FLIR Extech 380941 Manual de usuario

User Guide

AC/DC Mini Clamp Meter

Model 380941

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380941-EN-V3.2-3/12

Introduction

Congratulations on your purchase of Extech’s DC/AC Clamp Meter. This professional meter, with

proper care, will provide years of safe reliable service.

Front Panel Description

1. Current sense jaw

2. Measurement Trigger

3. Function switch

4. Data Hold key

5. Max Min key

6. One-touch DCA zero key

7. LCD Display

8. 40 segment bargraph display

9. Positive input terminal for V, HZ and Ω

10. COM terminal

International Symbols

!Caution ! Refer to the explanation in this Manual

Caution ! Risk of electric shock

Earth (Ground)

Safety

This meter has been designed to be safe in use, but the operator must use caution in its operation.

The rules listed below should be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified maximum:

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 500V above earth

ground.

4. NEVER connect the meter leads across a voltage source while the function switch is in the

current, resistance or diode mode; doing so can damage the meter.

5. ALWAYS discharge filter capacitors in power supplies and disconnect the power when making

resistance or diode tests.

6. ALWAYS turn off the power and disconnect the test leads before opening the back to replace

the fuse or batteries.

7. NEVER operate the meter unless the back cover and the battery/fuse door are in place and

fastened securely.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380941-EN-V3.2-3/12

Operation

AC Current Measurements

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the 40 or 200A AC range.

2) Press the jaw trigger and clamp around, fully enclosing a single conductor. Do not allow a gap between the

two halves of the jaw.

3) Read the ACA value on the LCD.

DC Current Measurements

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the 40 or 200A DC range.

2) Press the DCA zero key to null the meter display.

3) Press the Trigger to open the current sense Jaw.

4) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of

the jaw.

5) Read the DCA value on the LCD.

AC Voltage Measurements

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified.

1) Set the Function switch to the VAC position.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,Ω” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure voltage. Remember that voltage

measurements are made in parallel with the device or circuit under test.

4) Read the ACV value on the LCD.

DC Voltage Measurements

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified.

1) Set the Function switch to the VDC position.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,Ω” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure voltage. Remember that voltage

measurements are made in parallel with the device or circuit under test.

4) Read the DCV value on the LCD.

Resistance and Continuity Measurements

WARNING: To avoid electric shock or damage to the meter, remove power to the circuit under test and discharge

all capacitors.

1) Set the Function switch to the Ωposition.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,Ω” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure resistance. Remember that resistance

measurements are made in parallel with the device or circuit under test.

4) Read the resistance value on the LCD.

5) If the resistance is less than 40Ω, the continuity beeper will sound.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380941-EN-V3.2-3/12

Frequency Measurements

1) Ensure that at least 0.1A AC is detectable with an ACA measurement before measuring

Frequency.

2) Set the Function switch to the Hz position.

3) Insert the test leads to the meter as follows: Red lead to “V,Hz,Ω” terminal; Black lead to the

COM input.

4) With the pointed end of the test leads measure frequency

5) Read the Frequency measurement on the LCD in Hz.

Additional Features

Relative Measurements

1) Press the Zero key and the present measurement will Zero.

2) All subsequent measurements are displayed with respect to the zeroed reading. For example,

if a 20A reading is zeroed and a 30A reading is subsequently measured, the LCD will display

10A.

3) To return to normal operation, press and hold the zero key for 2 seconds.

4) Note that Relative mode is not available if the MIN/MAX mode is enabled.

Data Hold

To freeze a reading on the LCD, press the Data Hold key. The HOLD icon will appear and the

measurement will be held on the meter’s LCD. To release the Data Hold function and return the

meter to normal operation, press the Data Hold key again.

MIN/MAX Reading Mode

Pressing the MIN/MAX key allows the meter to display ONLY the highest and the lowest readings

encountered. Press the MIN/MAX key once to view the minimum reading, press it again to view

the maximum reading. Note that the meter will only change its displayed reading when a

measurement higher than the previous MAX or lower than the previous MIN readings is

encountered. The HOLD display icon (along with the MIN or MAX icon) will appear on the LCD in

MIN/MAX mode. Pressing the MIN/MAX key a 3rd time returns the meter to normal operation.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380941-EN-V3.2-3/12

Specifications

General Specifications

Display 3-3/4 (4000 count) Digit LCD with 40 segment bargraph

Functions ACA, DCA, ACV, DCV, Resistance, Frequency, Continuity

Polarity “-“ indicates negative polarity

Current sensor Hall effect sensor type

Overload indication Left blinking digit

DCA zero adjust One touch zero key

Display rate 2 readings/second (20 readings/second for bargraph)

Battery Two 1.5V AA batteries

Operating

temperature

4oF to 122oF (-10oC to 50oC)

Operating humidity < 85% RH

Power

consumption

Approximately 10mA DC

Weight 8 oz. (225g) including battery

Dimensions 7 x 1.75 x 1.25” (178 x 45 x 32mm) (HWD)

Jaw opening 0.9” (23mm)

Standards IEC 1010 Category III 300V, Category II 600V

Range Specifications

Function Range Resolution. Accuracy Overload

protect

40A 10mA ±(1.0% +2dgts) 400A DC

0 to 150A 100mA ±(1.0% +2dgts) 400A DC

DC Current

150 to 200A 100mA ±(2.2% +2dgts) 400A DC

50/60Hz 40 to 400Hz

40A 10mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC

0 to 150A 100mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC

AC Current

150 to 200A 100mA ±(2.2% +3dgts) ±(2.5% ±4dgts) 400A AC

DC Voltage 400V 0.1V ±(1.0% +2dgts) 1000VDC

50/60Hz 40 to 400HzAC Voltage

400V 0.1V ±(1.5% +2dgts) ±(2.0% +4dgts) 800V AC

Resistance 40 to 400Ω0.1 ±(1.0% +2dgts)

Beeper <38Ω600V AC

Frequency 100 to 10k 0.01Hz ±0.5% ±2dgts Sensitivity;

2V, 0.1A AC

600V AC

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Maintenance

Battery Replacement

1) When the low battery symbol appears on the LCD the batteries must be replaced.

2) Turn the meter off and remove the rear battery compartment screw.

3) Remove the battery compartment cover and replace the two 1.5V AA cells.

4) Replace the compartment cover and secure the screw.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries /

accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Cleaning

Caution: Use only a dry cloth to clean the plastic case.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Tabla de contenidos

Otros manuales de Instrumento de medición de FLIR

FLIR

FLIR EXTECH INSTRUMENTS PQ3450 Manual de usuario

FLIR

FLIR CM174 Manual de usuario

FLIR

FLIR CM78 Manual de usuario

FLIR

FLIR Extech Instruments MA410 Manual de usuario

FLIR

FLIR TA72 Manual de usuario

FLIR

FLIR Extech EX612 Manual de usuario

FLIR

FLIR Extech Instruments EX840 Manual de usuario

FLIR

FLIR Extech 407760 Manual de usuario

FLIR

FLIR identiFINDER R200 Manual de usuario

FLIR

FLIR DM284 Manual de usuario

FLIR

FLIR CM174 Manual de usuario

FLIR

FLIR identiFINDER R300 Manual de usuario

FLIR

FLIR DM284 Manual de usuario

FLIR

FLIR CM42 Manual de usuario

FLIR

FLIR EXTECH SDL310 Manual de usuario

FLIR

FLIR CM57-2 Manual de usuario

FLIR

FLIR IMAGING MOISTURE METER with IGM MR160 Manual de usuario

FLIR

FLIR CM85 Manual de usuario

FLIR

FLIR EM54 Manual de usuario

FLIR

FLIR Extech Instruments Oyster-10 Manual de usuario

FLIR

FLIR Imaging Moisture Meter Plus IGM MR176 Manual de usuario

FLIR

FLIR Extech Instruments MA1500 Manual de usuario

FLIR

FLIR CM72 Manual de usuario

FLIR

FLIR MR55 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario