Flashforge Adventurer 3 Pro 2 Manual de usuario

This guide is only applicable to FLASHFORGE Adventurer 3 Pro 2 3D Printer.

EN-A03 Adventurer 3 Pro 2

Scan the QR code to view

the unboxing video.

1.1 - Components Introduction

1.2 - Parameters

2.1 - Unpacking

2.2 - Accessories

2.3 - PEI Build Plate Installation

2.4 - Printing

2.4.1 - Software Installation

2.4.2 - Equipment Preparation

2.4.2.1 - Leveling and Calibration

2.4.2.2 - Flilament Loading

2.4.3 - Model File Transfer

2.4.4 - Printing

2.4.4.1 - FlashCloud Printing

2.4.4.2 - Polar Cloud Printing

2.4.5 - Model Removal

2.4.6 - Filament Change

2.5 - User Interface Introduction

2.5.1 - Build

2.5.2 - Tools

2.5.2.1 - Network

2.5.2.2 - Preheat

2.5.2.3 - Setting

2.5.2.4 - About

2.5.3 - Filament

2.6 - Camera Instructions

2.6.1 - FlashCloud Camera Use

2.6.2 - Polar Cloud Camera Use

2.6.3 - Cloud-Based Camera Control

2.6.4 - Error Handling

Chapter 1: Adventurer 3 Pro 2

Chapter 2: Operating

Chapter 3: Q&A

Chapter 4: Help and Support

CONTENTS

Preface

Notice

Terms

Note: Each device must be tested before leaving the factory. If there are some residues in

the extruder or some tiny scratches on the build tape, it is normal and won’t aﬀect

the printing quality.

On the completion of this User Guide, thanks all Flashforge engineers and Flashforge 3D

printer users for their unremitting eﬀorts and sincere assistance.

The Flashforge Adventurer 3 Pro 2 user guide is designed for users to start their printing

journey with Flashforge Adventurer 3 Pro 2. Even if you are familiar with earlier Flashforge

machines or 3D printing technology, we still recommend you to read this guide, as there is

lots of important information about the Adventurer 3 Pro 2 for you to get a better 3D

experience.

For a better and more successful printing experience, you can refer to the following materials:

Quick Start Guide:

Users will ﬁnd the Quick Start Guide together with the printer accessories. The Quick Start Guide

will help you start your print journey as soon as possible.

Oﬃcial Flashforge Website: www.ﬂashforge.com

The oﬃcial Flashforge website contains the up-to-date information concerning Flashforge

software, ﬁrmware, device maintenance and so on. Users are also able to get the contact

information from there.

Preface

Work Environment Safety

Electrical Safety

Personal Safety

Cautions

Keep your work place tidy.

Do not operate the printer in the presence of ﬂammable liquids, gases or dust.

Keep the printer out of children and untrained people’s reach.

Always use the printer with a properly grounded outlet. Do not reﬁt Adventurer 3 Pro 2 plug.

Do not use the printer in damp or wet locations. Do not expose the printer to burning sun.

In case of device damage, please use the power cord provided by Flashforge.

Avoid using the device during an thunderstorm.

In case of uncertain accident, please unplug the device if you do not use it for long.

Do not touch the nozzle and build plate during printing.

Do not touch the nozzle after ﬁnishing printing.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves

away from moving parts.

Do not operate the device while you are tired or under the inﬂuence of drugs, alcohol or

medication.

Do not leave the device unattended for long.

Do not make any modiﬁcations to the device.

Lower the build plate before loading/unloading ﬁlament.

[The distance between the nozzle and build plate should be kept for at least 50mm.]

Operate the device in a well-ventilated environment.

Never use the device for illegal activities.

Never use the device to make any food containers.

Never use the device to make any electrical appliance.

Never put the model into your mouth.

Do not remove the models with brute force.

Safety Notice: PLEASE READ AND STRICTLY FOLLOW ALL THE

SAFETY WARNINGS AND NOTICE BELOW.

Notice

Operating Environment Requirements

Equipment Placement Requirements

Filament Requirements

Filament Storage

Legal Notice

Temperature: RT 15-30 ℃; Moisture: 20%-70%

The device must be placed in a dry and ventilated environment.

The distances of the left, right and back side space should be at least 20cm, and

the distance of the front side space should be at least 35cm. Device storage

temperature: RT 0-40 ℃

Please make sure you use the Flashforge ﬁlament or the ﬁlament from the brands

accepted by Flashforge.

Nozzle clogging and damage may be caused by non-Flashforge ﬁlament due to

inappropriate material properties.

All the information in this document is subject to any amendment or change without

the oﬃcial authorization from Flashforge.

Flashforge makes no warranty of any kind with regard to this document, including,

but not limited to, the implied warranties of merchantability and ﬁtness for a particular

purpose.

Flashforge shall not be liable for errors contained herein for incidental consequential

damages in connection with furnishing, performance or use of this material.

This document contains proprietary information protected by copyright.

All polymers degrade with time. Do not unpack the ﬁlament unless it is required for use.

Please keep the storage environment dry and dust-free.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment oﬀ and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver

is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

The surface on which the Adventurer 3 Pro 2 builds an object

Build Tape

Build Plate

The black tape that covers Adventurer 3 Pro 2’s build plate so

that the object can stick to the build plate well

Build Volume The dimensions of the space into which 3D prints can be

produced. The largest build volume is 150*150*150mm.

Extruder

Nozzle

Cooling Fan

Filament Cartridge

Filament Guide Tube

Filament Intake

Solid Glue Stick

The integral extruder assembly is installed on X-axis.

The extruder draws the ﬁlament from the ﬁlament spool,

melts it and extrudes it through the nozzle into the build plate.

Also called ‘print head’, which is located at the bottom

of the extruder where heated ﬁlament is squeezed out.

A speciﬁc box for placing Flashforge ﬁlament, which is

located on the right of the printer.

A white plastic tube that guides the ﬁlament from the

ﬁlament box to the ﬁlament intake

A solid adhesive used for making the model stick to the

build plate ﬁrmly

To cool the outer assembly of the extruder and gear motor

An opening located at the top of the extruder

Terms

1.1 Components Introduction

1. Filament guide tube 2. Filament guide tube joint 3. Extruder base 4. Cooling fan

5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light 9. Air guide duct

10. Front door 11. Y-axis sliding slot 12. Platform base 13. Build plate

14. Touch screen 15. USB stick input 16. Power switch 17. Power input

18. Spool holder 19. Filament cover 20. Filament cover handle

21. Motor 22. Filament intake 23. Filament feeding wheel 24. Top cover

25. Air outlet 26 Ethernet input

Chapter 1: Adventurer 3 Pro 2

1.2 Parameters

Name

Number of Extruder

Print Technology

Screen Size

Build Volume

Layer Thickness

Build Accuracy

Positioning Accuracy

Filament Diameter

Nozzle Diameter

Build Speed

Software

Supported Formats

Memory Size

Input

Connectivity

Device Size

Net Weight

Adventurer 3 Pro 2

1, Removable

Fused Filament Fabrication [FFF]

2.8”color Touch Screen

150*150*150 mm

0.1-0.4 mm

± 0.2 mm

Z-axis 0.0025mm; XY-axis 0.011 mm

1.75 mm [± 0.07 mm]

0.4 mm

10-300 mm/s

FlashPrint

Input: 3mf/stl/obj/fpp/bmp/png/jpg/jpeg File

Output: gx/g File

8 G

Windows XP/Vista/7/8/10, Mac OS, Linux

150W [24V, 6.25A]

USB, Wi-Fi, Ethernet

388*340*405 mm

9 kg

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de Flashforge

Flashforge

Flashforge DREAMER Manual de usuario

Flashforge

Flashforge Guider 3 Plus Manual de usuario

Flashforge

Flashforge Creator Manual de instrucciones

Flashforge

Flashforge Guider 2 Manual de usuario

Flashforge

Flashforge DREAMER Manual de usuario

Flashforge

Flashforge ADVENTURER 3 Manual de usuario

Flashforge

Flashforge Hunter Manual de usuario

Flashforge

Flashforge Creator 3 Manual de usuario

Flashforge

Flashforge DREAMER Manual de usuario

Flashforge

Flashforge Adventurer 5M Manual de usuario

Flashforge

Flashforge CN/EN-A01 Manual de usuario

Flashforge

Flashforge Adventurer 5M Pro Manual de usuario

Flashforge

Flashforge Adventurer 4 Pro Manual de usuario

Flashforge

Flashforge Creator Pro Manual de usuario

Flashforge

Flashforge Creator 3 Manual de usuario

Flashforge

Flashforge Creator 3 Manual de usuario

Flashforge

Flashforge Finder 3 Manual de usuario

Flashforge

Flashforge Inventor 2 Manual de usuario

Flashforge

Flashforge ADVENTURER 3 V2 Manual de usuario

Flashforge

Flashforge Adventurer 4 Manual de usuario

Flashforge

Flashforge Creator Pro Manual de usuario

Flashforge

Flashforge Creator Pro Manual de usuario

Flashforge

Flashforge Finder Manual de usuario

Flashforge

Flashforge Guider 3 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario