Fujitsu ETERNUS DX Disk Manual de usuario

FUJITSU Storage

ETERNUS DX

Configuration Guide -Server Connection-

(SAS) for Linux

P3AM-3472-14ENZ0

This page is intentionally left blank.

Preface

This manual briefly explains the operations that need to be performed by the user in order to connect an

ETERNUS DX to a server running Linux via a SAS interface.

This manual should be used in conjunction with any other applicable user manuals, such as those for the

ETERNUS DX, server, OS, SAS cards, and drivers.

Refer to "Configuration Guide -Server Connection- Notations" for the notations used in this manual such as

product trademarks and product names. For storage systems that are supported by the OS, refer to the Server

Support Matrix of the ETERNUS DX.

14th Edition

April 2018

The Contents and Structure of this Manual

This manual is composed of the following ten chapters.

•"Chapter 1 Workflow" (page 6)

This chapter describes how to connect the ETERNUS DX storage systems to a server running Linux.

•"Chapter 2 Checking the Server Environment" (page 10)

This chapter describes which servers can be connected to ETERNUS DX storage systems.

•"Chapter 3 Notes" (page 11)

This chapter describes issues that should be noted when connecting the ETERNUS DX storage systems and

server.

•"Chapter 4 Setting Up the ETERNUS DX" (page 13)

This chapter describes how to set up the ETERNUS DX storage systems using ETERNUS Web GUI.

•"Chapter 5 Setting Up the SAS Switches" (page 14)

This chapter describes how to set up the SAS switches.

•"Chapter 6 Installing the Driver" (page 16)

This chapter describes how to install the SAS card driver.

•"Chapter 7 Setting Up the Server" (page 17)

This chapter describes how to make the server recognize the SAS card.

•"Chapter 8 LUN Recognition" (page 18)

This chapter describes how to make the server recognize the LUNs of the ETERNUS DX.

•"Chapter 9 Setting Up and Checking the Multipath Driver" (page 21)

This chapter describes how to set multipaths for multipath connection.

•"Chapter 10 Setting a File System" (page 22)

This chapter describes how to create a file system.

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Table of Contents

Chapter 1 Workflow 6

1.1 When the Multipath Driver is not Used........................................................................................... 6

1.2 When the Multipath Driver is Used................................................................................................. 8

Chapter 2 Checking the Server Environment 10

2.1 Hardware ..................................................................................................................................... 10

2.2 Operating System (OS)................................................................................................................. 10

2.3 SAS Cards...................................................................................................................................... 10

2.4 ETERNUS Multipath Driver or device-mapper multipath ............................................................... 10

Chapter 3 Notes 11

3.1 SAS Card Notes ............................................................................................................................. 11

3.2 Server Startup Notes..................................................................................................................... 11

3.3 Red Hat Enterprise Linux Notes.................................................................................................... 11

3.4 SUSE Linux Enterprise Server Notes.............................................................................................. 11

3.5 Notes on Creating and Mounting File Systems ............................................................................. 12

3.6 Notes on Changing the max_sectors_kb Value ............................................................................. 12

Chapter 4 Setting Up the ETERNUS DX 13

Chapter 5 Setting Up the SAS Switches 14

Chapter 6 Installing the Driver 16

6.1 For Fujitsu SAS Cards .................................................................................................................... 16

6.2 For LSI Logic SAS Cards ................................................................................................................. 16

Chapter 7 Setting Up the Server 17

7.1 For Fujitsu SAS Cards .................................................................................................................... 17

7.2 For LSI Logic SAS Cards ................................................................................................................. 17

Chapter 8 LUN Recognition 18

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

8.1 Setting Up the Server to Recognize LUNs...................................................................................... 18

8.2 Displaying the Recognized Logical Units ...................................................................................... 19

8.2.1 For Red Hat Enterprise Linux or Oracle Linux ......................................................................................................19

8.2.2 For SUSE Linux Enterprise Server.........................................................................................................................20

Chapter 9 Setting Up and Checking the Multipath Driver 21

9.1 Setting Up and Checking the ETERNUS Multipath Driver............................................................... 21

9.2 Setting Up and Checking the device-mapper multipath ............................................................... 21

Chapter 10 Setting a File System 22

Table of Contents

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Chapter 1

Workflow

This chapter describes how to connect the ETERNUS DX to a server running Linux.

Which documents need to be referred to varies with the connection environment. Refer to the workflow that

follows to determine which documents are required.

Required Documents

•"Server Support Matrix"

•"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETERNUS DX to

be connected

•"Configuration Guide -Server Connection- (Fibre Channel/FCoE/iSCSI/SAS) for Linux device-mapper multi-

path"

•"ETERNUS Web GUI User's Guide"

•Manuals supplied with the server, SAS cards, and multipath driver

1.1 When the Multipath Driver is not Used

The documents and workflow required when a multipath driver is not used are as follows.

Workflow

Setting Up the ETERNUS DX

Set the various parameters required to operate the ETERNUS DX.

•Checking the setup and maintenance operations

-"Chapter 2 Checking the Server Environment" (page 10)

-"Chapter 4 Setting Up the ETERNUS DX" (page 13)

-"ETERNUS Web GUI User's Guide"

•Setting up the ETERNUS DX

-"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETER-

NUS DX to be connected

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Setting Up the SAS Switches

Set up the SAS switch.

•"Chapter 5 Setting Up the SAS Switches" (page 14)

Installing the Driver

Install the appropriate driver for the SAS card being used.

•Checking the SAS card driver versions

-"Chapter 6 Installing the Driver" (page 16)

-"Server Support Matrix"

Setting Up the Server

Set the parameters required for connection to the ETERNUS DX.

•"7.1 For Fujitsu SAS Cards" (page 17)

•"7.2 For LSI Logic SAS Cards" (page 17)

Setting Up the Server to Recognize the Logical Units

Set up the server so that it can recognize the LUNs (logical unit numbers) of the ETERNUS DX.

•"Chapter 8 LUN Recognition" (page 18)

Chapter 1 Workflow

1.1 When the Multipath Driver is not Used

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

1.2 When the Multipath Driver is Used

The documents and workflow required when a multipath driver is used are as follows.

Workflow

Setting Up the ETERNUS DX

Set the various parameters required to operate the ETERNUS DX.

•Checking the setup and maintenance operations

-"Chapter 2 Checking the Server Environment" (page 10)

-"Chapter 4 Setting Up the ETERNUS DX" (page 13)

-"ETERNUS Web GUI User's Guide"

•Setting up the ETERNUS DX

-"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETER-

NUS DX to be connected

Setting Up the SAS Switches

Set up the SAS switch.

•"Chapter 5 Setting Up the SAS Switches" (page 14)

Installing the Driver

Install the appropriate driver for the SAS card being used.

•Checking the SAS card driver versions

-"Chapter 6 Installing the Driver" (page 16)

-"Server Support Matrix"

Chapter 1 Workflow

1.2 When the Multipath Driver is Used

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Setting Up the Server

Set the parameters required for connection to the ETERNUS DX.

•"7.1 For Fujitsu SAS Cards" (page 17)

•"7.2 For LSI Logic SAS Cards" (page 17)

Setting Up the Server to Recognize the Logical Units

Set up the server so that it can recognize the LUNs (logical unit numbers) of the ETERNUS DX.

•"Chapter 8 LUN Recognition" (page 18)

When the ETERNUS Multipath Driver is used When the device-mapper multipath is used

Setting Up and Checking the ETERNUS Multi-

path Driver

Set up and check the ETERNUS Multipath Driver.

•"9.1 Setting Up and Checking the ETERNUS Mul-

tipath Driver" (page 21)

Setting Up and Checking the device-mapper

multipath

Set up and check the device-mapper multipath.

•"9.2 Setting Up and Checking the device-mapper

multipath" (page 21)

•"Configuration Guide -Server Connection- (Fibre

Channel/FCoE/iSCSI/SAS) for Linux device-map-

per multipath"

Chapter 1 Workflow

1.2 When the Multipath Driver is Used

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Chapter 2

Checking the Server Environment

Connection to servers is possible in the following environments.

Check the "Server Support Matrix" for server environment conditions.

2.1 Hardware

Refer to the "Server Support Matrix".

2.2 Operating System (OS)

Refer to the "Server Support Matrix".

2.3 SAS Cards

Refer to the "Server Support Matrix".

2.4 ETERNUS Multipath Driver or device-mapper multipath

Refer to the "Server Support Matrix".

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (SAS) for Linux

P3AM-3472-14ENZ0

Otros manuales para ETERNUS DX Disk

Tabla de contenidos

Otros manuales de Almacenamiento de Fujitsu

Fujitsu

Fujitsu MJA2500BH - Mobile 500 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu MBC2073RC SERIES Manual de usuario

Fujitsu

Fujitsu RE25U Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu M2266S Nota de versión

Fujitsu

Fujitsu PG-HDH97A Manual de usuario

Fujitsu

Fujitsu M2488 Manual de usuario

Fujitsu

Fujitsu MHW2040BS Manual de usuario

Fujitsu

Fujitsu ETERNUS DX500 S4 Manual de usuario

Fujitsu

Fujitsu MHU2100AT Manual de usuario

Fujitsu

Fujitsu Eternus DX80 S2 Manual de usuario

Fujitsu

Fujitsu RDX USB 3.0 QuikStor Drive Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 S2 Manual de usuario

Fujitsu

Fujitsu MPG3XXXAH-E Manual de usuario

Fujitsu

Fujitsu P3AM-5382-03ENZ0 Cómo utilizar

Fujitsu

Fujitsu ETERNUS AF S3 Series Instrucciones de montaje

Fujitsu

Fujitsu MPC3096AT - Desktop 9.7 GB Hard Drive Manual de usuario

Fujitsu

Fujitsu SPARC S7-2 Manual de usuario

Fujitsu

Fujitsu GP5-HDH8B Manual de usuario

Fujitsu

Fujitsu MPG3XXXAH Manual de usuario

Fujitsu

Fujitsu DynaMO 640SZI Manual de usuario

Fujitsu

Fujitsu ETERNUS DX Disk Manual de usuario

Fujitsu

Fujitsu MAX3036RC SERIES Manual de usuario

Fujitsu

Fujitsu ETERNUS DX60 S3 Manual técnico

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario