Front Runner KRJW021T Manual de usuario

ENG

180 min

Jeep Wrangler JKU 4 Door (2007-Current)

Slimline II Extreme ½Roof Rack Kit

Foot Rail

IMPORTANT WARNING!

Don’t be a hero and muscle through this without ﬁrst reading these ﬁtting instructions! Improper installation of this gear may void certain aspects of

your warranty.

Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.

A complete kit will contain:

1. A Front Runner Mounting System speciﬁc to your vehicle

2. A Front Runner Rack Tray or Load Bar Slats

This document will guide you through the assembly of the mounting system and assist you in ﬁtting the roof rack tray or load bars to your speciﬁc

vehicle.

Please refer to the next page for a list of all the components, quantities and tools required.

KRJW021T

READ ME FIRST

START HERE!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

IN THE BOX

FIGURE 1.1

1 2 X Inner Roll Bar Clamp

2 2 X Outer Roll Bar Clamp

3 28 X M6 x 12 x 1SS Flat Washer

4 16 X Foam Seal Washer

5 16 X Aluminum Spacer

6 16 X M6 x 30 Hex Bolt

7 20 X M6 Nyloc Nut

8 8 X M6 x 20 Hex Bolt

9 20 X M6 Nut Cap

10 16 X M6 x 19 x 1SS Flat Washer

11 2 X Rear Support Bracket - 1LH + 1RH

12 2 X M8 x 75 Hex Bolt

13 2 X M8 Large Washer

14 2 X Middle Support Bracket - 1LH + 1RH

15 16 X Sealing Plug Assembly

IN THE BOX TOOLS NEEDED

T40

Torx Wrench

IN THE BOX

989

14L

14R

11R

11L

1GET ORGANIZED

Here is what you are looking at for FAJK002

13MM

10MM 10MM

13MM

6mm

22mm (7/8") Hole Saw

KRJW021T_REV_C00

16R

16L

1GET ORGANIZED

FIGURE 1.2

IN THE BOX

15 14 X M8 X 16 Hex Bolt

16 2 X Foot Rail - 1LH + 1RH

17 14 X M8 x 16 x 1.6SS Flat Washer

18 14 X M8 Nyloc Nut

19 14 X M8 Nut Cap

IN THE BOX IN THE BOX

Here is what you are looking at for FAJK006

KRJW021T_REV_C00

PREP FOR INSTALLATION OF REAR SUPPORT ARMS (FAJK002)

13mm

2.1

2.2

2.3

Loosen velcro, unzip and remove the

padding covering the roll bars.

Remove the wiring harness and plastic

clip from the roll bar.

Loosely attach the Rear Support Arms

(item 11) to the outside of the Roll Bar

Clamps using items 3, 7 & 8. Make sure

the foot faces to the inside of the vehicle

and the contours of the foot match the

contours of the roof as shown.

Mark the position of the four holes in the

foot on the roof.

Once the holes have been marked

remove the Rear Support Arms.

Pilot drill the marked holes using a 6mm

drill bit.

Locate the two threaded holes on the

underside of the roll bar and fasten the

two halves of the Roll Bar Clamps (Items

1 & 2) to the roll bar using items 3 & 8.

Place the outer half of the clamp ﬁrst.

10mm

6mm

KRJW021T_REV_C00

PREP AND INSTALLATION MIDDLE SUPPORT ARMS (FAJK006)

13mm

3.1

3.2

3.3

Locate the Foot Rail in position by lining

up the holes in the bracket with the

holes drilled in Step 2.3.

Place a M6 x 30 Hex Bolt (item 6) into

each hole to keep its location.

Once you are happy with your

measurements and alignment, mark the

four holes in the foot of the Foot Rail

onto the roof.

Remove the Foot Rail.

From outside the vehicle, using your

6mm drill bit, drill the four pilot holes

through the marks you just made.

Repeat Step 2.1 to 3.3 for the opposite

side.

Using a measuring tape and a rib in the

roof as a reference, adust the front of

the bracket so that the entire length of

the bracket is parallel with your

reference rib.

FRONT OF VEHICLE

SIDE VIEW OF FOOT RAIL

TOP VIEW OF FOOT RAIL

REAR FOOT

10mm

6mm

KRJW021T_REV_C00

FIT AND SECURE

13mm

3.4

3.5

3.6

Change from the 6mm drill bit to a

22mm hole saw. From the outside of the

vehicle drill all the 6mm holes (16 in

total) out to 22mm. Once again, let the

drill do the work. You do not want to

scratch or damage your vehicle's roof.

You may wish to have a friend inside the

vehicle with a vacuum cleaner

underneah where you are drilling to

catch all the dust and keep your vehicle

clean.

From the inside of the vehicle, in the

same position as where you just

inserted the bolt in Step 3.5, push the

Middle Support Bracket (Item 14)

through the hole in the roll bar padding

and loosely fasten it to the roll bar.

Please note that there is a left hand and

right hand bracket. The arrow on the

bracket must point to the rear of the

vehicle.

Pull back the padding around the roll bar

above the rear seats and insert Items 12

& 13 (from FAJK002 box) through the

hole as shown.

13mm

22mm

TIP - It is easier to do the next step if

you remove the roof.

KRJW021T_REV_C00

INSTALLATION OF REAR SUPPORT ARMS

13mm

4.1

Reﬁt and fasten the Rear Support Arms

as in Step 2.3

10mm

5PREP FOR RACK INSTALL (FAJK002)

5.1

5.2

Clean the area around all the 22mm

holes drilled in the roof with a rag and

methylated spirits/denatured alcohol.

Insert the Aluminum Spacers (Item 5)

into the Foam Washer (Item 4). Remove

the paper backing from the Foam

washer to expose the adhesive.

Insert the washer/spacer combination,

adhesive side down, into the 22mm

holes so that the spacer comes to rest

on the Rear Support Brackets

underneath.

Firmly press the foam washer all the

way around securing it to the roof.

NOTE: Use the worm slots to adjust the

height of the rear support brackets.

This will be important to create a

weatherproof Seal.

If not already assembled, assemble your

Tray as per the Universal Tray Assembly

Instructions (Document RRSTUNI)

NOTE: Before ﬁtting the wind

deﬂector, insert the M8 x 20 Hex

Bolts (item 15 from FAJK003 box)

into the ﬁrst slat (Combined Slat)

using the machined slot. Slide a

bolt to each of the outer corners.

80mm

KRJW021T_REV_C00

6.1

6.2

MOUNT YOUR TRAY

With the help of a friend, ﬂip the Tray

end over end so that it is in the upright

position. (The Tray is ﬂipped end over

end so that bolts and brackets do not

slide left and right).

With one of you on either side of the

Tray, lift the Tray and walk it into

position above the vehicle, approaching

from either the front or the rear of the

vehicle.

The Foot Rail should still be loose

enough to move. Line the brackets up

with the holes on the roof and fasten

them into position using Items 3, 6, 7 &

10 (from FAJK002 box). Centre the tray

from left to right. Use a tape measure to

double check. Once you are happy that

the Tray is in the correct position, fasten

all the nuts and bolts, both inside and

outside of the vehicle on all brackets

that were installed.

Push the Plastic Nut Caps (Item 9 from

FAJK002 box) provided over all the

exposed bolts and close up all the roll

bar padding.

11L

14L

13mm

REMOVING YOUR RACK5

5.3

After ﬁtting the wind deﬂectors, the tray

should still be upside down, loosely

mount the Foot Rail (from FAJK006 box)

to the Tray using items 15, 17 & 18. As

before use the machined slots to insert

the hex bolts into the Slats. The Foot Rail

should be mounted at the opposite end

of the Tray to the wind deﬂector.

The rear of the Foot Rail must mount

onto the very last Slat(Combined Slat)

and approximately 80mm in from the

outer edge of the side of the Tray. Do not

tighten the bolts yet.

13mm

KRJW021T_REV_C00

13mm

REMOVING YOUR RACK7

7.1

Should you wish to remove your rack,

you will need to plug the holes you

drilled in the roof (Step 3.4), using the

supplied Sealing Plug Assemblies.

Remove the Tray, Front Uprights and the

Foot Rail, by reversing the instillation

procedure. Leave the Foam Washer and

the Aluminum Spacers in place. Screw in

the Sealing Plugs reusing the M6 Nyloc

Nuts and Washers that held the Foot Rail

in position.

12mm

TAKE A TRIP

After your ﬁrst adventure, check that all nuts, bolts, screws and ﬁttings are tight. Re-tighten where needed. You'll ﬁnd a

small amount of settling has happened.

Go on many more adventures, periodically checking all nuts, bolts, screws and ﬁttings.

8.1

Front Runner can not recommend a maximum load carrying capacity. Please refer to your vehicle manufacturer's

recommendations

KRJW021T_REV_C00

COMPLETION

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or online.

9.1

Congratulations. You did it. Take a step back and admire your work!

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Front Runner

Front Runner

Front Runner SSDS109 Manual de usuario

Front Runner

Front Runner SSDR011 Manual de usuario

Front Runner

Front Runner LALD005 Manual de usuario

Front Runner

Front Runner RTTENT101 Manual de usuario

Front Runner

Front Runner SSDS113 Manual de usuario

Front Runner

Front Runner SSBS008 Manual de usuario

Front Runner

Front Runner SSDS111 Manual de usuario

Front Runner

Front Runner BGTH002 Manual de usuario

Front Runner

Front Runner TBRA020 Manual de usuario

Front Runner

Front Runner FAJK002 Manual de instrucciones

Front Runner

Front Runner QE Series Manual de usuario

Front Runner

Front Runner RRAC210 Manual de usuario

Front Runner

Front Runner LAMG003 Manual de usuario

Front Runner

Front Runner KRTT950T Manual de usuario

Front Runner

Front Runner RRAC129 Manual de usuario

Front Runner

Front Runner TBRA034 Manual de usuario

Front Runner

Front Runner Wolfpack Pro RRAC257 Manual de usuario

Front Runner

Front Runner MKIII Small Manual de usuario

Front Runner

Front Runner SSDR003 Manual de usuario

Front Runner

Front Runner FAJK007 Manual de usuario

Front Runner

Front Runner TRCA005 Manual de usuario

Front Runner

Front Runner 200 Series Manual de usuario

Front Runner

Front Runner KRLDT03L Manual de instrucciones

Front Runner

Front Runner LATF001 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario