H3C SecPath PSR300-12A2 Manual de usuario

H3C SecPath PSR300-12A2 &

PSR300-12D2 Power Modules

User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W101-20190307

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of New H3C

Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any

trademarks that may be mentioned in this document are the property

of their respective owners.

Notice

The information in this document is subject to change without notice.

All contents in this document, including statements, information, and

recommendations, are believed to be accurate, but they are

presented without warranty of any kind, express or implied. H3C shall

not be liable for technical or editorial errors or omissions contained

herein.

Documentation feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments

Contents

Overview ·················································· 1

Introduction···································································· 1

Technical specifications ··················································· 1

Views ··········································································· 2

LEDs············································································ 3

Installing and removing the power module······· 5

Safety precautions ·························································· 5

Tools············································································ 5

Installing and removing the power module ··························· 5

Installing the power module ·········································· 6

Connecting the power cord··········································· 8

Removing the power module········································10

Overview

Introduction

The PSR300-12A2 is an AC-input and DC-output power module. The

PSR300-12D2 is a DC-input and DC-output power module. They

provide a maximum output power of 300 W.

The PSR300-12A2 and PSR300-12D2 power modules have the

following features:

•Self-protected against input overcurrent, input undervoltage,

output overvoltage, output short-circuit, and overtemperature.

•Support for 1+1 redundancy and load sharing.

•Hot swappable.

Technical specifications

Table 1 Technical specifications

Item Specifications

Rated input voltage

•PSR300-12A2: 100 VAC to 240

VAC

•PSR300-12D2: –48 VDC to –60

VDC

Output voltage 12 V

Maximum output current 25 A

Maximum output power 300 W

Dimensions (H × W × D) 40.13 × 101.6 × 234.9 mm (1.58 ×

4.00 × 9.25 in)

Item Specifications

Operating temperature 0°C to 55°C (32°F to 131°F)

Operating humidity 5% RH to 95% RH, non-condensing

Views

Figure 1 PSR300-12A2

Figure 2 PSR300-12D2

(1) Power switch ("O" represents off and "—" represents on)

(2) Power receptacle (3) Spring tab

(4) Handle (5) Power output status LED

(6) Power input status LED (7) Bail clasp mounting holes

(8) Captive screw

(9) Screw holes for securing the power cord connector

LEDs

The power module uses power input and power output LEDs to

indicate the power input and output status, respectively.

Table 2 LED description

LED Status Description

Power input status

LED (AC OK or

Input)

Off No power is being input or an

input failure has occurred.

On Normal power input.

Power output status

LED (DC OK or

Output)

Off No power is being output or an

output failure has occurred.

On Normal power output.

If the power input LED is on but the output LED is off, an output issue

might have occurred. To resolve the issue:

1. Turn off the power switch on the power module and reconnect

the power cord.

This operation resolves the power module failure caused by an

output overvoltage, output short-circuit, or output overcurrent

condition. The power module shuts down and latches off if one

of these conditions occurs and cannot automatically restore

operation.

2. If the issue persists, the temperature might be high. Take

measures to decrease the temperature to an acceptable range.

The power module will automatically restore operation.

Installing and removing the power

module

Safety precautions

To avoid possible bodily injury and power module and device

damage, follow these safety precautions:

•When installing and removing the power module, always wear

an ESD wrist strap and make sure it makes good skin contact.

•Make sure the voltage of the power source is as required by the

power module, and the output voltage of the power module is as

required by the device.

•To avoid bodily injury, do not touch any bare wire or terminal.

•Do not place the power module in a wet location, and prevent

liquid from flowing into the power module.

•To avoid power module damage, do not open the power module.

If the internal wires or units are faulty, contact H3C Support.

Tools

When installing and removing a power module and power cord, you

must wear an ESD wrist strap. Prepare it yourself.

Installing and removing the power module

The installation and removal procedures are similar for the

PSR300-12A2 and PSR300-12D2 power modules. The following

procedures use the PSR300-12D2 power module as an example.

Installing the power module

CAUTION:

To avoid bodily injury and device damage, strictly follow the

procedure in Figure 3 to install the power module.

Figure 3 Power module installation procedure

To install the power module:

1. Wear an ESD wrist strap and make sure the strap makes good

skin contact and is reliably grounded.

2. Unpack the power module and make sure the power module

model is as required.

Keep the power module package secure for future use.

3. As shown in Figure 4, correctly orient the power module (with

the lettering on it upwards). Grasping the module handle with

one hand and supporting the module bottom with the other,

push the module slowly into the slot along the guide rails. Make

sure the power module has good contact with the backplane

connectors.

The power module and power module slot are designed to

prevent disorientation and misalignment. If you cannot insert the

power module smoothly into the slot, the orientation might be

wrong or the power module is not aligned correctly with the slot.

Pull out the power module, reorient the power module or realign

it with the slot, and insert it again.

4. When the power module is fully seated in the slot, fasten the

captive screw on the power module.

Figure 4 Installing the power module

Otros manuales para SecPath PSR300-12A2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de H3C

H3C

H3C LSQM1CGS2QSA0 Manual de usuario

H3C

H3C PSR2400-54A Manual de usuario

H3C

H3C SR6600 SPE-FWM Manual de usuario

H3C

H3C SecPath M9000 NSQM1MBFEA0 Manual de usuario

H3C

H3C PSR1600B-12A-B Manual de usuario

H3C

H3C PSR250-12A1 Manual de usuario

H3C

H3C S9500 LSB1FW2A0 Manual de lista de piezas

H3C

H3C PSR1800-56A Manual de usuario

H3C

H3C SFP-GE-SX-MM850-A Manual de usuario

H3C

H3C S9500 LSB1LB1A0 Manual de usuario

H3C

H3C NSQ1FAB04B0 Manual de usuario

H3C

H3C LSQ1LBSC0 Manual de usuario

H3C

H3C LSVM1S9810FAN Manual de usuario

H3C

H3C SecPath M9000 NSQM1CGQ20 Manual de usuario

H3C

H3C LSVM152SCFAN Manual de usuario

H3C

H3C PSR3000-54A Manual de usuario

H3C

H3C S9500E Series Manual de lista de piezas

H3C

H3C LSQM1SDNB0 Manual de usuario

H3C

H3C EWPA1PCID Manual de usuario

H3C

H3C PSR250-12A Manual de usuario

H3C

H3C R6900-FAN Manual de usuario

H3C

H3C PSR360-56A Manual de usuario

H3C

H3C LSWM18CQ Manual de usuario

H3C

H3C SecPath NSQ1FAB04B0 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario