Follett Horizon series Manual de usuario
Order parts online
www.follettice.com
Horizon™Ice Machine Models with RIDE™Technology
Installation Instructions for Ice Manager™Diverter Valve
HCD/HCF1000RMS, HCD/HCF1400RMS, HCD/HCF1650RMS,
HCD1000NMS, HCD1400NMS, HCD1650NMS
(See model number congurator on page 2 for details.)
00172536R07
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Ice Manager
Diverter Valve
(1) Horizon™
Chewblet®Ice Machine
(purchased separately)
(2) ice storage units
(purchased separately)
Any combination of bins or dispensers
Ice Manager
Control Panel
Lane 1
Lane 2
remote condensing
2remote condensing ICE MANAGER
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
400 up to
454 lbs
(206kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro Chewblet
HC 1400CSVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations
3
ICE MANAGER remote condensing
Front cover
7
Internal connection
6
External connection
5
Louvered docking assembly
3
Site preparation
2
Unpack
1
After thorough review of Ice Manager site survey, read and complete
Horizon ice machine installation sections 1 through 6.
For connection to Ice Manager diverter valve system
refer to Ice Manager installation guide.
Horizon ice machine for use with Ice Manager diverter valve system
The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single Follett
Horizon ice machine to meet demand for ice at two locations. The system’s sensors monitor ice levels
in each storage unit and automatically switch ice delivery to the appropriate location.
Ice transport tube
4
4remote condensing ICE MANAGER
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
1/2"
1/2"
➊➋
➌➍
➎➏
Unpack ice machine
1. 1
5
ICE MANAGER remote condensing
➎
➍
3/8" ∅ (9,5mm)
NEMA
5-15
➌
➊
➍
1/4"
1'
➍
Prepare the installation site. 2
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
Electrical ➊
• 120/60/1-6 amps
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
Drain ➌
• The drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m)
Refrigeration lines ➍
• 1000, 1400: 5/8” (15,8mm) diameter suction (insulated) ➍
• 1650: 7/8” (22,2mm) diameter suction (insulated) ➍
• 3/8" (9,5mm) liquid ➎
Installation site requirements
2.1
6remote condensing ICE MANAGER
Install the louvered docking assembly.
Louvered docking assembly 3
• Mount louvered docking assembly ➊
• “Rough-in” the refrigerant piping ➋
2.1 Louvered docking assembly
3.1
• Mount louvered docking assembly to wall
bracket accessory
• Mount louvered docking assembly to
machine stand accessory
Wall bracket accessory Machine stand accessory
➊
➊
1" (25,4mm)
Stub Typ
3" (76mm)
1-3/4" (44,5mm)
3" (76mm)
3/8˝ ∅
high pressure
line
➋
1000, 1400:
5/8" ∅ low pressure line
1650:
7/8" ∅ low
p
ressure line
7
ICE MANAGER remote condensing
CROSSBRACE
21" min.
(534mm
24.5" min.
(623mm)
No Lip
➋
Top View
Access panel/
door on counter
1.75" (45mm) min.
➊
➌
DOCKING STATION
• Position and screw louvered docking assembly to the bottom of counter inside of access panel/
door min. of 1.75" (45mm) from the front edge of the cross brace ➊
• The mounting surface for the louvered docking assembly must be solid.
Do not mount directly onto runners or channels.
• There must be no lip or edge that would hinder the ice machine from sliding in or out of the
louvered docking station ➋
• Ice machine must be installed facing forward as shown for service accessibility ➌
Undercounter installation requirements
3.2
8remote condensing ICE MANAGER
Ice transport tube
Install the ice transport tube. 4
➎
➋➍
➏
➐
➊
1/4"
1'
➌
Hot Water
160 F (71 C)
Ice transport tube tips
• Insulate entire length of ice transport tube ➊
• Secure ice transport tube ➋as needed to prevent dips and traps from forming.
For long tube runs see guide on page 13.
• Pitch tube at least 1/4" per foot (6,4mm/.3m) ➌
• Ice transport tube must drain towards ice machine
Ice transport tube to Ice machine
• Be sure tube ends are square ➍
• Heat end of transport tube in cup of 160F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➏
• Install hose clamp ➐
Ice transport tube to diverter valve
• See Ice Manager diverter valve instructions
Ice transport tube installation.
4.1
9
ICE MANAGER remote condensing
Connect utilities to louvered docking assembly. 5
External connections
CAUTION
• Plug must be accessible after nal installation.
➋
➊
• Remove access panel if necessary.
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3m).
• Install ice machine potable water
supply ➋
• Replace access panel
Water and drain
5.1
➊
• Braze supplied expandable refrigerant
lines in place ➊
Refrigerant
5.2
10 remote condensing ICE MANAGER
Connect louvered docking assembly to ice machine. 6
Internal connections
➊
• Rotate and braze refrigerant lines ➊
Refrigeration lines
6.3
➊
➋
• Slide ice machine into louvered docking
assembly ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube installation
6.1
➊
➋
➊
➋
• Insert potable water line into valve ➊
• Push drain line over hose barb on
back of evaporator mount ➋
Water and drain lines
6.2
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
6.4
Este manual sirve para los siguientes modelos
9
Tabla de contenidos
Otros manuales de Máquina de hielo de Follett
Follett
Follett HMF1400R Manual de operación
Follett
Follett Horizon Elite HC-1810R/N Manual de operación
Follett
Follett Horizon Elite HCE710A Manual de operación
Follett
Follett R5A Manual de operación
Follett
Follett Horizon Elite HCD710AHS Manual de usuario
Follett
Follett Horizon Elite HCF1010R/N Manual de usuario
Follett
Follett MC-425A/W Guía de configuración
Follett
Follett Horizon Elite Chewblet HCD1410RBT Manual de usuario
Follett
Follett HCE Manual de operación
Follett
Follett C33984 Manual de operación
Follett
Follett Horizon Elite series Manual de usuario
Follett
Follett Horizon Elite 1410 Series Manual de operación
Follett
Follett Maestro Plus MC 414A Series Guía de configuración
Follett
Follett L60417 Manual de operación
Follett
Follett Horizon Elite HCD1010R/N Manual de operación
Follett
Follett HCC1400W Manual de operación
Follett
Follett E7CI100A Guía de configuración
Follett
Follett HCE1000W Manual de operación
Follett
Follett HCD1400N Manual de operación
Follett
Follett Horizon HMD700NHT Manual de usuario
