Follett Horizon HCC1000AJS Manual de usuario

Order parts online

www.follettice.com

Horizon™icemaker Installation Instructions

for Drop-In Satellite-ll™applications

208264

StockModule Identification Plate

ServiceNo.

ModuleNo.

Product

OMRESSORTHERMALLYPROTECTED

EastonPennsylvania

AMPS

VOLTSPHASE

SINGLE

CHARGE

LOWSIDE

PARTNO

PSIG

THEUSA

MADEIN

NSF

HCC1000AJS, HCC1400AJS, HCC1000WJS, HCC1400WJS,

HCE1000AJS, HCE1400AJS, HCE1000WJS, HCE1400WJS

(See model number congurator on page 2 for details.)

self-contained

00159939R03

801 Church Lane • Easton, PA 18040, USA

Toll free (800) 523-9361 • (610) 252-7301

Fax (610) 250-0696 • www.follettice.com

2self-contained DROP-IN • SATELLITE-FILL

Horizon Series Icemaker Model Number Configurations

A Air-cooled, self-contained

W Water-cooled, self-contained

R Air-cooled, remote condensing unit

N Air-cooled, no condensing unit for

connection to parallel rack system

AVSC 1400HC

HC Horizon

Chewblet®

C 208-230/60/1

(self-contained only)

D Low side 115/60/1

Condensing unit

208-230/60/1

(remote condensing only)

E 230/50/1

(self-contained only)

Icemaker Voltage Series Condenser

V Vision™

H Harmony™

B Ice storage

bin

J Drop-in

M Ice Manager†

diverter valve

system

1000 up to

1036 lbs

(471kg)

1400 up to

1450 lbs

(658kg)

S Satellite-fill™

T Top-mount

Application Configuration

† Ice Manager Diverter Valve Systems can be used to fill any two of these bins or dispensers with a single ice machine.

Chewblet is a registered trademark of Follett Corporation, registered in the US.

DROP-IN • SATELLITE-FILL self-contained

Front cover

Internal connection

Ice transport tube

External connection

Louvered docking assembly

Dispenser preparation

Site preparation

Unpack

Read and complete the following 8 installation steps

Follett Corporation

Equipment Return Policy

Follett equipment may be returned for credit under the following conditions:

1. The equipment is new and unused.

2. A return authorization number has been issued by customer service within 30 days after shipment.

3. Follett receives the equipment at the factory in Easton, PA within 30 days after issuance of the return authorization number.

4. The equipment must be returned in Follett packaging. If the packaging has been damaged or discarded, Follett will forward, at the customer’s

expense, new packaging.

Note: Return freight charges are the responsibility of the customer. If equipment is returned and is damaged because of improper packaging, Follett

Corporation will not be held responsible.

Credit will be issued when:

The equipment has been inspected by Follett and deemed suitable to be returned to stock.

Note: A 15% restocking charge will be deducted from the credit. If the cost to return the product to stock exceeds 15%, the actual cost will be

deducted.

4self-contained DROP-IN • SATELLITE-FILL

Carefully unpack and inspect the contents of your Follett icemaker. 1

Unpack

1/2"

➊➋

➌➍

➎➏

Unpack icemaker

1. 1

DROP-IN • SATELLITE-FILL self-contained

1/4˝

➍

➋

➌

➊

208264

StockModule Identification Plate

ServiceNo.

ModuleNo.

Product

OMRESSORTHERMALLYPROTECTED

EastonPennsylvania

AMPS

VOLTSPHASE

SINGLE

CHARGE

LOWSIDE

PARTNO

PSIG

THEUSA

MADEIN

NSF

NEMA

6-15

HCC1000A/W

HCC1400A/W

NEMA

6-20

HCE1000A/W ‡

requires 15 amp circuit

1.50 mm2wire

HCE1400A/W ‡

requires 20 amp circuit

4.00 mm2wire

Prepare the installation site. 2

Site preparation

2.1

Provide drainage, water supply and electrical power to within 6 feet (2m) of

icemaker in accordance with local and national codes. Outdoor installation is

not recommended and will void warranty.

Electrical ➊

• HCC1000(A/W)JS 208-230/60/1-15 amps • HCC1400(A/W)JS 208-230/60/1-20 amps

• HCE1000(A/W)JS 230/50/1-15 amps‡• HCE1400(A/W)JS 230/50/1-20 amps‡

(HCE1000A/W Requires 15 amp circuit 1.50 mm2wire) (HCE1400A/W Requires 20 amp circuit 4.00 mm2wire)

‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.

Potable water supply ➋

• 10-70 psi (69-483kpa)

• 45 to 90 F (7 to 32 C)

• Follett recommends the use of an in-line water filtration system (item# 00130286)

Condenser water supply for water-cooled systems ➌

• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)

• 45 to 90 F (7 to 32 C)

• 1.5 gallons per minute (5.68 liters per minute)

Drain ➍

• The drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m)

Installation site requirements

2.1

6self-contained DROP-IN • SATELLITE-FILL

12"

(304,8mm)

min.

(101,6mm)

➌

➍

➓

➑

➋

➏

➎

➊

➐

Hot Water

➒

Prepare the dispenser. 3

Dispenser preparation

• Determine best route for ice transport tube run. Note: 12" (304,8mm) clearance is required.

• Drill 1 3/4" (44,5mm) hole through either side of dispenser ➊

• Install gasket

➋onto bulkhead fitting ➌

• Attach bulkhead fitting with flat up ➍and tighten bulkhead nut ➎

• Position and secure nut locking plate ➏with supplied screws

• Verify installation of O-ring on stainless steel ice transport tube coupling ➐

• Insert stainless steel ice transport tube coupling ➐into bulkhead fitting and secure with

coupling cap ➑

• Soften ice transport tube with hot water (160 F (71 C)) to ease assembly ➒

• Attach ice transport tube to coupling with supplied hose clamp ➓

2.1 Dispenser preparation

3.1

DROP-IN • SATELLITE-FILL self-contained

8self-contained DROP-IN • SATELLITE-FILL

Install the louvered docking assembly.

Louvered docking assembly 4

DOCKING STATION: Horizon 1000 & 1400 water- and air-cooled models

(See detail drawing on page 9)

• Position and screw louvered docking assembly to the bottom of counter inside of access

panel/door 1.75" (45mm) from the front edge of the cross brace ➊

• The mounting surface for the louvered docking assembly must be solid.

Do not mount directly onto runners or channels.

• There must be no lip or edge that would hinder the icemaker from sliding in or out of the

louvered docking station ➋

INTAKE AND EXHAUST GRILLE PLACEMENT: Horizon 1000 & 1400 air-cooled models only

(See detail drawing on page 9)

• Position the intake grille cut out in the access panel/door

Note: Icemaker must be aligned with cut out and inside of access panel to provide a tight

seal and prevent recirculation of hot exhaust air.

• Left edge of cutout should be 1.75" (45mm) from the left side of the icemaker ➌

• Bottom edge of cutout should be 1.875" (48mm) from the bottom of the icemaker ➍

• Position supplied exhaust grille at least 18" (458mm) away from intake grille ➎.

Where possible, install exhaust grille to the rear or side of the base cabinet.

• If not using supplied grille, air circulation requirements below must be met:

1000 series: 150 sq. in (967 sq cm) intake air, 150 sq. in (967 sq. cm) exhaust air

1400 series: 175 sq. in (1129 sq. cm) intake air, 175 sq. in (1129 sq. cm) exhaust air

Undercounter installation requirements Horizon 1000 & 1400 series

4.1

WARNING

• Docking station must be secured in accordance with these instructions to ensure icemaker stability.

• Ventilation openings in the louvered docking station should be clear of obstruction

Wall bracket accessory Machine stand accessory

• Mount louvered docking assembly to wall

bracket accessory

• Mount louvered docking assembly to

machine stand accessory

DROP-IN • SATELLITE-FILL self-contained

CROSSBRACE

Front View

3D Counter View

Top View

Access panel/

door on counter

1.75" (45mm)

bottom of ice machine

side of ice machine

1000 series - 12"x16" cutout (305x407mm)

1400 series - 16"x16" cutout (407x407mm)

1.875"

(48mm)

1000 series - 12" (305mm)

1400 series - 16" (407mm)

16"

(407mm)

18" min.

(458mm)

1000 series - 28.6" min. (727mm)

1400 series - 31.6" min. (303mm)

24.5" min.

(623mm)

No Lip

➊

➍

➌

➋

➎

1.75"

(45mm)

CROSSBRACE

Undercounter installation detail – Horizon 1000 & 1400 series

CAUTION

• Keep ventilation openings in the appliance enclosure clear of obstruction.

• To ensure proper ventilation (if not using supplied grille) carefully review air

circulation specications on facing page (4.1)

10 self-contained DROP-IN • SATELLITE-FILL

Ice transport tube

Install the ice transport tube. 5

208264

StockModuleIdentification Plate

ServiceNo.

ModuleNo.

Product

OMRESSORTHERMALLYPROTECTED

EastonPennsylvania

AMPS

VOLTSPHASE

SINGLE

CHARGE

LOWSIDE

PARTNO

PSIG

THEUSA

MADEIN

NSF

Hot Water

➎1/4˝

➊

➋

➌

➍

➏

➐

Ice transport tube tips

• Insulate entire length of ice transport tube ➊

• Secure ice transport tube ➋as needed to prevent dips and traps from forming.

For long tube runs see guide on page 16.

• Pitch tube at least 1/4" per foot (6,4mm/.3m) ➌

• Ice transport tube must drain towards icemaker

Ice transport tube to Icemaker

• Be sure tube ends are square ➍

• Soften ice transport tube with hot water (160 F (71 C)) to ease assembly ➎

• Push ice transport tube onto icemaker nipple ➏

• Install hose clamp ➐

Ice transport tube installation.

5.1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de hielo de Follett

Follett

Follett HCC1000A Manual de operación

Follett

Follett Horizon Elite series Manual de usuario

Follett

Follett H_C700AHS Manual de usuario

Follett

Follett Symphony 25HI400A Suplemento

Follett

Follett Horizon Elite series Manual de usuario

Follett

Follett HCD1400R Manual de operación

Follett

Follett HCD1650RBT Manual de usuario

Follett

Follett Horizon Elite H D710ABT Series Manual de usuario

Follett

Follett Horizon Elite 1010 Series Manual de usuario

Follett

Follett Horizon Elite 710 Series Manual de usuario

Follett

Follett Horizon HME1000ABT Manual de usuario

Follett

Follett HCD Manual de operación

Follett

Follett Horizon Elite 1410 Series Manual de operación

Follett

Follett Horizon Elite Chewblet HCF1010RMS Manual de usuario

Follett

Follett Maestro Manual de usuario

Follett

Follett Horizon Elite HC Series Manual de operación

Follett

Follett Horizon Elite HCD1410R Manual de usuario

Follett

Follett Horizon Elite Chewblet HCD1010RVS Manual de usuario

Follett

Follett T400A Guía de configuración

Follett

Follett HCE1000W Manual de operación

Follett

Follett HCD1000RBT Manual de usuario

Follett

Follett Horizon Elite HMF1010RJS Manual de usuario

Follett

Follett Horizon series Manual de usuario

Follett

Follett Horizon Elite HC-1810R/N Manual de operación

Manuales populares de Máquina de hielo de otras marcas

Hoshizaki

Hoshizaki KMD-460MWJ Manual de usuario

Sub-Zero

Sub-Zero 315I Instrucciones de uso

Unold

Unold 48945 Manual de usuario

Kenmore

Kenmore 2217402A Manual de usuario

Cornelius

Cornelius WM600 Instrucciones de funcionamiento

GE XPIO43SCSS Manual de usuario

Hoshizaki

Hoshizaki KMD-901MAH Manual de usuario

Whynter

Whynter FIM-450HA Manual de usuario

U-Line

U-Line UMCR014-SC01A Manual de instalación

Andrew James

Andrew James AJ000522 Manual de usuario

Scotsman

Scotsman CME1356 Manual de usuario

Scotsman

Scotsman ACM 25 Manual de usuario

Kärcher

Kärcher IP 120 Manual de usuario

U-Line

U-Line SS1095 Manual de usuario

Maytag

Maytag MIM1554WRS - Ice Maker Manual de usuario

Hoshizaki

Hoshizaki KM-630MAH Manual de usuario

Princess

Princess Yonanas Manual de usuario

Unold

Unold 48946 Manual de usuario