-7

Secure the camera by locking the lock catch.Step 7

2.3 Installation of Type III Camera

This camera supports in-ceiling mounting. The installation

steps are as follows.

Attach the drill template (supplied) to the ceiling.Step 1

53.2

138.6

130

Drill TemplateFigure 2-8

Loosen the fixing screw and take apart theStep 2

enclosure.

Fixing Screw

Take Apart the EnclosureFigure 2-9

Route the cable through the cable hole. (in theStep 3

cable notch)

Cable Outlet

Route CablesFigure 2-10

Fix the base plate onto the wall with screws.Step 4

Install the camera onto the ceiling.Step 5

Tabla de contenidos

Otros manuales de Cámara digital de HIK VISION

HIK VISION

HIK VISION DS-2CD2155FWD-IS Manual de usuario

HIK VISION

HIK VISION UD01715B Manual de usuario

HIK VISION

HIK VISION TandemVu SE4C Series Manual de usuario

HIK VISION

HIK VISION Ultra Series Manual de usuario

HIK VISION

HIK VISION MCH508 Manual de usuario

HIK VISION

HIK VISION DS-MCW406 Manual de usuario

HIK VISION

HIK VISION DS-2CE10DF0T-F Manual de usuario

HIK VISION

HIK VISION MV-CA003-30GC Manual de usuario

HIK VISION

HIK VISION Body Camera Manual de usuario

HIK VISION

HIK VISION DS-2CD6825G0/C-I(V)(S) Manual de usuario

HIK VISION

HIK VISION UD00719B Manual de usuario

HIK VISION

HIK VISION DS-2TD1217-6/PA Manual de usuario

HIK VISION

HIK VISION DS-2CE12DF3T-PIRXOS Manual de usuario

HIK VISION

HIK VISION DS-2CE70DF3T-PTS Manual de usuario

HIK VISION

HIK VISION AE-VC143T-ITS Manual de usuario

HIK VISION

HIK VISION Wiegand iDS-2CD7A26G0/P-IZHSY Manual de usuario

HIK VISION

HIK VISION DS-MCW405 Manual de usuario

HIK VISION

HIK VISION 2 MP Series Manual de usuario

HIK VISION

HIK VISION DS-2CE16K0T-LFS Manual de usuario

HIK VISION

HIK VISION 6825 Manual del operador

HIK VISION

HIK VISION DS-2CE19DF8T-AZE Manual de usuario

HIK VISION

HIK VISION DY7 Series Manual de usuario

HIK VISION

HIK VISION DS-2CD6825G0 Manual del operador

HIK VISION

HIK VISION E10-DS-2XS2T47G1 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario