FLIR MR55 Manual de usuario

Quick Start

Pin Moisture Meter with

Bluetooth®

Model MR55

Quick Start

INTRODUCTION

The latest versions of the detailed User Manual and Quick Start,

with translations, are located on the http://support.flir.com web site

(download tab). Please read these documents carefully before use.

QUICK STEPS

1. Ensure that two fresh 1.5V ‘AA’ batteries are installed in the me-

ter’s rear compartment.

2. Long press the Power button to switch the meter ON. The

meter automatically switches OFF after 20 minutes (APO).

3. Short press the button to select a material group 1~11 (see

Measurement Considerations section).

4. Remove the protective cap and firmly insert the test pins into

the material under test.

5. Read the moisture level in %on the meter’s large display digits.

6. Read the ambient temperature or relative humidity on the small-

er digits. Long press the button to select ℉,℃, or RH

display.

7. Long press the button to switch the meter’s backlight ON/

OFF. Short press the button to switch the meter’s worklight

ON/OFF.

8. To freeze/unfreeze a displayed measurement, short press the

HOLD button.

9. To transmit a held reading, refer to the Bluetooth section below.

10. Replace the protective cap after each and use caution when the

sharp pins are exposed.

11. Verify calibration using the test points in the protective cap as

described in the User Manual.

#NAS100098; r. AB/80702/80849; en-US 1

METER DESCRIPTION

1. Temperature / RH sensors

2. Electrode pins

3. Backlit LCD

4. Data Hold / Transmit button

5. Worklight / Backlight button

6. Power ON-OFF button

7. Material group select and Temperature/RH button

8. Worklight

9. Battery compartment lock

10. Battery compartment

Note: Protective pin cap not pictured.

Note: QR code on back of meter provides website link to material

group information for wood and building materials.

#NAS100098; r. AB/80702/80849; en-US 2

FUNCTION BUTTONS

Long press to power the meter ON/OFF

HOLD Short press to freeze/unfreeze displayed readings (readings must

be held before they can be transmitted via Bluetooth)

Long press to transmit held reading to remotely connected device

using Bluetooth

Short press to switch worklight ON/OFF

Long press to switch display backlight ON/OFF

Short press to select a material group number (1~11)

Long press to select ambient temperature or relative humidity dis-

play on lower left of screen

DISPLAY DESCRIPTION

1. Bluetooth icon appears when meter is paired with remote

device

2. Transmission icon appears for 3 seconds while transmitting

3. Data Hold freezes displayed reading

4. Battery status

5. Material Group Number. Refer to User Manual for reference

tables

6. Moisture reading

7. Ambient temperature or Relative Humidity display

MEASUREMENT CONSIDERATIONS

• Moisture Measurement ranges:

#NAS100098; r. AB/80702/80849; en-US 3

Wood 7 to 99%

Building materials (Group 10) 1 to 99%

Building materials (Group 11) 1 to 35%

• Moisture readings are automatically temperature compensated

• When testing wood, always insert the pins perpendicular to the

wood’s fiber structure

• Take a number of readings in several locations for the best repre-

sentation of the moisture present

• Material Groups 1~8 are for timber; Group 9 is for plywood and

oriented strand board (OSB); Group 10 is for brick, cement

screed, and concrete; Group 11 is for cement mortar, anhydrite

screed, lime mortar, and plaster. Download the User Manual at

http://support.flir.com for complete details.

BLUETOOTH COMMUNICATION

When connected to a remote device running the FLIR Tools™ mo-

bile app, the MR55 (using the METERLiNK® protocol) can send

readings for display on the remote device. When connected to a

compatible FLIR camera that supports BLE (Bluetooth Low Energy),

the MR55 can send meter readings for display on the camera.

Download the FLIR Tools mobile app from the Google Play™ Store,

the Apple App store, or from here:

https://www.flir.com/products/flir-tools-app/

• When successful communication between the meter and a re-

mote device or FLIR camera is established, the Bluetooth icon

appears on the MR55 display.

• Refer to the FLIR Tools help utility (in the mobile app) for detailed

information regarding FLIR Tools.

• To transmit a displayed reading, first short press the MR55

HOLD button to freeze the reading (the ‘H’ icon appears) and

then long press the button to transmit.

• The transmission icon appears for 3 seconds during the trans-

mission of the moisture reading, material group number, and

temperature/humidity readings. Date/time stamp can be taken

from the remote device at the time of transfer.

• To unfreeze the displayed reading, short press the HOLD button

again (the ‘H’ icon will switch OFF).

#NAS100098; r. AB/80702/80849; en-US 4

Customer Support

Customer Support Telephone List: https://support.flir.com/contact

Repair, Calibration, and Technical Support https://support.flir.com

Three-Year Limited Warranty

This product is protected by FLIR’s 3-Year Limited Warranty. Visit

www.flir.com/testwarranty to read the 3-Year Limited Warranty

document.

#NAS100098; r. AB/80702/80849; en-US 5

last page

Publ. No.: NAS100098

Release: AB

Commit: 80702

Head: 80849

Language: en-US

Modified: 2021-11-02

Formatted: 2021-11-11

Website

http://www.flir.com

Customer support

http://support.flir.com

Disclaimer

Specifications subject to change without further notice. Models and accessories

subject to regional market considerations. License procedures may apply.

Products described herein may be subject to US Export Regulations. Please

refer to [email protected] with any questions.

Quick Start

Otros manuales para MR55

Tabla de contenidos

Otros manuales de Instrumento de medición de FLIR

FLIR

FLIR DM284 Manual de usuario

FLIR

FLIR Imaging Moisture Meter Plus IGM MR176 Manual de usuario

FLIR

FLIR Extech Instruments Oyster-10 Manual de usuario

FLIR

FLIR MR277 Manual de usuario

FLIR

FLIR VS80A2-45-1RM Manual de usuario

FLIR

FLIR Extech Instruments 480823 Manual de usuario

FLIR

FLIR Extech PQ3450-30 Manual de usuario

FLIR

FLIR CM85 Manual de usuario

FLIR

FLIR Extech Instruments EX840 Manual de usuario

FLIR

FLIR EXTECH INSTRUMENTS PQ34-12 Manual de usuario

FLIR

FLIR CM94 Manual de usuario

FLIR

FLIR EXTECH SDL310 Manual de usuario

FLIR

FLIR Extech 407760 Manual de usuario

FLIR

FLIR CM55 Manual de usuario

FLIR

FLIR TA72 Manual de usuario

FLIR

FLIR Extech Instruments EN300 Manual de usuario

FLIR

FLIR VS80A4-60-2RM Manual de usuario

FLIR

FLIR VS80 KIT Manual de usuario

FLIR

FLIR CM83 Manual de usuario

FLIR

FLIR CM55 Manual de usuario

FLIR

FLIR CM57-2 Manual de usuario

FLIR

FLIR MR55 Manual de usuario

FLIR

FLIR MR265 Manual de usuario

FLIR

FLIR identiFINDER R300 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario