Fujitsu Citrix XenServer Manual de usuario
FUJITSU Storage
ETERNUS DX
Configuration Guide -Server Connection-
(SAS) for Citrix® XenServer®
P3AM-8552-06ENZ0
This page is intentionally left blank.
Preface
This manual briefly explains the operations that need to be performed by the user in order to connect an
ETERNUS DX to a server running Citrix® XenServer® via a SAS interface.
This manual should be used in conjunction with any other applicable user manuals, such as those for the
ETERNUS DX, servers, OS, SAS cards, and drivers.
Refer to "Configuration Guide -Server Connection- Notations" for the notations used in this manual such as
product trademarks and product names. For storage systems that are supported by the OS, refer to the Server
Support Matrix of the ETERNUS DX.
6th Edition
September 2017
The Contents and Structure of this Manual
This manual is composed of the following eight chapters.
•"Chapter 1 Workflow" (page 7)
This chapter describes how to connect the ETERNUS DX storage systems to a server running Citrix® XenServ-
er®.
•"Chapter 2 Checking the Server Environment" (page 9)
This chapter describes which servers can be connected to ETERNUS DX storage systems.
•"Chapter 3 Notes" (page 10)
This chapter describes issues that should be noted when connecting the ETERNUS DX storage systems and
server.
•"Chapter 4 Setting Up the ETERNUS DX" (page 12)
This chapter describes how to set up an ETERNUS DX.
•"Chapter 5 Setting Up the SAS Switches" (page 13)
This chapter describes how to set up the SAS switches.
•"Chapter 6 Installing the Driver" (page 15)
This chapter describes how to install the SAS card drivers.
•"Chapter 7 Setting Up XenServer" (page 16)
This chapter describes how to set up Citrix® XenServer®.
•"Chapter 8 SAN Boot" (page 21)
This chapter provides notes for SAN Boot.
3
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Citrix XenServer Terminology
•Storage Repository (SR)
A container where virtual disk images are stored
•Virtual Disk Image (VDI)
A storage abstraction that is presented to a Virtual Machine
The fundamental unit of virtualized storage in XenServer
•Physical Block Device (PBD)
An interface between a physical server and a Storage Repository
A connector object to map a Storage Repository to a XenServer host
•Virtual Block Device (VBD)
A connector object to map between VDIs and VMs
•Virtual Machine (VM)
A virtual machine that is created on XenServer (Guest OS)
Preface
4
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Table of Contents
Chapter 1 Workflow 7
Chapter 2 Checking the Server Environment 9
2.1 Servers ........................................................................................................................................... 9
2.2 SAS Cards........................................................................................................................................ 9
2.3 Connection Compatibility of ETERNUS DX Storage Systems to XenServer Host................................ 9
2.4 Virtual Machine.............................................................................................................................. 9
Chapter 3 Notes 10
3.1 Installation Notes......................................................................................................................... 10
3.2 Operating Notes ........................................................................................................................... 10
3.3 ETERNUS DX Setup Notes.............................................................................................................. 10
3.4 Server Startup and Power Supply Control Notes............................................................................ 11
Chapter 4 Setting Up the ETERNUS DX 12
Chapter 5 Setting Up the SAS Switches 13
Chapter 6 Installing the Driver 15
6.1 For Fujitsu SAS Cards .................................................................................................................... 15
6.2 For LSI Logic SAS Cards ................................................................................................................. 15
Chapter 7 Setting Up XenServer 16
7.1 Setting Up the SAS Cards .............................................................................................................. 16
7.1.1 For Fujitsu SAS Cards...........................................................................................................................................16
7.1.2 For LSI Logic SAS Cards........................................................................................................................................16
7.2 Turning on the Devices ................................................................................................................ 16
7.3 Checking LUN Status .................................................................................................................... 17
7.4 Creating a Storage Repository ...................................................................................................... 17
7.5 Setting the Multipaths ................................................................................................................. 18
5
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Chapter 1
Workflow
This chapter describes how to connect the ETERNUS DX storage systems to a server. The workflow is shown
below.
Required Documents
•"Server Support Matrix"
•"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETERNUS DX to
be connected
•"ETERNUS Web GUI User's Guide"
•Manuals supplied with the server, SAS cards, and multipath driver
Workflow
Setting Up the ETERNUS DX
Set up the ETERNUS DX using ETERNUS Web GUI.
•Checking the setup and maintenance operations
-"Chapter 2 Checking the Server Environment" (page 9)
-"Chapter 4 Setting Up the ETERNUS DX" (page 12)
-"ETERNUS Web GUI User's Guide"
•Setting up the ETERNUS DX
-"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the
ETERNUS DX to be connected
Setting Up the SAS Switches
Set up the SAS switch.
•"Chapter 5 Setting Up the SAS Switches" (page 13)
7
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Installing the Driver
Install the appropriate driver for the SAS card being used.
•Checking the SAS card driver versions
-"Chapter 6 Installing the Driver" (page 15)
-"Server Support Matrix"
Setting Up XenServer
Set up XenServer to connect to the ETERNUS DX.
•"Chapter 7 Setting Up XenServer" (page 16)
•Setting up XenServer and SAS cards
-"7.1 Setting Up the SAS Cards" (page 16)
•Checking the SAS card driver versions
-"Server Support Matrix"
Checking the LUNs
Check whether the server recognizes the LUNs of the ETERNUS DX and set up the LUNs so that they
can be used on XenServer.
•"7.3 Checking LUN Status" (page 17)
Creating a Storage Repository
Create a Storage Repository.
•"7.4 Creating a Storage Repository" (page 17)
Setting the Multipaths
Use the XenServer multipath to perform a redundant configuration.
•"7.5 Setting the Multipaths" (page 18)
Chapter 1 Workflow
8
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Chapter 2
Checking the Server Environment
Connection to servers is possible in the following environments.
Check the "Server Support Matrix" for server environment conditions.
2.1 Servers
For supported servers, refer to "Server Support Matrix" and the following URL:
http://hcl.xensource.com/
If a logical unit (LUN) of the ETERNUS DX storage systems is used as a boot disk, refer to "Server Support
Matrix" to check the server environment.
2.2 SAS Cards
Refer to the "Server Support Matrix".
2.3 Connection Compatibility of ETERNUS DX Storage Systems to
XenServer Host
Refer to the "Server Support Matrix".
2.4 Virtual Machine
For details on the procedure and notes about installing a Virtual Machine that is supported by XenServer,
refer to the manuals that can be obtained on the following Citrix web-site:
https://support.citrix.com/en/products/xenserver
9
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Chapter 3
Notes
Note the following issues when connecting the ETERNUS DX to a server.
3.1 Installation Notes
•To ensure reliable access to ETERNUS DX storage systems, multipath configuration is recommended.
•Setting up multiple access paths between the server and the ETERNUS DX storage systems, then using the
XenServer multipath, provides improved access redundancy.
•Enable the virtualization support functions (Intel VT or AMD-V) of the server before installing XenServer.
For details on the settings, refer to the relevant manual of the server to be used.
•Install XenServer when the ETERNUS DX is not connected to the server.
•The ETERNUS Multipath Driver does not need to be installed on the XenServer Virtual Machine. The Xen-
Server multipath provides path redundancy.
•When multiple paths are used, a multipath driver must be set. If a multipath driver is not set, the XenServ-
er multipath does not perform proper load balancing for the ETERNUS DX.
•Before setting a multipath configuration, create Storage Repositories for all the LUNs that exist in the
ETERNUS DX.
3.2 Operating Notes
•If a path error occurs in a multipath configuration using XenServer, the status of the failed multipath may
not be displayed. The status is displayed again when the failed path recovers.
•When XenServer is managed and operated with XenCenter, multipath errors may not be detected properly
by XenCenter. When checking multipath status, also check the status on the XenServer host side.
3.3 ETERNUS DX Setup Notes
•Host Response must be set before the ETERNUS DX is connected to the XenServer host.
•Even if the Eco-mode of the ETERNUS DX is enabled for a multipath configuration with XenServer, disk mo-
tors may not stop according to the Eco-mode settings.
10
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Citrix® XenServer®
Copyright 2017 FUJITSU LIMITED
P3AM-8552-06ENZ0
Tabla de contenidos
Otros manuales de Almacenamiento de Fujitsu
Fujitsu
Fujitsu ETERNUS JX40 S2 Manual de usuario
Fujitsu
Fujitsu MHV2100AH Manual de usuario
Fujitsu
Fujitsu ETERNUS DX60 S3 Manual de usuario
Fujitsu
Fujitsu ETERNUS DX60 Manual de usuario
Fujitsu
Fujitsu GRANPOWER 5000 GP5-HDH461 Manual de usuario
Fujitsu
Fujitsu MHW2160BJ Manual de usuario
Fujitsu
Fujitsu MPB3021AT Manual de usuario
Fujitsu
Fujitsu Streamer DAT 160 Manual de usuario
Fujitsu
Fujitsu MHW2040BS Manual de usuario
Fujitsu
Fujitsu DYNAMO 640AI Manual de usuario
Fujitsu
Fujitsu ETERNUS DX60 Manual de usuario
Fujitsu
Fujitsu M2488 Manual de usuario
Fujitsu
Fujitsu GP5-HD9G3 Manual de usuario
Fujitsu
Fujitsu ETERNUS2000 200 Guía
Fujitsu
Fujitsu ETERNUS LT20 S2 Manual de usuario
Fujitsu
Fujitsu SLR 50 GBYTE Manual de usuario
Fujitsu
Fujitsu DynaMO 640FE Manual de usuario
Fujitsu
Fujitsu MBA3073NC Manual de usuario
Fujitsu
Fujitsu MAX3036RC SERIES Manual de usuario
Fujitsu
Fujitsu MHC2032AT Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario