Front Runner GBHO012 Manual de usuario
GBHO012_REV_A01
Gas / Propane
Bottle Holder
front runner
GBHO012
ENG
1
Thank you for purchasing a Front Runner Gas / Propane Bottle Holder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
GBHO012_REV_A01
2
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
1
5
6
7
2
8
4
3
3
2
1 1 X Top Collar
2 2 X Base Clamp Bracket
3 2 X Tensioner Bar
4 2 X T - Slot Rubber
5 4 X M8 Nut Cap
6 4 X M8 Nyloc Nut
7 4 X M8 x 16 x 1.6 SS Flat Washer
8 4 X M8 x 16 Hex Bolt
13mm 13mm
GBHO012_REV_A01
3
FIT AND SECURE - MOUNTING BRACKETS ON TOP OF SLATS2
2.1
2.2
2.3
13mm
Find a suitable place between two slats to
mount your Gas Bottle Holder.
Slide two M8 x 16 Hex Bolts (Item 8) into the
machined slots of the slats you have chosen,
followed by the Base Clamp Bracket (Item 2).
Loosely fit using M8 x 16 x 1,6SS Flat
Washers and M8 Nyloc Nuts (Items 6 & 7).
The position of the Base Clamp Brackets will
depend on the size of your gas bottle.
Place your gas bottle between the two Base
Clamp Brackets. Slide the Clamps together
until they are touching up against the gas
bottle and tighten the four M8 Nyloc.
Place M8 Nut Caps (Item 5) on the Nyloc
Nuts.
Insert the T-Slot Rubber (Item 4) between
the two Base Clamp Brackets as shown.
You may need to trim the T-Slot Rubber
depending on the width between the
brackets.
Place the Top Collar (Item 1) over the gas
bottle so that you can adjust the length of
the two Tensioner Bars (Item 3) according
to the height of the gas bottle.
To adjust, screw the Tensioner Bars in or out
of the Top Collar until the required height is
obtained.
Insert the Tensioner Bars between the slots
in the Base Clamp Brackets. Secure the
bottle in position by closing the latches.
5
6
7
2
8
4
3
1
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
GBHO012_REV_A01
4
FIT AND SECURE - MOUNTING BRACKETS AT THE BOTTOM OF THE SLATS3
3.1
3.2
3.3
Find a suitable place between two slats to
mount your Gas Bottle Holder.
Slide two M8 x 16 Hex Bolts (Item 8) into the
machined slots underneath the slats you
have chosen, followed by the Base Clamp
Brackets (Item 2).
Loosely fit using M8 x 16 x 1,6SS Flat
Washers and M8 Nyloc Nuts (Items 6 & 7).
The position of the Base Clamp Brackets will
depend on the size of your gas bottle.
Place your gas bottle between the two Base
Clamp Brackets. Slide the Clamps together
until they are touching up against the gas
bottle and tighten the four M8 Nyloc Nuts.
Place M8 Nut Caps (Item 5) on the Nyloc
Nuts.
Insert the T-Slot Rubber (Item 4) between
the two Base Clamp Brackets as shown.
Place the Top Collar (Item 1) over the gas
bottle so that you can adjust the length of
the two Tensioner Bars (Item 3) according
to the height of the gas bottle.
To adjust, screw the Tensioner Bars in or out
of the Top Collar until the required height is
obtained.
Insert the Tensioner Bars between the slots
in the Base Clamp Brackets. Secure the
bottle in position by closing the latches.
13mm
4
5
6
7
2
8
3
1
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
GBHO012_REV_A01
5
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
4
Congratulations! You did it. Take a step back and admire your work!
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Front Runner
Front Runner
Front Runner LAMG002 Manual de usuario
Front Runner
Front Runner SSDR010 Manual de usuario
Front Runner
Front Runner FAJL002 Manual de usuario
Front Runner
Front Runner Slimline II KRVA002T Manual de usuario
Front Runner
Front Runner BPTH007 Manual de usuario
Front Runner
Front Runner TBRA020 Manual de usuario
Front Runner
Front Runner RRAC178 Manual de usuario
Front Runner
Front Runner SSBS008 Manual de usuario
Front Runner
Front Runner TBMK009 Manual de usuario
Front Runner
Front Runner FAJK009 Manual de usuario
Front Runner
Front Runner VACC120 Manual de usuario
Front Runner
Front Runner KRTT001T Manual de usuario
Front Runner
Front Runner TRAC003 Manual de usuario
Front Runner
Front Runner SSDR005 Manual de usuario
Front Runner
Front Runner BRONCO TBRA040 Manual de usuario
Front Runner
Front Runner LADD007 Manual de usuario
Front Runner
Front Runner LAVT003 Manual de usuario
Front Runner
Front Runner BGTH002 Manual de usuario
Front Runner
Front Runner SAFE010 Manual de usuario
Front Runner
Front Runner KRJW021T Manual de usuario
