FELIXprinters Tec 4 Manual de usuario

Quick Start Guide

Tec 4

www.felixprinters.com/support

[email protected]

Zeemanlaan 15

3401 MV IJsselstein

The Netherlands

FELIXprinters Quick Start Guide for the FELIX Tec 4

General safety

Keep children under the age of 14 out of reach of the printer.

FELIXprinters are only suitable for professional use.

Considerations when in operation

Do not lean on the printer.

Be careful with long hair and loose clothes.

Do not transport the printer while working.

Make sure all moving parts can move without any obstructions.

Do not remove any objects from the hot plate while printing.

Caution with any moving parts that move in the X, Y and Z

direction. At the end of each moving part there is a pinching

hazard.

Electronic safety

Only use the power supplies and cables supplied by FELIX-

printers. Always turn off and unplug the printer before doing

maintenance or modications.

The power supply meets all CE mark regulations and is

protected against short-circuit, overload, over voltage and over

temperature.

Printer placement

Place the FELIXprinter on a stable table/desk.

This will keep it safe from small children.

Use the FELIXprinter in a dry environment.

Ventilate

Good ventilation while printing is advised though printing

pure PLA is considered safe. When printing ABS, small

concentrations of Styrene vapour can be released. This

can (in some cases) cause headaches, fatigue, dizziness,

confusion, drowsiness, malaise, difculty in concentrating,

and a feeling of intoxication.

We recommend using lament types shown on the FELIX-

printers website. Examples PLA, PETG, ABS, PVA etc. Other

types may be toxic. Please follow instructions from the

lament supplier.

Caution with heater elements

There is a potential risk of injury, as the print head can reach

temperatures of up to 275°C and the heated bed of up to

100°C. Don’t place objects on the heated bed that are not

being printed, not even when the printer is turned off.

We do not recommend to leave the printer unattended for

a very long period of time. If you do, it is recommended to

leave it in a properly conditioned room with distance from

highly amable objects.

Safety

Page 2

FELIXprinters Quick Start Guide for the FELIX Tec 4

Thank you for choosing FELIX Tec 4.

This quick start guide contains the following information for you to familiarize yourself with your 3D printer, to use it to

its best advantages and to benet fully from all the functions and the technical developments it incorporates.

It is well worth taking a few minutes to read this guide to familiarize yourself with the information and guidelines it

contains about the machine and its functions.

More manuals and tutorials can be found on www.felixprinters.com/support

Page 3

Chapter 1 – Unboxing

1.1 What’s in the Box?

1.2 Unboxing

1.3 Installing the Handle

1.4 Installing Accesoires and Cables

Chapter 2 – Prepare

2.1 Level Build Platform

2.2 Calibrate Z-Probe

2.3 Change lament

Chapter 3 – Print

3.1 Ensure a Succesfull Print

3.2 Printing via SD Card

3.3 Remove a 3D Printed Object

3.4 Remove Support Material

INTRODUCTION & CONTENT

Chapter 4 – Software and maintenance

4.1 Print your own 3D Models

4.2 Calibrate XY Offset

4.3 Calibrate Z Offset

Require additional support?

Have a look at www.felixprinters.com/support

or at our user forum.

FELIXprinters Quick Start Guide for the FELIX Tec 4

Page 4

FELIX Tec 4

System Specications

• Printer dimensions (L, W, H) 410 x 450 x 520 mm

• Weight 9 kg

• Power requirements: 220 V

Capabilities

• Build volume Single mode (L, W, H) 205 x 255 x 225 mm

• Build volume Dual mode (L, W, H) 205 x 240 x 225 mm

• Layer height range 0.05 - 0.25 mm

• Bed temperature: max. 90 °C

Extruders

• Diameter nozzle: 0.35 mm (optional 0.5mm)

• Max temperature: 275 °C

Website

www.FELIXprinters.com

Print materials

• Open source 1.75 mm filaments

• Tolerance: ± 0.15 mm

• PLA, PVA, ABS-X, PETG, PolyFlex, Wood, Glass

Connectivity

• Stand-alone micro-SD card printing

• USB cable connection

• Optional WiFi - The Element by Printr (external)

Software

• Optimized for Simplify3D and Repetier-Host

Contact

[email protected]

Zeemanlaan 15, 3401 MV IJsselstein, The Netherlands

Specs

FELIXprinters Quick Start Guide for the FELIX Tec 4

The Basics

Nozzles / Extruders

Flexible BuildPlate

Build Platform

Power Switch

Power Connection

USB Computer Cable

SD Card Slot

Filament tubes

Filament guide

Thumb screws

Filament

Filament spool holder

Display unit

Page 5FELIXprinters Quick Start Guide for the FELIX Tec 4

FELIXprinters Quick Start Guide for the FELIX Tec 4

1.1 What’s in the Box?

*We recommend to use the following tools: Spray Container with Alcohol, Paper Cloth, Scissors and Long Nose Pliers

1 x Allen Key

2 x Spool Holder

1 x Filament Guide

1 x USB-SD Adapter

1 x Handle Cover

1 x USB Cable

1 x Power Cable

1 x Handle

1 x Tweezers

1 x Micro SD Card

2 x Filament Tubes

Chapter 1: Unboxing

Page 6FELIXprinters Quick Start Guide for the FELIX Tec 4

Recommended

tools:

2 x T-nut M8N

2 x M8x16 Screw

Calibration

Card

E1 x Calibration Card

1 x Flexible BuildPlateN

FELIXprinters Quick Start Guide for the FELIX Tec 4

1.2 Unboxing

Chapter 1: Unboxing

Page 7Page 7FELIXprinters Quick Start Guide for the FELIX Tec 4

Open the box, remove the bumper and take out the

miscellaneous parts from the bumper.

Carefully remove the FELIX Tec 4 from the box.

FELIXprinters Quick Start Guide for the FELIX Tec 4

Page 8

Chapter 1: Unboxing

Remove the foam protection from the printer frame. Remove the ve red protective cable ties using cutting

pliers or a scissor.

4 5

123

FELIXprinters Quick Start Guide for the FELIX Tec 4

1.3 Installing the Handle

Page 9

Chapter 1: Unboxing

1. Put the T-nut upright into the T-slot of the prole.

2. Twist the T-nut 90 degrees in place.

3. Repeat this for both T-nuts.

1. Fix the handle against the vertical prole with the

two hexagon screws. Use a hex key size 5.

2. Press the handle cover on the handle

FELIXprinters Quick Start Guide for the FELIX Tec 4

1.4 Installing Accesoires and Cables

Chapter 1: Unboxing

Page 10

≈ 12 cm

≈ 20 cm

1. Place the rear of the Flexible BuildPlate on the edge.

2. Lower the front of the Flexible BuildPlate and make

sure all edges are inside the build platform.

Install the lament guide and spool holder(s) by placing

one edge in the T-slot and twisting it in place.

Otros manuales para Tec 4

Tabla de contenidos

Otros manuales de Impresora 3D de FELIXprinters

FELIXprinters

FELIXprinters Pro Series Guía de instalación y uso

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters FELIX Pro 2 Manual de usuario

FELIXprinters

FELIXprinters FELIX Tec 4.1 Manual de usuario

FELIXprinters

FELIXprinters FELIX One Manual de usuario

FELIXprinters

FELIXprinters Felix Pro 1 Manual de usuario

FELIXprinters

FELIXprinters 3 Series Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters Felix Pro 1 Manual de usuario

FELIXprinters

FELIXprinters Pro 2 Touch Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro L Manual de usuario

FELIXprinters

FELIXprinters Felix 2.0 Manual de usuario

FELIXprinters

FELIXprinters Pro Series Guía de instalación y uso

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters FELIX Pro 3 Touch Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de funcionamiento

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro Series Guía de instalación y uso

FELIXprinters

FELIXprinters Tec 4 Manual de usuario

FELIXprinters

FELIXprinters FELIX Pro 2 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario