Festo CPX-FVDA-P Instrucciones de funcionamiento e instalación
Description
Output module
CPX-FVDA-P
with
connection block
CPX-M-AB-4-M12X2
-5POLE
and
interlinking block
CPX-M-GE-EV-FVO
570844
en 1303a
[8023314]
CPX terminal
Output module CPX-FVDA-P
Contents and general instructions
I
Festo P.BE-CPX-FVDA-P-EN en 1303a English
Translation of the original instructions
Original de.......................................
Version en 1303a..................................
Designation P.BE-CPX-FVDA-P-EN.....................
Order number 570844..............................
E(Festo AG & Co., 73726 Esslingen, Germany, 2013)
Internet: http://www.festo.com
E-Mail: service_international@festo.com
Reproduction, distribution or sale of this document or com-
munication of its contents to others without express author-
ization is prohibited. Offenders will be liable for damages.
All rights reserved in the event that a patent, utility model or
design patent is registered.
Contents and general instructions
II
Festo P.BE-CPX-FVDA-P-EN en 1303a English
PROFINET IO
®
,PROFIBUS
®
are registered trademarks of
the respective trademark owners in certain countries.
Contents and general instructions
III
Festo P.BE-CPX-FVDA-P-EN en 1303a English
Table of contents
Important user instructions VI..............................................
General safety instructions VIII...............................................
Intended use VIII..........................................................
Possible incorrect application XI............................................
Attainable safety level XIII...................................................
Requirements for product use XIII............................................
Failures due to common cause (common cause failure – CCF) XV..................
Service XV...............................................................
Range of application and certifications XVI.....................................
Product identification XVII...................................................
Transport and storage conditions XX.........................................
Instructions on this description XXI...........................................
Product specific terms and abbreviations XXII...................................
1. System overview CPX-FVDA-P 1-1....................................
1.1 CPX terminal with output module CPX-FVDA-P 1-3.......................
1.1.1 Design of the output module CPX-FVDA-P 1-6....................
1.1.2 Supported product designs from CPX 1-10.......................
1.1.3 Required bus topology (control loop system) 1-11.................
1.2 Addressing 1-13....................................................
1.2.1 Bit pattern of the output and input data (F-user data) 1-14..........
1.3 Mode of operation of the output module 1-19............................
1.3.1 Application ranges (examples) 1-20.............................
1.4 Requirements for actuators (CH0 ... CH2) 1-23............................
2. Installation 2-1...................................................
2.1 General instructions on installation 2-3................................
2.2 Connecting the cables and plugs to the connection block 2-3..............
2.3 Electrical connection and display components 2-5.......................
2.3.1 Pin allocation with M12 connection block 2-6....................
Contents and general instructions
IV
Festo P.BE-CPX-FVDA-P-EN en 1303a English
3. Commissioning 3-1................................................
3.1 General instructions 3-3.............................................
3.2 Commissioning 3-5.................................................
3.2.1 Preparing for commissioning 3-5..............................
3.2.2 Set PROFIsafe address 3-5...................................
3.2.3 Commissioning steps 3-8....................................
3.3 Set PROFIsafe parameter of the output module CPX-FVDA-P 3-9............
3.4 CPX module parameter of the output module CPX-FVDA-P 3-10..............
3.4.1 CPX module parameters CPX-FVDA-P in detail 3-12................
3.4.2 Parameterisation and signal display with the handheld (MMI) 3-16...
3.5 Notes on operation 3-18..............................................
3.5.1 Start behaviour of the output module 3-18.......................
3.5.2 Reaction to faults 3-18........................................
3.6 Configuration with Siemens STEP 7 (example). 3-19.......................
3.6.1 Addressing example 3-23.....................................
4. Diagnostics and error handling 4-1...................................
4.1 Summary of diagnostics options 4-3...................................
4.2 Possible error messages of the output module CPX-FVDA-P 4-4............
4.3 Diagnostics via LEDs 4-6............................................
4.3.1 Error handling and parameterisation 4-9........................
4.3.2 Behaviour during the switch-on phase (startup phase) 4-11.........
4.3.3 Normal operating status 4-11..................................
4.3.4 Behaviour in the event of an error 4-12..........................
4.4 Diagnostics via the CPX bus node 4-13..................................
4.4.1 Diagnostics with the handheld CPX-MMI 4-13.....................
5. Dismantling, assembly, repair and disposal 5-1........................
5.1 General instructions 5-3.............................................
5.2 Dismounting and mounting the electronics module 5-5...................
5.3 Repair 5-7........................................................
5.4 Disposal 5-7......................................................
Contents and general instructions
V
Festo P.BE-CPX-FVDA-P-EN en 1303a English
A. Technical appendix A-1.............................................
A.1 Technical data for output module CPX-FVDA-P A-3.......................
A.2 Technical data of the connection block A-7..............................
A.3 Technical data - interlinking block A-8..................................
B. Index B-1.........................................................
B.1 Index B-3.........................................................
Contents and general instructions
VI
Festo P.BE-CPX-FVDA-P-EN en 1303a English
Important user instructions
Danger categories
This description includes instructions on the possible dangers
which can occur if the product is used incorrectly. These in-
structions are marked with a signal word (Warning, Caution,
etc.), printed on a shaded background and marked addition-
ally with a pictogram. A distinction is made between the fol-
lowing danger warnings:
Warning
... means that failure to observe this instruction may result
in serious personal injury or material damage.
Caution
... means that failure to observe this instruction may result
in personal injury or material damage.
Note
... means that failure to observe this instruction may result
in material damage.
In addition, the following pictogram marks passages in the
text which describe activities with electrostatically sensitive
devices:
Electrostatically sensitive devices: Incorrect handling may
cause damage to devices.
Contents and general instructions
VII
Festo P.BE-CPX-FVDA-P-EN en 1303a English
Marking of special information
The following pictograms mark passages in the text which
contain special information.
Pictograms
Information:
Recommendations, tips and references to other information
sources.
Accessories:
Specifications on necessary or useful accessories for the
Festo product.
Environment:
Information on the environmentally friendly use of Festo
products.
Text designations
•
Bullets denote activities that may be carried out in any
desired order.
1. Numerals denote activities that must be carried out in the
sequence specified.
– Arrowheads indicate general lists.
Contents and general instructions
VIII
Festo P.BE-CPX-FVDA-P-EN en 1303a English
General safety instructions
Warning
Nonobservance of safety regulations can result in death,
serious injuries or high material damage.
•
Ensure to comply with the safety regulations.
Note
Electronic modules include electrostatically sensitive
devices. Incorrect handling can cause damage to the elec-
tronics modules.
•
Observe the handling specifications for electrostatically
sensitive devices.
•
Discharge yourself from static discharges before in-
stalling or disassembling modules to protect the mod-
ules.
Observe the regulations for the electrical supply of CPX ter-
minals in the CPX system description (Protective Extra-Low
Voltage, PELV).
Intended use
The module can be used as intended to achieve the safety
function
– Safe shut off of connected consumers
if in the off state the connected consumers go into the safe
state.
Otros manuales para CPX-FVDA-P
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Unidad de control de Festo
Festo
Festo CPX-AP-A-8DO-M12-5P Manual de usuario
Festo
Festo CPX-E-EP Manual de usuario
Festo
Festo HEM Series Manual de instrucciones
Festo
Festo CPV-DI02 Manual de lista de piezas
Festo
Festo PREL-186 Manual de usuario
Festo
Festo MS9-SV-10V24P Manual de usuario
Festo
Festo CDSV5.0 Series Manual de usuario
Festo
Festo CPX-M-FB20 Manual de lista de piezas
Festo
Festo EFSD Manual de usuario
Festo
Festo CPE PRS Series Manual de usuario
Festo
Festo CPX-E-EC Manual de usuario
Festo
Festo VOFA-L26-T52-M Series Manual de usuario
Festo
Festo CPX-4AE-4AA-H Instrucciones de funcionamiento e instalación
Festo
Festo CP-FB13-E Manual de lista de piezas
Festo
Festo MSE6-C2M Manual de lista de piezas
Festo
Festo CDVI Series Manual de lista de piezas
Festo
Festo VIFB13 Series Manual de usuario
Festo
Festo MS6 SV E 10V24 Series Manual de usuario
Festo
Festo CP-FB11-E Manual de lista de piezas
Festo
Festo FSSC-12 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
KHADAS
KHADAS BT Magic Manual de usuario
