H3C SecPath NSQ1FAB08D0 Manual de usuario

Manual version: 6PW107-20210319 BOM: 3123A0R2

H3C SecPath NSQ1FAB08D0 switching fabric module

1 Module view

The NSQ1FAB08D0 switching fabric module uses product code NSQM1FAB08D0.

Figure 1 NSQ1FAB08D0 switching fabric module

2 Specifications

Figure 2 Front panel

(1) Console port (CONSOLE) (2) Status LEDs

Table 1 Module specifications

Item Specification

Dimensions (H × W × D) 40 × 426 × 298 mm (1.57 × 16.77 × 11.73 in)

Power consumption 101 W to 135 W

Weight 2.77 kg (6.11 lb)

Hot swapping Supported

Connector type RJ-45

Ports 1 × console port

Ambient temperature Operating: 0°C to 45°C (32°F to 113°F)

Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity Operating: 10% RH to 95% RH, noncondensing

Storage: 5% RH to 95% RH, noncondensing

Manual version: 6PW107-20210319 BOM: 3123A0R2

Item Specification

Compatible device models and

slots

•M9010 gateway (slots 10 to 13)

•M9010-GM gateway (slots 10 and 11)

•T9010 IPS (slots 10 to 13)

IMPORTANT:

•You can configure a maximum of two switching fabric module for an M9010-GM gateway.

•An M9010 gateway and a T9010 IPS each require a minimum of three switching fabric modules,

and slots 10 and 11 must be installed with switching fabric modules.

3 LEDs

The module provides LEDs to show its operating status.

Table 2 LED description

RUN LED ALM LED Description

Flashing (0.5 Hz) Off The switching fabric module is operating properly.

Off On The switching fabric module is faulty.

Flashing (0.5 Hz) On The temperature of the switching fabric module has exceeded the

upper or lower limit.

Off Off The switching fabric module has not started.

On Off The switching fabric module is starting up.

4 Installing and removing the module

CAUTION:

•Wear a well-grounded ESD-preventive wrist strap before you install or remove the module.

•When you install or remove the module, avoid touching the components on it.

4.1 Installing the module

1. Face the rear panel of the device.

2. Remove the filler panel from the target slot.

This example uses slot 11.

3. Place the module horizontally with the component side facing up. Open the ejector levers and

gently push the module into the slot along the guide rails, as shown by callout 1 in Figure 3.

4. Close the ejector levers. Make sure the module is in close contact with the backplane, as shown

by callout 2 in Figure 3.

5. Use a Phillips screwdriver to fasten the captive screws on the module, as shown by callout 3

in Figure 3.

Manual version: 6PW107-20210319 BOM: 3123A0R2

iii

Figure 3 Installing the module

(1) Gently push the module into the slot along the guide rails until the module is in close contact with the

backplane.

(2) Close the ejector levers.

(3) Use a Phillips screwdriver to fasten the captive screws.

(4) Installation is finished.

4.2 Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously open the ejector levers on the module to separate the module from the

backplane, and pull the module slowly out of the chassis along the guide rails.

3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component

side facing up.

If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

The information in this document is subject to change without notice.

Otros manuales de Unidad de control de H3C

H3C

H3C S12500 LST1LB1A1 Manual de usuario

H3C

H3C SecPath NSQ1FAB04B0 Manual de usuario

H3C

H3C SecPath NSQM2AC1400 Manual de usuario

H3C

H3C NSQM1FWDFGC1 Manual de usuario

H3C

H3C LSBM1WCM2A0 Manual de usuario

H3C

H3C PSR750-A Manual de usuario

H3C

H3C PSR250-12A1 Manual de usuario

H3C

H3C LSVM1S9810FAN Manual de usuario

H3C

H3C LSWM18CQ Manual de usuario

H3C

H3C LSWM116FC Manual de usuario

H3C

H3C SR6600 SPE-FWM Manual de usuario

H3C

H3C PSR3000-54A Manual de usuario

H3C

H3C SIC-4G-LTE-M Instrucciones de funcionamiento y mantenimiento

H3C

H3C SecPath M9000 NSQM1CGQ20 Manual de usuario

H3C

H3C SR6600 SPE-FWM-200 Manual de usuario

H3C

H3C NSQ1FAB04B0 Manual de usuario

H3C

H3C S9500 LSB1FW2A0 Manual de lista de piezas

H3C

H3C SecPath M9000 NSQM1MBFEA0 Manual de usuario

H3C

H3C SecPath M9000-AI NSQM5AIASKA1 Manual de usuario

H3C

H3C S9500 LSB1LB1A0 Manual de usuario

H3C

H3C SecBlade Manual de usuario

H3C

H3C SecPath PSR300-12A2 Manual de usuario

H3C

H3C LSQM1CGS2QSA0 Manual de usuario

H3C

H3C LSVM2106SFAN Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario