Fujitsu ETERNUS DX400 series Manual de usuario

FUJITSU Storage

ETERNUS DX

Configuration Guide -Server Connection-

P3AM-3972-08ENZ0

(iSCSI) ETERNUS DX400/DX8000 series Disk Storage System Settings

This page is intentionally left blank.

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

Preface

This manual briefly explains the operations that need to be performed by the user in order to connect an

ETERNUS DX410/DX440 or an ETERNUS DX8100/DX8400/DX8700 Disk storage system to a server running

Solaris OS, HP-UX, Windows®, Linux, VMware ESX, or Oracle VM Server via an iSCSI interface.

This manual should be used in conjunction with other applicable user manuals, such as those for the ETERNUS

DX410/DX440 or ETERNUS DX8100/DX8400/DX8700 Disk storage system, server, OS, iSCSI HBAs, LAN cards,

and drivers.

Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations

used in this manual such as product trademarks and product names.

This manual references the following document:

•ETERNUSmgr User Guide

Also, note that in this manual the ETERNUS DX410/DX440, ETERNUS DX8100/DX8400/DX8700 Disk storage

systems are referred to as ETERNUS DX.

Eighth Edition

December 2014

The Contents and Structure of this Manual

This manual is composed of the following two chapters.

●Chapter 1 Workflow

This describes the workflow when setting up an ETERNUS DX.

●Chapter 2 ETERNUS DX Connection Settings

This describes the settings used when connecting an ETERNUS DX.

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

Table of Contents

Chapter 1 Workflow 6

Chapter 2 ETERNUS DX Connection Settings 8

2.1 Common Settings ................................................................................................................ 8

2.1.1 Setting the To-server Connection Type (Setting the CA Parameters) ................................................................8

2.1.2 Sense Data Conversion (Setting the Host Responses) ......................................................................................9

2.1.3 Setting the Server iSCSI Host .......................................................................................................................... 12

2.1.4 Setting the Server Accessible LUN Groups (Setting Affinity Groups) ...............................................................12

2.1.5 Creating and Allocating LUN Groups (Setting Host Affinity Groups) ............................................................... 13

2.1.6 Setting CHAP Authentication .........................................................................................................................13

2.2 OS Specific Settings ........................................................................................................... 14

2.2.1 Setting the CA Reset Groups .......................................................................................................................... 14

2.2.2 Setting the Sub System Parameters (for HP-UX only) .................................................................................... 15

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

List of Tables

Table 2.1 CA parameter settings (iSCSI port settings) ................................................................................................... 8

Table 2.2 Reservation Conflict Response for Test Unit Ready setting for Solaris OS ....................................................... 9

Table 2.3 Sense Data Conversion Pattern setting for Solaris OS .................................................................................... 9

Table 2.4 Host Specific Mode setting for HP-UX ............................................................................................................ 9

Table 2.5 Reservation Conflict Response for Test Unit Ready setting for Windows® .................................................... 10

Table 2.6 Sense Data Conversion Pattern setting for Windows® ................................................................................. 10

Table 2.7 Sense Data Conversion Pattern setting for Linux......................................................................................... 10

Table 2.8 Inquiry Standard Data Version setting for VMware ESX................................................................................ 11

Table 2.9 Sense Data Conversion setting for VMware ESX........................................................................................... 11

Table 2.10 Asymmetric/Symmetric Logical Unit Access setting for VMware ESX............................................................ 11

Table 2.11 Data Transfer Timer setting for VMware ESX................................................................................................ 11

Table 2.12 Inquiry Standard Data Version setting for VMware ESX................................................................................ 11

Table 2.13 Sense Data Conversion setting for Oracle VM Server.................................................................................... 12

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

Chapter 1

Workflow

This manual is used when performing the setup procedures described in the "Setting up the ETERNUS DX"

section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (iSCSI)" for each OS.

Workflow

Setting the CA Parameters

Set the to-server connection type.

Refer

-"2.1.1 Setting the To-server Connection Type (Setting the CA Parameters)" (page 8)

Setting the Host Responses

Set the host responses to match the connection configuration.

Refer

-"2.1.2 Sense Data Conversion (Setting the Host Responses)" (page 9)

Setting Server iSCSI

Set IP addresses, aliases, and iSCSI names for servers.

Refer

-"2.1.3 Setting the Server iSCSI Host" (page 12)

Chapter 1 Workflow

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

After completing all the required procedures in this manual, follow the procedures in "FUJITSU

Storage ETERNUS DX Configuration Guide -Server Connection- (iSCSI)" for each OS.

Setting the Affinity Groups

Set the server accessible LUN groups.

Refer

-"2.1.4 Setting the Server Accessible LUN Groups (Setting Affinity Groups)" (page 12)

Setting Host Affinity Groups

Define the relationship between the iSCSI card HBA and LUN group.

Refer

-"2.1.5 Creating and Allocating LUN Groups (Setting Host Affinity Groups)" (page 13)

When setting CHAP authentication When not setting CHAP authentication

Setting CHAP Authentication

Set CHAP authentication to enhance security for

an iSCSI connection.

Refer

-"2.1.6 Setting CHAP Authentication" (page

13)

Setting the CA Reset Groups

Assign the iSCSI ports of the ETERNUS DX to the same reset group, depending on the connection

conditions.

Refer

-"2.2.1 Setting the CA Reset Groups" (page 14)

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

Chapter 2

ETERNUS DX Connection Settings

2.1 Common Settings

This section explains the settings required for all server OSs, regardless of the connection configuration. For

details of how to use ETERNUSmgr to perform these settings, refer to the "ETERNUSmgr User Guide".

2.1.1 Setting the To-server Connection Type (Setting the CA Parameters)

For each connection configuration, perform the following iSCSI port parameter settings only. All other

parameters should be left on their default values.

Table 2.1 CA parameter settings (iSCSI port settings)

Parameter Solaris OS, HP-UX, Windows®, Linux, VMware ESX, Oracle VM Server

TCP/IP Setting

IP Address Arbitrary

Subnet Mask Arbitrary

Gateway Arbitrary

iSNS Server Select "ON" to use the iSNS server, and specify the IP address for the iSNS

server.

iSCSI Settings

iSCSI Name Arbitrary

Caution:

When configuring multipaths, specify a different name for each iSCSI port.

If the same iSCSI name is specified for multiple ports, connection via

multipaths may not be available.

Alias Name Arbitrary

Security

CHAP OFF (Default value): When both unidirectional CHAP authentication and

bidirectional CHAP authentication are not used

ON: When either unidirectional CHAP authentication or bidirectional CHAP

authentication is used

User Name When using bidirectional CHAP authentication, set a password.

When using unidirectional CHAP authentication, a CHAP user name and

password do not need to be set.

New Password

New Password (Re-enter)

General Settings

Affinity Mode OFF (Default value): When not using Affinity Mode

ON: When using Affinity Mode

Host Affinity ON

Host Response Not available ( When "Host Affinity" is set to "ON")

Chapter 2 ETERNUS DX Connection Settings

2.1 Common Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

2.1.2 Sense Data Conversion (Setting the Host Responses)

The ETERNUS DX host responses must be set to match the way in which the server will process the ETERNUS DX

request responses.

These are different for each OS and this must be done before connecting the ETERNUS DX to the server.

Retain the default values for all parameters not described below.

2.1.2.1 Solaris OS

For Solaris OS, perform the settings detailed in Table 2.2 and Table 2.3.

Table 2.2 Reservation Conflict Response for Test Unit Ready setting for Solaris OS

Table 2.3 Sense Data Conversion Pattern setting for Solaris OS

2.1.2.2 HP-UX

For HP-UX, set the [Host Specific Mode] to [HP-UX Mode (SCC)].

Table 2.4 Host Specific Mode setting for HP-UX

Reset Scope I_T_L (Default value)

Reserve Cancel at Chip Reset OFF (Default value)

Header Digest OFF (Default value)

Data Digest OFF (Default value)

Parameter Solaris OS, HP-UX, Windows®, Linux, VMware ESX, Oracle VM Server

OS MPxIO (OS standard Multipath Driver)

Used Not used

Solaris 10 OS Conflict Response Normal Response (Default)

OS [Sense Data Conversion Pattern]

setting

Solaris 10 OS Linux Recommended

(When not using GRMPD)

OS [Host Specific Mode] setting

HP-UX HP-UX Mode (SCC)

Chapter 2 ETERNUS DX Connection Settings

2.1 Common Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

2.1.2.3 Windows®

For Windows®, perform the settings detailed in Table 2.5 and Table 2.6.

Table 2.5 Reservation Conflict Response for Test Unit Ready setting for Windows®

When a Windows® server and ETERNUS DX are connected via a single path connection using an ETERNUS

Multipath Driver, set the host response Sense Data Conversion Pattern to [No Conversion].

If connection is performed without using an ETERNUS Multipath Driver, set the host response Sense Data

Conversion Pattern to [Windows Recommended (When not using GR/ETERNUS MPD or Device Driver)].

Table 2.6 Sense Data Conversion Pattern setting for Windows®

When connecting a Windows®-based VMware VCB Proxy server to the ETERNUS DX, and the LUNs are shared

between the VMware VCB Proxy server and VMware ESX server, the settings detailed in "2.1.2.5 VMware ESX"

(page 11) should be used.

2.1.2.4 Linux

For Linux, perform the settings detailed in Table 2.7.

Table 2.7 Sense Data Conversion Pattern setting for Linux

OS MSCS or WSFC configuration All other configurations

Windows Server® 2012 R2

Windows Server® 2012

Windows Server® 2008 R2

Windows Server® 2008

Normal (Default) Normal (Default)

Windows Server® 2003 Conflict

ETERNUS Multipath Driver,

ETERNUS Device Driver msdsm

Used Not used

Windows Server® 2012 R2

Windows Server® 2012

Windows Server® 2008 R2

Windows Server® 2008 No Conversion (Default)

Windows Recommended

(When not using GR/

ETERNUS MPD or Device

Driver)

Windows

Recommended (When

not using GR/ETERNUS

MPD or Device Driver)

Windows Server® 2003 —

OS ETERNUS Multipath Driver

Not used

Red Hat Enterprise Linux

SUSE Linux Enterprise Server

Linux Recommended

(When not using GRMPD)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Fujitsu

Fujitsu

Fujitsu Eternus DX80 S2 Manual de instrucciones

Fujitsu

Fujitsu ETERNUS AB Series Instrucciones de montaje

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu MHV2120BH Manual de usuario

Fujitsu

Fujitsu MPG3XXXAH-E Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu FD-1100MT Manual de usuario

Fujitsu

Fujitsu ETERNUS AF250 S2 Manual de usuario

Fujitsu

Fujitsu MHT2060BH - Mobile 60 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 S4 Manual de usuario

Fujitsu

Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu MAN3735 SERIES Manual de usuario

Fujitsu

Fujitsu ETERNUS DX100 S3 Manual de usuario

Fujitsu

Fujitsu ETERNUS SF Express V16.6 Manual de usuario

Fujitsu

Fujitsu Streamer DAT 160 Manual de usuario

Fujitsu

Fujitsu eternus af Manual de usuario

Fujitsu

Fujitsu teamserver Series Manual de usuario

Fujitsu

Fujitsu M2488 Manual de usuario

Fujitsu

Fujitsu MAT3300NC/NP Product/ Manual de usuario

Fujitsu

Fujitsu ETERNUS LT20 S2 Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 Manual de referencia

Fujitsu

Fujitsu DynaMO 1300 Manual de usuario

Fujitsu

Fujitsu ETERNUS AX Series Manual de usuario

Fujitsu

Fujitsu Eternus DX80 S2 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario