FLIR VS80 KIT Manual de usuario

Quick Start

VS80 KIT

High Performance Videoscope and

Camera Probe

Quick Start (en)

INTRODUCTION

The VS80 kit consists of the main display unit, a camera probe, and

accessories. To obtain the comprehensive user manual, additional

quick start translations, firmware updates, and customer support,

see the Support section. Please upgrade the firmware before use

for optimal performance and camera compatibility.

The numbers in parenthesis, below, refer to the items listed in the

Product Description section.

QUICK STEPS

1. Insert micro SD card in slot located in side compartment (19).

2. Connect the camera probe (16):

3. Remove the camera’s protective lens cap.

4. Long press the power button (9), the FLIR logo will appear.

5. The camera image will then appear (14) with touch-screen

icons (12) bordering the image.

6. For the IR camera only, the dot on the probe head indicates the

top of the image, as shown:

7. If the battery icon (15) indicates a low charge, connect the sup-

plied AC adapter to the USB port at the top of the display unit

(17) and to an AC power source (100 to 240 VAC, 50/60 Hz).

8. The status LED (1) is blue when power is on (charger not con-

nected); green when charging with power off; cyan (light blue)

when charging with power on; no light when fully charged (with

charger attached).

9. Long press the power button (9) to switch off the VS80.

#NAS100100; r. AC/83794/84876; en-US 1

PRODUCT DESCRIPTION

1. Power status LED

2. Image capture button

3. Video recording start/stop button

4. 1. Full screen view button; 2. Disconnect Wi-Fi

5. Zoom in (navigate upward in touch-screen menus)

6. Zoom out (navigate downward in touch-screen menus)

7. Decrease brightness (move left in touch-screen menus)

8. Increase brightness (move right in touch screen menus)

9. Long press to power on/off. Short press to return from a menu

10. Settings menu button

11. Image/video gallery button

12. Touch screen icons

13. Temperature scale (IR only)

14. Camera images and menus

15. Battery status icon

16. Probe connection

17. PC interface/charger USB-C port

18. Neck and hand strap fasteners

19. Compartment for reset button, SD card, HDMI port

20. Microphone connector (3.5 mm)

Tilt stand, tripod mount (back of unit), and sun visor are not

pictured.

#NAS100100; r. AC/83794/84876; en-US 2

SETTINGS MENU

Press the Settings button to open or close the menu. The menu

has two pages, tap the up/down (∆ ∇) touch-screen arrows to scroll.

Tap an item to open it or to enable/disable it.

Menu items are briefly described below. For complete information,

please refer to the online user manual.

Wi-Fi Switch Wi-Fi on/off, set password (settings

icon), and view the SSID.

DISPLAY GRID Enable/disable the display measurement grid.

Digital cameras only

TIMESTAMP Enable to include date and time with recorded

images and video.

EXTERNAL MICROPHONE Enable microphone to record voice-overs on-

to video.

USB CARD READER Connect to a PC via USB to share images/

video and to update firmware (INFO menu).

SD CARD View memory status, format card, and delete

all images/video.

IMAGE Set display brightness, contrast, and sharp-

ness. Digital cameras only

MEASUREMENT

PARAMETERS

Set emissivity, reflected temperature, and

temperature units. IR camera only

AUTO POWER OFF Disable or set to 5, 10, 20, or 30 minutes.

DATE / TIME Set and format the calendar clock.

LANGUAGE Select local language.

RECORDING QUALITY

(VIDEO)

Set to Normal (1 M bits/s) or High Quality (2

M bits/s). Digital cameras only

PROBE SELECTION Select the probe that you are using from the

list. Digital cameras only

#NAS100100; r. AC/83794/84876; en-US 3

INFO View firmware version, upgrade firmware, and

revert settings to factory default.

ASPECT RATIO IR camera only. Toggle 4:3 and 16:9 display

formats.

DIGITAL CAMERA TOUCH SCREEN ICONS

Tap an icon to enable/disable it or to open its submenu. Refer to the

probe’s user manual for more information.

Switch the exposure com-

pensation filter on/off

(brightens dark areas).

Switch dust elimination filter

on/off. For use with mirror

accessories and dual cam-

era model.

Switch worklight on/off.

Forward/side view split

screen. For use with mirror

accessories and dual

cameras.

Switch the mirror image

on/off.

Change the direction of the

worklight (side/forward)

when using mirror accesso-

ries or dual camera.

Opens the image gallery.

Select an image to com-

pare with the live image

on a split-screen.

Switch the image negative

on/off.

Rotate image clockwise

(90°, 180°, 270°). Set the white balance.

IR CAMERA TOUCH SCREEN ICONS

Tap an icon to open its submenu. See the probe user manual for

more information.

Rotate image clockwise (90°, 180°, 270°) or view mirror image.

Select color palette (Iron, Rainbow, Gray) or alarm mode (Above

alarm, Below alarm).

Tap to open the Measurement submenu for Center Spot, Cold Spot,

Hot Spot, and No Measurement modes, explained below.

#NAS100100; r. AC/83794/84876; en-US 4

Center spot: Temperature of spot is displayed on upper left.

The coldest (cyan cross-hairs) or hottest (red cross-hairs) spot is

targeted in the boxed region of the image. The spot temperature is

shown on the upper left side of the display.

Tap and drag the box to move it, use the navigation buttons (up [5],

down [6], left [7], right [8]) to re-size it, or pinch/stretch the box with

two fingers to narrow or widen it.

No Measurements: Temperature is not measured.

Temperature Scale. Use Auto (A) in normal operation; Use Manual

(M) to limit the temperature range, based on the temperature of the

targeted spot.

Measurement parameters: Set emissivity, reflected temperature,

and temperature units.

ABOVE AND BELOW ALARMS (IR CAMERA)

To set an alarm, tap the palette icon and select the Above or

the Below alarm.

In Above alarm mode, the camera will apply a red color to all parts

of the image with a temperature above the alarm set point. In Below

alarm mode, the camera will apply a blue color to all parts of the im-

age with a temperature below the alarm set point.

Tap and drag the color bar graph to adjust the set point.

CUSTOMER SUPPORT

The FLIR support site, address below, is your resource for obtaining

firmware upgrade files, latest versions of user manuals, customer

service, and other product and accessory information.

https://support.flir.com

Three-Year Limited Warranty

This product is protected by FLIR’s 3-Year Limited Warranty. Visit

www.flir.com/testwarranty to read the 3-Year Limited Warranty

document.

#NAS100100; r. AC/83794/84876; en-US 5

last page

Publ. No.: NAS100100

Release: AC

Commit: 83794

Head: 84876

Language: en-US

Modified: 2022-03-08

Formatted: 2022-05-06

Website

http://www.flir.com

Customer support

http://support.flir.com

Disclaimer

Specifications subject to change without further notice. Models and accessories

subject to regional market considerations. License procedures may apply.

Products described herein may be subject to US Export Regulations. Please

refer to [email protected] with any questions.

Quick Start

Tabla de contenidos

Otros manuales de Instrumento de medición de FLIR

FLIR

FLIR MR277 Manual de usuario

FLIR

FLIR MR59 Manual del operador

FLIR

FLIR CM174 Manual de usuario

FLIR

FLIR EXTECH MA620 Manual de usuario

FLIR

FLIR MR59 Manual de usuario

FLIR

FLIR Imaging Moisture Meter Plus IGM MR176 Manual de usuario

FLIR

FLIR identiFINDER R200 Manual de usuario

FLIR

FLIR CM72 Manual de usuario

FLIR

FLIR Extech 380941 Manual de usuario

FLIR

FLIR Si124 Manual de usuario

FLIR

FLIR MR265 Manual de usuario

FLIR

FLIR IGM CM275 Manual de usuario

FLIR

FLIR CM57-2 Manual de usuario

FLIR

FLIR Extech 407760 Manual de usuario

FLIR

FLIR EM54 Manual de usuario

FLIR

FLIR Extech 380926 Manual de usuario

FLIR

FLIR EXTECH SDL310 Manual de usuario

FLIR

FLIR VS80A4-60-2RM Manual de usuario

FLIR

FLIR CM82 Manual de usuario

FLIR

FLIR Extech PQ3450-30 Manual de usuario

FLIR

FLIR CM83 Manual de usuario

FLIR

FLIR CM85 Manual de usuario

FLIR

FLIR MR176 Manual de usuario

FLIR

FLIR Extech Instruments RH520A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario